Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012)

ISO 8503-2:2012 describes a visual and tactile method for assessing the grade of the profile which is produced by one of the abrasive blast-cleaning procedures described in ISO 8504‑2.
The method uses ISO surface profile comparators for assessing, on site, the roughness of surfaces before the application of paint or other protective treatments.
The method is applicable to steel surfaces which have been blast-cleaned by use of either shot abrasives or grit abrasives, but is only applicable to grades Sa 2½ and Sa 3 of ISO 8501‑1 where the entire surface under test shows an overall blast-cleaned appearance.
lt is applicable to surfaces which have been cleaned with either metallic or non-metallic abrasives.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Rauheitskenngrößen von gestrahlten Stahloberflächen - Teil 2: Verfahren zur Prüfung der Rauheit von gestrahltem Stahl - Vergleichsmusterverfahren (ISO 8503-2:2012)

Dieser Teil von ISO 8503 beschreibt ein Verfahren für den Sicht- und Tastvergleich zur Feststellung des Grades der Rauheit, die durch eines der in ISO 8504-2 beschriebenen Strahlverfahren entstanden ist.
Nach dem Verfahren werden ISO-Rauheitsvergleichsmuster benutzt, mit denen der Rauheitsgrad vor Ort geprüft werden kann, bevor Beschichtungsstoffe aufgebracht oder andere Schutzmaßnahmen durchgeführt werden.
ANMERKUNG   Wenn es zweckmäßig ist, dürfen die Vergleichsmuster auch zum Beurteilen der Rauheit anderer gestrahlter Oberflächen benutzt werden. Darüber hinaus dürfen sie auch bei solchen Oberflächen angewendet werden, die nicht beschichtet werden sollen.
Das Verfahren ist für Stahloberflächen anwendbar, die mit kantigen oder kugeligen Strahlmitteln gestrahlt worden sind. Es ist aber nur anwendbar für die Oberflächenvorbereitungsgrade Sa 2 1/2 und Sa 3 nach ISO 8501-1, wenn die gesamte Prüffläche gleichmäßig gestrahlt wurde.
Das Verfahren ist für Oberflächen anwendbar, die mit metallischen oder nichtmetallischen Strahlmitteln gestrahlt worden sind.

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Caractéristiques de rugosité des subjectiles d'acier décapés - Partie 2: Méthode de classification d'un profil de surface en acier décapée par projection d'abrasif - Utilisation des comparateurs viso-tactiles (ISO 8503-2:2012)

L'ISO 8503-2:2012 décrit une méthode visuelle et tactile destinée à évaluer le profil d'une surface préparée par l'une des méthodes par projection d'abrasif décrites dans l'ISO 8504-2.
La méthode prévoit l'utilisation de comparateurs viso-tactiles ISO pour évaluer, sur site, la rugosité des surfaces avant l'application de peintures ou d'autres traitements de protection.
La méthode est applicable aux subjectiles d'acier décapés par projection d'abrasifs ronds ou angulaires, mais elle ne s'applique qu'aux surfaces présentant un degré de préparation Sa 2½ et Sa 3 selon l'ISO 8501‑1, lorsque toute la surface soumise à essai présente un aspect uniforme après décapage.
Elle est applicable à des surfaces décapées avec des abrasifs métalliques ou non métalliques.

Priprava jeklenih podlag pred nanašanjem barvnih in sorodnih premazov - Površinske hrapave značilnosti peskanih jeklenih podlag - 2. del: Metoda za ocenjevanje stopnje hrapavosti površin, peskanih z abrazivom - Primerjalni postopek (ISO 8503-2:2012)

Ta del standarda ISO 8503 opisuje vidno in otipno metodo za oceno stopnje hrapavosti, ki se doseže s postopkom peskanja z abrazivom, opisanim v standardu ISO 8504-2. Metoda uporablja primerjalne standarde površinske hrapavosti ISO, s katerimi se na kraju samem oceni hrapavost površin pred nanašanjem barve ali drugih zaščitnih premazov. Metoda se uporablja za jeklene površine, ki so bile peskane z abrazivom v obliki sekancev ali kroglic, vendar se uporablja le za kategoriji Sa 2? in Sa 3 standarda ISO 8501-1, pri čemer je celotna preskušena površina videti peskana. Uporablja se za površine, ki so bile očiščene s kovinskimi ali nekovinskimi abrazivi.

General Information

Status
Published
Publication Date
14-Feb-2012
Withdrawal Date
30-Aug-2012
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
15-Feb-2012
Completion Date
15-Feb-2012

Relations

Buy Standard

Standard
EN ISO 8503-2:2012
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8503-2:2012
01-maj-2012
1DGRPHãþD
SIST EN ISO 8503-2:1997
3ULSUDYDMHNOHQLKSRGODJSUHGQDQDãDQMHPEDUYQLKLQVRURGQLKSUHPD]RY
3RYUãLQVNHKUDSDYH]QDþLOQRVWLSHVNDQLKMHNOHQLKSRGODJGHO0HWRGD]D
RFHQMHYDQMHVWRSQMHKUDSDYRVWLSRYUãLQSHVNDQLK]DEUD]LYRP3ULPHUMDOQL
SRVWRSHN ,62
Preparation of steel substrates before application of paints and related products -
Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for
the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure
(ISO 8503-2:2012)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Rauheitskenngrößen von gestrahlten Stahloberflächen - Teil 2: Verfahren zur Prüfung
der Rauheit von gestrahltem Stahl; Vergleichsmusterverfahren (ISO 8503-2:2012)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Caractéristiques de rugosité des subjectiles d'acier décapés - Partie 2:
Méthode pour caractériser un profil de surface en acier décapée par projection d'abrasif -
Utillisation d'échantillons de comparaison viso-tactile (ISO 8503-2:2012)
Ta slovenski standard je istoveten z: EN ISO 8503-2:2012
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
SIST EN ISO 8503-2:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8503-2:2012

---------------------- Page: 2 ----------------------

SIST EN ISO 8503-2:2012


EUROPEAN STANDARD
EN ISO 8503-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2012
ICS 25.220.10 Supersedes EN ISO 8503-2:1995
English Version
Preparation of steel substrates before application of paints and
related products - Surface roughness characteristics of blast-
cleaned steel substrates - Part 2: Method for the grading of
surface profile of abrasive blast-cleaned steel - Comparator
procedure (ISO 8503-2:2012)
Préparation des subjectiles d'acier avant application de
Vorbereitung von Stahloberflächen vor dem Auftragen von
peintures et de produits assimilés - Caractéristiques de Beschichtungsstoffen - Rauheitskenngrößen von
rugosité des subjectiles d'acier décapés - Partie 2: Méthode gestrahlten Stahloberflächen - Teil 2: Verfahren zur Prüfung
de classification d'un profil de surface en acier décapée par der Rauheit von gestrahltem Stahl;
projection d'abrasif - Utilisation des comparateurs viso- Vergleichsmusterverfahren (ISO 8503-2:2012)
tactiles (ISO 8503-2:2012)
This European Standard was approved by CEN on 14 February 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8503-2:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 8503-2:2012
EN ISO 8503-2:2012 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 8503-2:2012
EN ISO 8503-2:2012 (E)
Foreword
This document (EN ISO 8503-2:2012) has been prepared by Technical Committee ISO/TC 35 “Paints and
varnishes” in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at
the lat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.