FprEN 54-5 rev

Fire detection and fire alarm systems - Part 5: Heat detectors - Point detectors

This European Standard specifies the requirements, test methods and performance criteria for point heat detectors for use in fire detection and fie alarm systems for buildings (see EN 54-1: 1996).
For other types of heat detector, or for detectors intended for use in other environments, this standard should only be used for guidance.  Heat detectors with special characteristics and developed for specific risks are not covered by this standard.

Brandmeldeanlagen - Teil 5: Wärmemelder - Punktförmige Melder

Diese Europäische Norm legt Anforderungen, Prüfverfahren und Leistungsmerkmale für punktförmige Wärmemelder fest, die in Brandmeldeanlagen für Gebäude eingesetzt werden (siehe EN 54-1:1996).
Für andere Typen von Wärmemeldern, oder für Wärmemelder, die für die Anwendung unter anderen Umgebungsbedingungen vorgesehen sind, sollte die vorliegende Norm nur als Leitfaden angewendet werden. Wärmemelder mit speziellen Merkmalen, die für besondere Risiken entwickelt wurden, sind nicht Gegenstand dieser Norm.

Systèmes de détection et d'alarme incendie - Partie 5: Détecteurs de chaleur - Détecteurs ponctuels

La présente Norme européenne spécifie les exigences, les méthodes d'essai et les critères de performance des détecteurs ponctuels de chaleur utilisés dans les systèmes de détection et d'alarme incendie installés dans les bâtiments (voir EN 54-1:1996).
Pour d'autres types de détecteurs de chaleur ou pour ceux fonctionnant dans des environnements différents, il convient d'utiliser cette norme comme un guide. Les détecteurs de chaleur possédant des caractéristiques particulières, conçus pour des risques spéciaux, ne sont pas couverts par la présente norme.

Sistemi za odkrivanje in javljanje požara ter alarmiranje - 5. del: Toplotni javljalniki - Točkovni javljalniki

General Information

• Status: Not Published
• Publication Date: 24-Mar-2013
• ICS: 13.220.20 - Fire protection
• Technical Committee: CEN/TC 72 - Fire detection and fire alarm systems
• Drafting Committee: CEN/TC 72/WG 5 - Point heat and smoke detectors and short-circuit isolators
• Current Stage: 4598 - Decision to abandon - Finalization for Vote
• Start Date: 22-May-2013
• Completion Date: 22-May-2013
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/109 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on fire alarm/detection, fixed firefighting, fire and smoke control and explosion suppression products
• Ref Project: oSIST prEN 54-5:2011 - Fire detection and fire alarm systems - Part 5: Heat detectors - Point detectors

Relations

• Revises: EN 54-5:2000 - Fire detection and fire alarm systems - Part 5: Heat detectors - Point detectors
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2011
6LVWHPL]DRGNULYDQMHLQMDYOMDQMHSRåDUDWHUDODUPLUDQMHGHO7RSORWQLMDYOMDOQLNL
7RþNRYQLMDYOMDOQLNL
Fire detection and fire alarm systems - Part 5: Heat detectors - Point detectors
Brandmeldeanlagen - Teil 5: Wärmemelder - Punktförmige Melder
Systèmes de détection et d'alarme incendie - Partie 5: Détecteurs de chaleur -
Détecteurs ponctuels
Ta slovenski standard je istoveten z: prEN 54-5 rev
ICS:
13.220.20 3RåDUQD]DãþLWD Fire protection
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
DRAFT
prEN 54-5 rev
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 13.220.20 Will supersede EN 54-5:2000
English Version
Fire detection and fire alarm systems - Part 5: Heat detectors -
Point detectors
Systèmes de détection et d'alarme incendie - Partie 5: Brandmeldeanlagen - Teil 5: Wärmemelder - Punktförmige
Détecteurs de chaleur - Détecteurs ponctuels Melder
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 72.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 54-5 rev:2011: E
worldwide for CEN national Members.

prEN 54-5:2011 (E)
Contents Page
Foreword .5
1 Scope .7
2 Normative references .7
3 Terms and definitions .8
4 Requirements .9
4.1 General .9
4.1.1 Compliance .9
4.1.2 Classification .9
4.2 Operational reliability . 10
4.2.1 Position of heat sensitive elements . 10
4.2.2 Individual alarm indication . 10
4.2.3 Connection of ancillary devices . 10
4.2.4 Monitoring of detachable detectors . 10
4.2.5 Manufacturer's adjustments . 10
4.2.6 On-site adjustment of response behaviour . 10
4.2.7 Marking . 11
4.2.8 Data . 11
4.2.9 Additional requirements for software controlled detectors . 11
4.3 Nominal activation conditions/sensitivity . 13
4.3.1 Directional Dependence requirements . 13
4.3.2 Static response temperature . 13
4.3.3 Response times from typical application temperature . 13
4.3.4 Response times from 25 °C . 13
4.3.5 Response times from high ambient temperature (Dry heat operational) . 13
4.3.6 Reproducibility . 14
4.4 Response delay (response time): . 14
4.4.1 Additional tests for detectors with class suffixes . 14
4.5 Tolerance to supply voltage: . 14
4.5.1 Variation in supply parameters . 14
4.6 Durability of operational reliability, temperature resistance: . 14
4.6.1 Cold (operational) . 14
4.6.2 Dry heat (endurance) . 14
4.7 Durability of operational reliability, humidity resistance: . 14
4.7.1 Damp heat, cyclic (operational) . 14
4.7.2 Damp heat, steady state (endurance) . 15
4.8 Durability of operational reliability, corrosion resistance: . 15
4.8.1 Sulphur dioxide (SO ) corrosion (endurance) . 15
4.9 Durability of operational reliability, vibration resistance: . 15
4.9.1 Shock (operational) . 15
4.9.2 Impact (operational). 15
4.9.3 Vibration, sinusoidal, (operational). 15
4.9.4 Vibration, sinusoidal (endurance) . 15
4.10 Durability of operational reliability, electrical stability: . 15
4.10.1 Electromagnetic Compatibility (EMC), Immunity tests (operational) . 15
5 Tests . 15
5.1 General . 15
5.1.1 Atmospheric conditions for tests . 15
5.1.2 Operating conditions for tests . 16
5.1.3 Mounting arrangements . 16
prEN 54-5:2011 (E)
5.1.4 Tolerances . 16
5.1.5 Measurement of response time . 16
5.1.6 Provision for tests . 17
5.1.7 Test schedule . 17
5.2 Operational reliability . 20
5.2.1 Position of heat sensitive elements . 20
5.2.2 Individual alarm indication . 20
5.2.3 Connection of ancillary devices . 20
5.2.4 Monitoring of detachable detectors . 20
5.2.5 Manufacturer's adjustments . 20
5.2.6 On-site adjustment of response behaviour . 20
5.2.7 Marking . 20
5.2.8 Data . 20
5.2.9 Additional requirements for software controlled detectors . 20
5.3 Nominal activation conditions/sensitivity . 21
5.3.1 Directional dependence . 21
5.3.2 Static response temperature . 21
5.3.3 Response times from typical application temperature . 22
5.3.4 Response times from 25 °C . 23
5.3.5 Response times from high ambient temperature (Dry heat operational) . 23
5.3.6 Reproducibility . 24
5.4 Response delay (response time): . 24
5.4.1 Additional tests for detectors with class suffixes . 24
5.5 Tolerance to supply voltage: . 26
5.5.1 Variation in supply parameters . 26
5.6 Durability of operational reliability, temperature resistance: . 27
5.6.1 Cold (operational) . 27
5.6.2 Dry heat (endurance) . 28
5.7 Durability of operational reliability, humidity resistance: . 29
5.7.1 Damp heat, cyclic (operational) . 29
5.7.2 Damp heat, steady state (endurance) .
...