CEN ISO/TS 12781-1:2007
(Main)Geometrical product specifications (GPS) - Flatness - Part 1: Vocabulary and parameters of flatness (ISO/TS 12781-1:2003)
Geometrical product specifications (GPS) - Flatness - Part 1: Vocabulary and parameters of flatness (ISO/TS 12781-1:2003)
ISO/TS 12781-1:2003 defines the terms and concepts related to flatness of individual complete integral features only.
Geometrische Produktspezifikation (GPS) - Ebenheit - Teil 1: Begriffe und Kenngrößen der Ebenheit (ISO/TS 12781-1:2003)
Dieser Teil von ISO/TS 12781 definiert Begriffe und Kenngrößen bezüglich der Ebenheit von vollständigen Geometrieelementen.
Spécification géométrique des produits (GPS) - Planéité - Partie 1: Vocabulaire et paramètres de planéité (ISO/TS 12781-1:2003)
L'ISO/TS 12781-1:2003 définit les termes et concepts liés uniquement à la planéité des éléments intégraux complets individuels.
Specifikacija geometrijskih veličin izdelka - Ravnost - 1. del: Slovar in parametri ravnosti (ISO/TS 12781-1:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 12781-1:2008
01-april-2008
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND5DYQRVWGHO 6ORYDULQSDUDPHWUL
UDYQRVWL ,6276
Geometrical product specifications (GPS) - Flatness - Part 1: Vocabulary and parameters
of flatness (ISO/TS 12781-1:2003)
Geometrische Produktspezifikation (GPS) - Ebenheit - Teil 1: Begriffe und Kenngrößen
der Ebenheit (ISO/TS 12781-1:2003)
Spécification géométrique des produits (GPS) - Planéité - Partie 1: Vocabulaire et
parametres de planéité (ISO/TS 12781-1:2003)
Ta slovenski standard je istoveten z: CEN ISO/TS 12781-1:2007
ICS:
01.040.17
17.040.01
SIST-TS CEN ISO/TS 12781-1:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
TECHNICAL SPECIFICATION
CEN ISO/TS 12781-1
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
December 2007
ICS 01.040.17; 17.040.01
English Version
Geometrical product specifications (GPS) - Flatness - Part 1:
Vocabulary and parameters of flatness (ISO/TS 12781-1:2003)
Spécification géométrique des produits (GPS) - Planéité - Geometrische Produktspezifikation (GPS) - Ebenheit - Teil
Partie 1: Vocabulaire et paramètres de planéité (ISO/TS 1: Begriffe und Kenngrößen der Ebenheit (ISO/TS 12781-
12781-1:2003) 1:2003)
This Technical Specification (CEN/TS) was approved by CEN on 8 October 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 12781-1:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
CEN ISO/TS 12781-1:2007 (E)
Contents Page
Foreword.3
2
---------------------- Page: 3 ----------------------
CEN ISO/TS 12781-1:2007 (E)
Foreword
The text of ISO/TS 12781-1:2003 has been prepared by Technical Committee ISO/TC 213 “Dimensional and
geometrical product specifications and verification” of the International Organization for Standardization (ISO)
and has been taken over as CEN ISO/TS 12781-1:2007 by Technical Committee CEN/TC 290 “Dimensional
and geometrical product specification and verification” the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO/TS 12781-1:2003 has been approved by CEN as a CEN ISO/TS 12781-1:2007 without any
modification.
3
---------------------- Page: 4 ----------------------
TECHNICAL ISO/TS
SPECIFICATION 12781-1
First edition
2003-12-01
Geometrical Product Specifications
(GPS) — Flatness —
Part 1:
Vocabulary and parameters of flatness
Spécification géométrique des produits (GPS) — Planéité —
Partie 1: Vocabulaire et paramètres de planéité
Reference number
ISO/TS 12781-1:2003(E)
©
ISO 2003
---------------------- Page: 5 ----------------------
ISO/TS 12781-1:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unle
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.