iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 603-2:1996

(Main)

Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties

Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties

This Part of EN 603 specifies the mechanical properties of wrought forging stock in aluminium and aluminium alloys for general engineering applications.  The chemical composition and temper designations for these alloys are specified in EN 573-3 and EN 515 respectively.

Aluminium und Aluminiumlegierungen - Stranggepreßtes oder gewalztes Schmiedevormaterial - Teil 2: Mechanische Eigenschaften

Dieser Teil von EN 603 legt die mechanischen Eigenschaften von stranggepreßtem und gewalzten Schmiedevormaterial aus Aluminium und Aluminiumlegierungen fest, das für allgemeine Anwendungen eingesetzt wird. Die chemische Zusammensetzung dieser Werkstoffe ist in EN 573-3 und die Bezeichnungen der Werkstoffzustände sind in EN 515 angegeben.

Aluminium et alliages d'aluminium - Produits corroyés destinés à la forge - Partie 2: Caractéristiques mécaniques

La présente partie de l'EN 603 spécifie les caractéristiques mécaniques des produits corroyés en aluminium et alliages d'aluminium destinés à la forge pour applications mécaniques générales. La composition chimique et la désignation des états métallurgiques de ces alliages sont respectivement spécifiées dans les normes européennes EN 573-3 et EN 515.

Aluminij in aluminijeve zlitine - Gneteni surovci za kovanje - 2. del: Mehanske lastnosti

General Information

Status
Withdrawn
Publication Date
17-Sep-1996
Withdrawal Date
17-Sep-2024
ICS
77.150.10 - Aluminium products
Technical Committee
CEN/TC 132 - Aluminium and aluminium alloys
Drafting Committee
CEN/TC 132/WG 3 - Forgings and wrought and cast forging stock
Current Stage
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 603-2:1998 - Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties

Relations

Replaced By
EN 603-2:2024 - Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties
Effective Date
07-Jun-2023

Buy Standard

EN 603-2:1998EN 603-2:1998
PreviousNext
Standard
EN 603-2:1998
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminij in aluminijeve zlitine - Gneteni surovci za kovanje - 2. del: Mehanske lastnostiAluminium und Aluminiumlegierungen - Stranggepreßtes oder gewalztes Schmiedevormaterial - Teil 2: Mechanische EigenschaftenAluminium et alliages d'aluminium - Produits corroyés destinés a la forge - Partie 2: Caractéristiques mécaniquesAluminium and alumini
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 603-2:2024(Main)
Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties
SIST EN 603-2:2024

This document, part of EN 603 series of standards, specifies the mechanical properties of wrought forging stock in aluminium and aluminium alloys for general engineering applications.
The chemical composition and temper designations for these alloys are specified in EN 573 3 and EN 515 respectively.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1396:2023(Main)
Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications
SIST EN 1396:2023

This document specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm.
It is applicable to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process both with liquid as well as with powder paints, either in the final width or slit afterwards, and to sheet obtained from such strip.
It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are dealt with in separate EN 541.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12020-2:2022(Main)
Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 2: Tolerances on dimensions and form
SIST EN 12020-2:2023

This document specifies tolerances on dimensions and form of extruded precision profiles in alloys EN AW-6060 and EN AW-6063, manufactured with and without a thermal barrier (see Figures 1 and 2). It applies to extruded products supplied without further surface treatment. Precision profiles covered in this document are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
- they are designed with mostly uniform wall-thicknesses;
- they are mainly used for mechanical engineering, architectural and automotive (except crash-elements) applications;
- their maximum weight per metre is 10 kg/m;
- their maximum wall thickness ratio (tmax/tmin) is 3,5.
In the case of profiles which, due to the complexity of their design, are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached.
NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by this document although the actual thermal barrier material itself is not (see EN 14024).

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12392:2016+A1:2022(Main + Amendment)
Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
SIST EN 12392:2016+A1:2022

This European Standard specifies the material requirements and testing procedures applicable to wrought and cast aluminium and aluminium alloys intended for use in the production of pressure equipment.
This European Standard covers:
-   the products forms, grades and tempers of wrought and cast aluminium and aluminium alloys which may be used for such applications together with data for wrought and cast alloys over their permissible working temperature ranges;
-   the permissible alloys/ tempers covered by this are those given in Table A.1 and in B.1 for wrought alloys and in Table A.2 and in B.2 for castings;
-   the technical conditions for inspection and delivery, mechanical property limits and tolerances on form and dimensions by reference to the appropriate European standards for the relevant wrought and cast aluminium and aluminium alloys, and
-   additional requirements which are specific to pressure equipment applications.
It applies to hot-rolled plate, cold-rolled sheet/ strip/ circles, extruded or extruded and cold drawn rod/bar, tube, extruded open / hollow profiles, forgings and castings, by this standard are those given in Table A.1 for wrought alloys and in Table A.2 for castings.
It is the sole objective of this standard to cover materials only for pressure purposes and it excludes any elements of fabrication or fabrication methods for pressure equipment; such information can be found in the relevant standards listed in the "Bibliography" section.

  • Standard
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 941:2022(Main)
Aluminium and aluminium alloys - Circle and circle stock for the production of general applications - Specifications
SIST EN 941:2022

This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications.
It applies to:
—   circles made out of hot or cold rolled circles stock by:
•   blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;
•   sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
—   hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3 500 mm.
It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 851:2022(Main)
Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
SIST EN 851:2022

This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This document is applicable to:
—   circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm;
NOTE   Circles with a diameter up to 1 000 mm can be produced by blanking.
—   hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.
This document is not applicable to slugs for impact extrusions which are dealt with in other European Standards.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12020-1:2022(Main)
Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery
SIST EN 12020-1:2022

This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment.
Precision profiles for which this document is applicable are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
—   they are designed with mostly uniform wall-thicknesses;
—   they are mainly used for mechanical engineering, architectural and automotive (except crash-elements) applications;
—   the maximum weight by meter is 10 kg/m;
—   the max. wall-thickness proportion (tmax/tmin) of 3,5.
In the case of profiles, which, due to the complexity of their design are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached.
NOTE   The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020-2 although the actual thermal barrier material itself is not (see EN 14024).

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 603-3:2021(Main)
Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form
SIST EN 603-3:2021

This document specifies the tolerances on dimensions and form of wrought aluminium and aluminium alloy forging stock.
It applies to extruded and rolled products.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1706:2020+A1:2021(Main + Amendment)
Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
SIST EN 1706:2020+A1:2021

This document specifies the chemical composition limits for aluminium casting alloys and mechanical properties of separately cast test pieces for these alloys.
Annex C is included as a guide to the selection of alloys for a specific use or process.
This document is intended to be used in conjunction with EN 576, EN 1559-1, EN 1559-4, EN 1676 and EN ISO 8062-3.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1676:2020(Main)
Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications
SIST EN 1676:2020

This document defines the requirements for grades of alloyed aluminium ingots intended for remelting.
It specifies the classifications and designations applicable to these grades, the conditions in which they are produced, their properties and the marks by which they are identified.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day