CEN/TR 14548:2003
(Main)Adhesives - Guide to test methods and other standards for the general requirements, characterization and safety of structural adhesives
Adhesives - Guide to test methods and other standards for the general requirements, characterization and safety of structural adhesives
This Report identifies and categorizes the European and international standard used to determine the general requirements, characterization and safety of structural adhesives.
Klebstoffe - Anleitung zur Anwendung von Prüfverfahren und anderen Normen für allgemeine Anforderungen, Charakterisierung und Sicherheit von Strukturklebstoffen
Adhésifs - Guide des méthodes d'essai et d'autres normes pour les spécifications générales, la caractérisation et la sécurité des adhésifs structuraux
Lepila – Vodilo za preskusne metode in druge standarde za splošne zahteve, lastnosti in varnost konstrukcijskih lepil
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2003
Lepila – Vodilo za preskusne metode in druge standarde za splošne zahteve,
lastnosti in varnost konstrukcijskih lepil
Adhesives - Guide to test methods and other standards for the general requirements,
characterization and safety of structural adhesives
Klebstoffe - Anleitung zur Anwendung von Prüfverfahren und anderen Normen für
allgemeine Anforderungen, Charakterisierung und Sicherheit von Strukturklebstoffen
Adhésifs - Guide des méthodes d'essai et d'autres normes pour les spécifications
générales, la caractérisation et la sécurité des adhésifs structuraux
Ta slovenski standard je istoveten z: CEN/TR 14548:2003
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL REPORT
CEN/TR 14548
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
September 2003
ICS 83.180
English version
Adhesives – Guide to test methods and other standards for the
general requirements, characterization and safety of structural
adhesives
Adhésifs – Guides des méthodes d’essai et d’autres Klebstoffe – Anleitung zur Anwendung von Prüfverfahren
normes pour les spécifications générales, la caractérisation und anderen Normen für allgemeine Anforderungen,
et la sureté des adhésifs structuraux Charakterisierung und Sicherheit von Strukturklebstoffen
This Technical Report was approved by CEN on 2 January 2003. It has been drawn up by the Technical Committee CEN/TC 193.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 14548:2003 E
worldwide for CEN national Members.
Contents Page
Foreword. 3
1 Scope . 4
2 References. 4
3 Terms and definitions. 7
4 Categorisation of test methods and other standards . 7
5 Examination and preparation of samples . 7
6 Category I: General methods for qualitative and/or quantitative assessment. 7
6.1 Adhesives . 7
6.2 Substrates. 8
6.2.1 Surface preparation . 8
6.2.2 Surface assessment . 8
6.3 Assemblies . 9
7 Category II: Characterisation methods to obtain quantitative design values . 9
7.1 Adhesives . 9
7.2 Substrates. 10
7.2.1 Surface preparation . 10
7.2.2 Surface assessment . 10
7.3 Assemblies . 10
8 Category III: Methods and standards related to safety, storage and product life. 10
Foreword
This document (CEN/TR 14548:2003) has been prepared by Technical Committee CEN/TC 193 “Adhesives”,
the secretariat of which is held by AENOR.
1 Scope
This Technical Report identifies and categorises the European and International Standards relating to
structural adhesives. It encompasses the methods used to both prepare and assess surfaces and to
determine the general characteristics of structural adhesives. Additionally, it provides methods for gauging the
performance of structural adhesives under load and the means of obtaining design data. Standards relating to
safety, storage and product life are also provided.
NOTE In this Technical Report safety does not refer to the mechanical integrity of bonded joints.
2 References
This Technical Report incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed hereafter.
For dated references, subsequent amendments to or revisions of any of these publications apply to this
Technical Report only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies (including amendments).
EN 542, Adhesives - Determination of density.
EN 543, Adhesives - Determination of apparent density of powder and granule adhesives.
EN 827, Adhesives - Determination of conventional solids content and constant mass solids content .
EN 828, Adhesives - Wettability - Determination by measurement of contact angle and critical surface tension
of solid surface.
EN 923:1998, Adhesives - Terms and definitions.
EN 924, Adhesives - Solvent-borne and solvent-free adhesives - Determination of flashpoint.
EN 1066, Adhesives - Sampling.
EN 1067, Adhesives - Examination and preparation of samples for testing.
EN 1239, Adhesives - Freeze-thaw stability.
EN 1244, Adhesives - Determination of the colour and/or colour changes of adhesive coats under the
influence of light.
EN 1245, Adhesives - Determination of pH - Test method.
EN 1464, Adhesives - Determination of peel resistance of high-strength adhesive bonds - Floating roller
method (ISO 4578:1990 modified)
EN 1465, Adhesives - Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies (ISO
4578:1990 modified)
EN 1965-1, Structural adhesives - Corrosion - Part 1 : Determination and classification of corrosion to a
copper substrate.
EN 1965-2, Structural adhesives - Corrosion - Part 2 : Determination and classification of corrosion to a brass
substrate.
EN 1966, Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three
point bending method.
EN 1967, Structural adhesives - Evaluation of the effectiveness of surface treatment techniques for aluminium
using a wet peel test in association with the floating roller method.
EN 2101, Aerospace series - Chromic acid anodizing of aluminium and wrought aluminium alloys.
prEN 2243-1, Aerospace series - Structural adhesives - Test methods - Part 1: Single lap shear
EN 2243-2, Aerospace series - Structural adhesives - Test methods - Part 2: Peel metal-metal.
EN 2243-5, Aerospace series – Structural adhesives - Test methods – Part 5: Ageing tests
prEN 2243-6, Structural adhesives - Test methods - Part 6: Single lap shear-thick adherend (shear stress and
shear displacement .
EN 2334, Aerospace series - Chromic-sulphuric acid pickle of aluminium and aluminium alloys.
EN 2497, Aerospace series – Dry abrasive blasting of titanium and titanium alloys.
EN 2667, Aerospace series - Non-metallic materials; foaming structural adhesives, Test methods.
prEN 3002, Aerospace series - Chromic acid anodizing - Testing of adhesives.
prEN 3003, Structural adhesives – Test method for the determination of mass per unit area of film adhesives.
prEN 4106, Aerospace series - Non metallic materials - Structural adhesive system - Paste adhesive -
Technical specification.
prEN 6040, Aerospace series - Non-metallic materials - Test method - Analysis of thermoset systems by H
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.