Hot-rolled stainless steel plates - Tolerances on dimensions and shape (ISO 18286:2008)

ISO 18286:2008 specifies requirements for tolerances for hot-rolled stainless steel plates (quarto plates) made on a reversing mill with the following characteristics: nominal thickness, t, from 4 mm to 250 mm; and nominal width, w, equal to or greater than 600 mm.
Tolerances for plate of width w less than 600 mm cut or slit from wider plate should be agreed upon between manufacturer and purchaser at the time of enquiry and order.
ISO 18286:2008 is not applicable to round plates, custom-made plates, checker plate or bulb plate for flooring or wide flats, nor to continuous-process plates (plate made with coiling).

Warmgewalztes Blech aus nichtrostendem Stahl - Grenzabmaße und Formtoleranzen (ISO 18286:2008)

Diese Internationale Norm legt die Grenzabmaße und Formtoleranzen fest für warmgewalztes Blech aus nichtrostendem Stahl (Quartoblech) hergestellt durch Walzen auf einer Umkehrstraße, in:
a)   Nenndicken, 4 mm b)   Nennbreiten, w >or= 600 mm.
Die Grenzabmaße für Blech in Nennbreiten w < 600 mm nach Ablängen oder Längsteilen eines breiteren Bandes müssen zwischen Hersteller und Besteller vereinbart werden.
Diese Internationale Norm gilt nicht für Ronden, Skizzenbleche, Bleche mit eingewalzten Mustern, Breitflachstahl und ebenso nicht für kontinuierlich gewalztes Blech. Für diese Produkte gilt ISO 9444.

Tôles en acier inoxydable laminées à chaud - Tolérances sur les dimensions et la forme (ISO 18286:2008)

L'ISO 18286:2008 spécifie les exigences relatives aux tolérances pour les tôles en acier inoxydable laminées à chaud (tôles quarto) produites sur un laminoir réversible ayant les caractéristiques suivantes: épaisseur nominale, t, de 4 mm à 250 mm; largeur nominale, w, supérieure ou égale à 600 mm.
Il convient que les tolérances pour les tôles de largeur w inférieure à 600 mm, découpées ou refendues à partir de tôles plus larges, fassent l'objet d'un accord entre le producteur et l'acheteur lors de l'appel d'offres et de la commande.
L'ISO 18286:2008 n'est pas applicable aux tôles circulaires, tôles sur mesure, tôles gaufrées ou tôles à boudin pour sols, ou aux larges plats, ni aux tôles produites en continu (tôles en bobine).

Kontinuirno vroče valjane nerjavne pločevine - Mejni odstopki mer in tolerance oblik (ISO 18286:2008)

Ta mednarodni standard določa zahteve za mejne odstopke za nepretrgano vroče valjane nerjavne pločevine (kvadratne plošče), izdelane na reverzivnem valjalnem stroju, z naslednjimi značilnostmi:
a) 4 mm < nazivna debelina, d < 250 mm;
b) nazivna širina, š < 600 mm.
O mejnih odstopkih za izdelke s širino < 600 mm, ki se odrežejo ali odtrgajo s pločevine, se morata dogovoriti proizvajalec in kupec med poizvedbo in naročilom.
Ta mednarodni standard ne vključuje okroglih plošč, po meri narejenih plošč, plošč z vzorci ali izboklinami za talne obloge in široke ploskve. Ne vključuje plošč s stalnim procesom (plošč, narejenih z navitjem), ker mejne odstopke za te plošče opredeljuje drug mednarodni standard (glej ISO 9444).

General Information

Status
Published
Publication Date
01-Jun-2010
Withdrawal Date
30-Dec-2010
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
02-Jun-2010
Due Date
09-Aug-2011
Completion Date
02-Jun-2010

Buy Standard

Standard
EN ISO 18286:2011
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalztes Blech aus nichtrostendem Stahl - Grenzabmaße und Formtoleranzen (ISO 18286:2008)Tôles en acier inoxydable laminées à chaud - Tolérances sur les dimensions et la forme (ISO 18286:2008)Hot-rolled stainless steel plates - Tolerances on dimensions and shape (ISO 18286:2008)77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN ISO 18286:2010SIST EN ISO 18286:2011en01-september-2011SIST EN ISO 18286:2011SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 18286
June 2010 ICS 77.140.50 English Version
Hot-rolled stainless steel plates -Tolerances on dimensions and shape (ISO 18286:2008)
Tôles en acier inoxydable laminées à chaud - Tolérances sur les dimensions et la forme (ISO 18286:2008)
Warmgewalztes Blech aus nichtrostendem Stahl - Grenzabmaße und Formtoleranzen (ISO 18286:2008) This European Standard was approved by CEN on 20 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 18286:2010: ESIST EN ISO 18286:2011

Reference numberISO 18286:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO18286Second edition2008-12-15Hot-rolled stainless steel plates — Tolerances on dimensions and shape Tôles en acier inoxydable laminées à chaud — Tolérances sur les dimensions et la forme
ISO 18286:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
ISO 18286:2008(E) © ISO 2008 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Information to be supplied by the purchaser.1 3.1 General.1 3.2 Purchase order options.2 4 Designation.2 5 Form of supply.2 6 Tolerances on dimensions.3 6.1 Thickness.3 6.2 Width and length.3 7 Tolerances on shape.5 7.1 Edge camber and out-of-squareness.5 7.2 Flatness.5 8 Excess mass.6 9 Measurements.6 9.1 General.6 9.2 Thickness.6 9.3 Width.6 9.4 Length.6 9.5 Edge camber.7 9.6 Out-of-squareness.7 9.7 Flatness.7 10 Purchase order options.7 Bibliography.8
ISO 18286:2008(E) iv © ISO 2008 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 18286 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 4, Heat treatable and alloy steels. This second edition cancels and replaces the first edition (ISO 18286:2004), of which it constitutes a minor revision.
INTERNATIONAL STANDARD ISO 18286:2008(E) © ISO 2008 – All rights reserved 1Hot-rolled stainless steel plates — Tolerances on dimensions and shape 1 Scope This International Standard specifies requirements for tolerances for hot-rolled stainless steel plates (quarto plates) made on a reversing mill with the following characteristics: a) nominal thickness, t, such that 4 mm u t u 250 mm; b) nominal width, w, such that w W 600 mm. Tolerances for plate of width w < 600 mm cut or slit from wider plate should be agreed upon between manufacturer and purchaser at the time of enquiry and order. This International Standard is not applicable to round plates, custom-made plates, checker plate or bulb plate for flooring or wide flats, nor to continuous-process plates (plate made with coiling). This International Standard does not include round plates, custom-made plates, checker plate or bulb plate for flooring or wide flats. It does not include continuous process plates (plate made with coiling) because tolerances for these plates are defined in another International Standard (see ISO 9444). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TS 15510:2003, Stainless steels — Chemical composition ISO 16143-1:2004, Stainless steels for general purposes — Part 1: Flat products 3 Information to be supplied by the purchaser 3.1 General The following information shall be supplied by the purchaser at the time of enquiry and order: a) description of the product (plate); b) reference to this International Standard, ISO 18286; c) nominal thickness, in millimetres; d) nominal width, in millimetres; e) the letters NK, if plate with mill edges is required [see 6.2.2 and Clause 10 a)]; SIST EN ISO 18286:2011

ISO 18286:2008(E) 2 © ISO 2008 – All rights reserved f) nominal length, in millimetres; g) width and length tolerances, Class A (in accordance with Tables 2 and 3), Class B (in accordance with Table 4) or Class C (in accordance with Table 5), see 6.2; h) flatness tolerance class, Class N (in accordance with Table 6) or Class S (in accordance with Table 7), see 7.2.1; i) requirements concerning limits for excess mass (see Clause 8). 3.2 Purchase order options A number of options are listed in Clause 10. In the absence of any specification of these options by the purchaser at the time of enquiry and purchase order, the manufacturer is permitted to deliver in accordance with the basic requirements of this specification (see 5.2). 4 Designation The designation of products in accordance with 3.1 shall also include the exact designation of the ordered steel grade, in accordance with the following examples: a) plate in accordance with this International Standard with nominal thickness of 20 mm, nominal width 2 000 mm, with trimmed edges, nominal length 4 500 mm, with width and length tolerances Class B (in accordance with Table 4), with special flatness tolerances in accordance with Table 7 (Class S), grade X2CrNi18-9 as specified in ISO 16143-1:2004 plate ISO 18286 – 20 × 2000 × 4500 B S, steel ISO 16143-1 – X2CrNi18-9 b) plate in accordance with this International Standard with nominal thickness of 4,5 mm, nominal width 1 500 mm, with mill edge (NK), with width tolerance 1000+mm, nominal length 2 800 mm and length tolerance class A (in accordance with Table 3), with normal flatness tolerances in accordance with Table 6 (Class N), grade X2CrNiMo17-12
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.