EN ISO 10642:2004
(Main)Hexagon socket countersunk head screws (ISO 10642:2004)
Hexagon socket countersunk head screws (ISO 10642:2004)
ISO 10642:2004 specifies the characteristics of hexagon socket countersunk head screws with threads from M3 up to and including M20, with product grade A and property classes 8.8, 10.9 and 12.9.
Senkschrauben mit Innensechskant (ISO 10642:2004)
Diese Internationale Norm legt die Eigenschaften von metrischen Senkschrauben mit Innensechskant mit
Gewinden von M3 bis einschließlich M20 in Produktklasse A und mit Festigkeitsklasse 8.8, 10.9 und 12.9 fest.
ANMERKUNG Es wird besonders auf die Fußnote in Tabelle 2 und auf Tabelle 3 bezüglich der Einschränkung der Mindestbruchkraft hingewiesen.
Werden in besonderen Fällen andere Festlegungen als die in der vorliegenden Internationalen Norm benötigt, so sollten diese den bestehenden Internationalen Normen entnommen werden, z. B. ISO 261, ISO 888, ISO 898-1, ISO 965-2 und ISO 4759-1.
Vis à tête fraisée à six pans creux (ISO 10642:2004)
L'ISO 10642:2004 spécifie les caractéristiques des vis à tête fraisée à six pans creux de filetage M3 à M20 inclus, de grade A et de classes de qualité 8.8, 10.9 et 12.9.
Vijaki z ugrezno glavo in notranjim šestkotnikom (ISO 10642:2004)
Ta mednarodni standard določa značilnosti vijakov z ugrezno glavno in notranjim šestkotnikom z navoji od M3 do vključno M20 ter z razredom izdelave A in razredi trdnosti 8,8, 10,9 in 12,9.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Vijaki z ugrezno glavo in notranjim šestkotnikom (ISO 10642:2004)Senkschrauben mit Innensechskant (ISO 10642:2004)Vis a tete fraisée a six pans creux (ISO 10642:2004)Hexagon socket countersunk head screws (ISO 10642:2004)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN ISO 10642:2004SIST EN ISO 10642:2004en01-september-2004SIST EN ISO 10642:2004SLOVENSKI
STANDARDSIST EN ISO 10642:20011DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 10642March 2004ICS 21.060.10Supersedes EN ISO 10642:1997English versionHexagon socket countersunk head screws (ISO 10642:2004)Vis à tête fraisée à six pans creux (ISO 10642:2004)Senkschrauben mit Innensechskant (ISO 10642:2004)This European Standard was approved by CEN on 16 January 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 10642:2004 ESIST EN ISO 10642:2004
INTERNATIONALSTANDARDISO10642Second edition2004-03-01Reference numberISO10642:2004(E)© ISO2004Hexagon socket countersunk head screwsVis à tête fraisée à six pans creux
ISO10642:2004(E)ii© ISO2004–All rights reservedPDF disclaimerThis PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shallnot be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Indownloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariataccepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creationparameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In theunlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.©ISO2004All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below orISO's member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.+ 41 22 749 01 11Fax+ 41 22 749 09 47E-mailcopyright@iso.orgWebwww.iso.orgPublished in SwitzerlandSIST EN ISO 10642:2004
ISO10642:2004(E)© ISO2004–All rights reservediiiContents Page1Scope . 12Normative references . 13Dimensions and gauging of head . 24Requirements and reference International Standards . 65Designation . 7SIST EN ISO 10642:2004
ISO10642:2004(E)iv© ISO2004–All rights reservedForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75% of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.ISO10642 was prepared by Technical Committee ISO/TC2, Fasteners.This second edition cancels and replaces the first edition (ISO10642:1997), which has been technicallyrevised.SIST EN ISO 10642:2004
INTERNATIONAL STANDARDISO10642:2004(E)© ISO2004–All rights reserved1Hexagon socket countersunk head screws1ScopeThis International Standard specifies the characteristics of hexag
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.