iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14802:2005

(Main)

Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading

Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading

This European Standard specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It does not include requirements for testing the cover and frame. These requirements are specified in EN 124 or other standards depending on the material.
NOTE   Upper assembly components would normally include riser shafts, tapers, reducing slabs and telescopic joints.

Kunststoff-Rohrleitungssysteme - Kontrollschächte (Inspektionsöffnungen) und Einsteigschächte aus Thermoplasten - Bestimmung der Widerstandsfähigkeit gegen Belastungen der Oberfläche und Verkehrslasten

Diese Europäische Norm legt ein Verfahren zur Prüfung des Verhaltens der oberen Baugruppen von
Kontrollschächten und Bauteilen für Einsteigschächte unter Belastungen an der Oberfläche und Verkehrs-lasten
fest.
Sie beinhaltet keine Anforderungen an Prüfverfahren für die Abdeckung und den Rahmen. Diese
Anforderungen sind in EN 124 oder in anderen Normen, abhängig vom Werkstoff, festgelegt.
ANMERKUNG 1 Obere Baugruppen beinhalten üblicherweise Schachtrohre, Übergangsstücke, Reduzier-Platten sowie
Teleskop-Verbindungen.
ANMERKUNG 2 Dieses Prüfverfahren ist dafür vorgesehen, prEN 13598-2 und prEN 15229 (siehe Literaturhinweise) zu
unterstützen.

Systèmes de canalisations en plastique - Eléments de rehausse en thermoplastiques pour boîtes d'inspection et de branchement ou regards - Détermination de la résistance aux charges de remblai et de circulation

La présente Norme européenne spécifie une méthode permettant de tester la résistance aux charges de
remblai et de circulation de l’assemblage supérieur des boîtes d’inspection et de branchement et des
composants de regards.
Elle ne couvre pas les exigences d’essai relatives au tampon et au cadre. Celles-ci sont spécifiées dans
l’EN 124 ou dans d’autres normes selon le type de matériau.
NOTE 1 Les composants de l’assemblage supérieur comprennent habituellement les éléments de rehausse, les
parties coniques, les dalles réductrices et les raccordements ajustables.
NOTE 2 La présente méthode d’essai est destinée à supporter les prEN 13598-2 et prEN 15229 (voir en bibliographie).

Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading

General Information

Status
Withdrawn
Publication Date
06-Dec-2005
Withdrawal Date
10-Jan-2023
ICS
93.025 - External water conveyance systems
93.030 - External sewage systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 20 - Thermoplastics ancillaries for soil and waste discharge and gravity buried drainage and sewerage systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
11-Jan-2023
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/118 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on waste water engineering products
Ref Project
SIST EN 14802:2006 - Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading

Relations

Replaced By
EN ISO 13266:2023 - Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
Effective Date
16-Jan-2023

Buy Standard

EN 14802:2006EN 14802:2006
PreviousNext
Standard
EN 14802:2006
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14802:2006
01-april-2006
Plastics piping systems - Thermoplastics shafts or risers for inspection chambers
and manholes - Determination of resistance against surface and traffic loading
Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and
manholes - Determination of resistance against surface and traffic loading
Kunststoff-Rohrleitungssysteme - Kontrollschächte (Inspektionsöffnungen) und
Einsteigschächte aus Thermoplasten - Bestimmung der Widerstandsfähigkeit gegen
Belastungen der Oberfläche und Verkehrslasten
Systemes de canalisations en plastique - Eléments de rehausse en thermoplastiques
pour boîtes d'inspection et de branchement ou regards - Détermination de la résistance
aux charges de remblai et de circulation
Ta slovenski standard je istoveten z: EN 14802:2005
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.025 Zunanji sistemi za prevajanje External water conveyance
vode systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 14802:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14802:2006

---------------------- Page: 2 ----------------------

SIST EN 14802:2006
EUROPEAN STANDARD
EN 14802
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 93.025; 93.030

English Version
Plastics piping systems - Thermoplastics shafts or risers for
inspection chambers and manholes - Determination of
resistance against surface and traffic loading
Systèmes de canalisations en plastique - Eléments de Kunststoff-Rohrleitungssysteme - Kontrollschächte
rehausse en thermoplastiques pour boîtes d'inspection et (Inspektionsöffnungen) und Einsteigschächte aus
de branchement ou regards - Détermination de la Thermoplasten - Bestimmung der Widerstandsfähigkeit
résistance aux charges de remblai et de circulation gegen Belastungen der Oberfläche und Verkehrslasten
This European Standard was approved by CEN on 4 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14802:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14802:2006
EN 14802:2005 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references.4
3 Terms and definitions .4
4 Principle.5
5 Apparatus .5
6 Number of test pieces.7
7 Conditioning and test temperatures.7
8 Procedure .7
9 Test parameters .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 1452-1:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General (ISO 1452-1:2009)
SIST EN ISO 1452-1:2010

ISO 1452-1:2009 specifies the general aspects of unplasticized poly(vinyl chloride) (PVC‑U) solid-wall piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure.
In conjunction with ISO 1452-2, ISO 1452-3, ISO 1452-4 and ISO 1452-5, it is applicable to PVC‑U pipes, fittings, valves and ancillary equipment, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-2:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes (ISO 1452-2:2009)
SIST EN ISO 1452-2:2010

ISO 1452-2:2009 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC‑U pipes without a socket and pipes with a socket (integral or not), intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to pipes for the conveyance of water and waste water up to and including 45 °C and to a range of pipe sizes and pressure classes. It gives requirements concerning colours.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-1:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General (ISO 1452-1:2009)
SIST EN ISO 1452-1:2010

ISO 1452-1:2009 specifies the general aspects of unplasticized poly(vinyl chloride) (PVC‑U) solid-wall piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure.
In conjunction with ISO 1452-2, ISO 1452-3, ISO 1452-4 and ISO 1452-5, it is applicable to PVC‑U pipes, fittings, valves and ancillary equipment, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-2:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes (ISO 1452-2:2009)
SIST EN ISO 1452-2:2010

ISO 1452-2:2009 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC‑U pipes without a socket and pipes with a socket (integral or not), intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to pipes for the conveyance of water and waste water up to and including 45 °C and to a range of pipe sizes and pressure classes. It gives requirements concerning colours.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14801:2006(Main)
Conditions for pressure classification of products for water and wastewater pipelines
SIST EN 14801:2006

This document applies to components (pipes, joints, fittings, ferrules and valves), which have pressure related classification in European Standards covering products which are intended to be used for buried water supply and waste water pressure pipelines outside buildings. It specifies combinations of loading conditions and installation conditions to be used in the design method by reference to the relevant product standard for the determination of the allowable pressures (PFA, PMA and PEA) as defined in EN 805.
This document does not apply as an installation guide.
NOTE 1   This document does not give the full range of installation and loading parameters for all components and does not specify calculation and/or test methods for determination of the allowable pressures.
NOTE 2   This document does not relieve designers of their obligation under EN 805:2000, 8.4; e.g. to consider all conditions not addressed in clause 5 (e. g. seismic loads).
NOTE 3   This document does not deal with marking of components.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 683-2:2024(Main)
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
kSIST FprEN 683-2:2024

This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy finstock.
The chemical composition limits of these materials are specified in EN 573 3, unless otherwise agreed between supplier and purchaser.
The designations of wrought aluminium and wrought aluminium alloys and the temper designations used in this document are specified in EN 573 3, and the temper designations are defined in EN 515.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day