EN ISO 11116-2:1999
(Main)Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11116-2:1999)
Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11116-2:1999)
This International Standard specifies types, dimensions and principles of use of gauges, to be used in conjunction with the taper thread specified in Part 1. Annex A provides examples of calculations for thread gauge dimensions on the large end diameter. Annex B draws attention to the limitations of the gauging system.
Ortsbewegliche Gasflaschen - Gasflaschen - 17E kegeliges Gewinde zum Anschluß von Ventilen an Gasflaschen - Teil 2: Prüflehren (ISO 11116-2:1999)
Dieser Teil von ISO 11116 legt Typen, Maße und Anwendungsgrundsätze von Lehren für kegelige Gewinde, die in Verbindung mit dem kegeligen Gewinde nach EN ISO 11116-1 angewendet werden, fest. Anhang A entha(lt Berechnungs- beispiele fu(r die Maße von Gewindelehren fu(r den großen Kegeldurchmesser. Anhang B informiert u(ber die Grenzen des in vorliegender Norm festgelegten Lehren-Systems.
Bouteilles à gaz - Filetage conique 17E pour le raccordement des robinets sur les bouteilles à gaz - Partie 2: Calibres de vérification (ISO 11116-2:1999)
La CEI 61300-3-49:2013 décrit la procédure nécessaire pour mesurer la force de rétention de la broche de guidage des connecteurs multifibres à férule rectangulaire, afin d'assurer que les broches restent en place durant l'accouplement et le désaccouplement.
Mots clé: force de rétention de la broche de guidage des connecteurs multifibres à férule rectangulaire
Plinske jeklenke - Konični navojni priključek 17E za ventile plinskih jeklenk - 2. del: Kalibri za kontrolo (ISO 11116-2:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11116-2:2000
01-januar-2000
3OLQVNHMHNOHQNH.RQLþQLQDYRMQLSULNOMXþHN(]DYHQWLOHSOLQVNLKMHNOHQNGHO
.DOLEUL]DNRQWUROR ,62
Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 2:
Inspection gauges (ISO 11116-2:1999)
Ortsbewegliche Gasflaschen - Gasflaschen - 17E kegeliges Gewinde zum Anschluß von
Ventilen an Gasflaschen - Teil 2: Prüflehren (ISO 11116-2:1999)
Bouteilles a gaz - Filetage conique 17E pour le raccordement des robinets sur les
bouteilles a gaz - Partie 2: Calibres de vérification (ISO 11116-2:1999)
Ta slovenski standard je istoveten z: EN ISO 11116-2:1999
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST EN ISO 11116-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11116-2:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 11116-2:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 11116-2:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 11116-2:2000
INTERNATIONAL ISO
STANDARD 11116-2
First edition
1999-04-01
Gas cylinders — 17E taper thread for
connection of valves to gas cylinders —
Part 2:
Inspection gauges
Bouteilles à gaz — Filetages coniques 17E pour le raccordement des
robinets sur les bouteilles à gaz —
Partie 2: Calibres de vérification
A
Reference number
ISO 11116-2:1999(E)
---------------------- Page: 5 ----------------------
SIST EN ISO 11116-2:2000
ISO 11116-2:1999(E)
Contents
Page
1 Scope .1
2 Terms and definitions .1
3 Requirements.1
3.1 Materials .1
3.2 Thread profile.2
3.3 Thread rotation.3
3.4 Taper .3
3.5 Thread profile.3
3.6 Pitch, P.3
4 Gauge dimensions.3
5 Inspection gauges .4
5.1 Cylinder neck thread .4
5.2 Valve stem thread .5
5.3 Check gauges.7
6 Use of inspection gauges .7
6.1 Plain gauges.7
6.2 Threaded gauges .7
6.3 Accept or reject criteria, using plug gauges.7
6.4 Accept or reject criteria, using ring gauges.7
7 Verification of inspection gauges .10
7.1 General.10
7.2 Plug gauges.10
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
---------------------- Page: 6 ----------------------
SIST EN ISO 11116-2:2000
©
ISO
ISO 11116-2:1999(E)
7.3 Ring gauges . 10
7.4 Use of check gauges. 10
8 Identification . 10
8.1 Inspection gauges . 10
8.2 Check gauges . 11
Annex A (informative) Examples of calculation for thread gauge dimensions on the large end diameter. 12
Annex B (informative) Limitations of gauging system. 13
iii
---------------------- Page: 7 ----------------------
SIST EN ISO 11116-2:2000
© ISO
ISO 11116-2:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 11116-2 was prepared by Technical Committee ISO/TC 58, Gas cylinders,
Subcommittee SC2, Cylinder fittings.
ISO 11116 consists of the following parts, under the general title Gas cylinders — 17E taper thread for connection
of valves to gas cylinders:
Part 1: Specification
Part 2: Inspection gauges
Annexes A and B of this part of ISO 11116 are for information only.
iv
---------------------- Page: 8 ----------------------
SIST EN ISO 11116-2:2000
©
ISO
ISO 11116-2:1999(E)
Introduction
This part of ISO 11116 belongs to a series of standards specifying thread dimensions and gauge requirements.
v
---------------------- Page: 9 ----------------------
SIST EN ISO 11116-2:2000
---------------------- Page: 10 ----------------------
SIST EN ISO 11116-2:2000
INTERNATIONAL STANDARD © ISO ISO 11116-2:1999(E)
Gas cylinders — 17E taper thread for connection of valves to gas
cylinders —
Part 2:
Inspection gauges
1 Scope
This part of ISO 11116 specifies types, dimensions and principles of the use of gauges, to be used in conjunction
with the taper thread specified in ISO 11116-2.
Annex A provides examples of calculations for thread gauge dimensions on the large end diameter.
Annex B draws attention to the limitations of the gauging system specified.
2 Terms and definitions
For the purposes of this part of ISO 11116 the following terms and definitions apply.
2.1
inspection gauge
gauge used for the routine gauging of cylinder neck and valve stem threads, but not used for checking other gauges
2.2
check gauge
gauge for checking dimensional conformity of inspection ring gauges, but not for gauging cylinder neck threads
2.3
single part gauge
gauge, plug or ring, plain or threaded of sufficient length to contact the full length of taper thread
2.4
two-part gauges
two separate inspection gauges, plug or ri
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.