EN ISO 10156:2017
(Main)Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2017)
Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2017)
ISO 10156:2017 specifies methods for determining whether or not a gas or gas mixture is flammable in air and whether a gas or gas mixture is more or less oxidizing than air under atmospheric conditions.
ISO 10156:2017 is intended to be used for the classification of gases and gas mixtures including the selection of gas cylinder valve outlets.
ISO 10156:2017 does not cover the safe preparation of these mixtures under pressure and at temperatures other than ambient.
Gasflaschen - Gase und Gasgemische - Bestimmung der Brennbarkeit und des Oxidationsvermögens zur Auswahl von Ventilausgängen (ISO 10156:2017)
Bouteilles à gaz - Gaz et mélanges de gaz - Détermination du potentiel d'inflammabilité et d'oxydation pour le choix des raccords de sortie de robinets (ISO 10156:2017)
L'ISO 10156:2017 spécifie des méthodes servant à déterminer si un gaz ou un mélange de gaz est ou non inflammable dans l'air et si un gaz ou un mélange de gaz est plus ou moins oxydant que l'air, dans les conditions atmosphériques.
L'ISO 10156:2017 est destiné à être utilisé pour la classification des gaz et des mélanges de gaz, y compris pour le choix des raccords de sortie de robinets de bouteilles à gaz.
L'ISO 10156:2017 ne traite pas de la préparation en toute sécurité de ces mélanges à une pression et à des températures autres que les conditions ambiantes.
Plinske jeklenke - Plini in zmesi plinov - Določitev stopnje vnetljivosti in oksidativnosti za izbiro izhodnega priključka ventila za jeklenko (ISO 10156:2017)
Ta dokument določa metode za ugotavljanje, ali je plin ali plinska zmes vnetljiva v zraku ali ne ter ali je plin oz. plinska zmes bolj ali manj oksidativna od zraka v atmosferskih pogojih.
Ta dokument je predviden za uporabo pri klasifikaciji plinov in plinskih zmesi, vključno z izbiro izhodnih odprtin ventilov plinskih jeklenk.
Ta dokument ne obsega varne priprave teh zmesi pod tlakom in pri temperaturah, ki niso okoljska temperatura.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10156:2018
01-maj-2018
1DGRPHãþD
SIST EN ISO 10156:2010
SIST EN ISO 10156:2010/AC:2010
3OLQVNHMHNOHQNH3OLQLLQ]PHVLSOLQRY'RORþLWHYVWRSQMHYQHWOMLYRVWLLQ
RNVLGDWLYQRVWL]DL]ELURL]KRGQHJDSULNOMXþNDYHQWLOD]DMHNOHQNR ,62
Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing
ability for the selection of cylinder valve outlets (ISO 10156:2017)
Gasflaschen - Gase und Gasgemische - Bestimmung der Brennbarkeit und des
Oxidationsvermögens zur Auswahl von Ventilausgängen (ISO 10156:2017)
Bouteilles à gaz - Gaz et mélanges de gaz - Détermination du potentiel d'inflammabilité
et d'oxydation pour le choix des raccords de sortie de robinets (ISO 10156:2017)
Ta slovenski standard je istoveten z: EN ISO 10156:2017
ICS:
23.020.35 Plinske jeklenke Gas cylinders
71.100.20 Industrijski plini Gases for industrial
application
SIST EN ISO 10156:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10156:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 10156:2018
EN ISO 10156
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2017
EUROPÄISCHE NORM
ICS 23.020.35; 71.100.20 Supersedes EN ISO 10156:2010
English Version
Gas cylinders - Gases and gas mixtures - Determination of
fire potential and oxidizing ability for the selection of
cylinder valve outlets (ISO 10156:2017)
Bouteilles à gaz - Gaz et mélanges de gaz - Gasflaschen - Gase und Gasgemische - Bestimmung der
Détermination du potentiel d'inflammabilité et Brennbarkeit und des Oxidationsvermögens zur
d'oxydation pour le choix des raccords de sortie de Auswahl von Ventilausgängen (ISO 10156:2017)
robinets (ISO 10156:2017)
This European Standard was approved by CEN on 19 August 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10156:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10156:2018
EN ISO 10156:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10156:2018
EN ISO 10156:2017 (E)
European foreword
This document (EN ISO 10156:2017) has been prepared by Technical Committee ISO/TC 58 “Gas
cylinders” in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2018, and conflicting national standards
shall be withdrawn at the latest by February 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10156:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.