iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1569:1999

(Main)

Surfaces for sports areas - Determination of the behaviour under a rolling load

Surfaces for sports areas - Determination of the behaviour under a rolling load

This European Standard specifies a method for the determination of behaviour under a rolling load of indoor sports surfaces.

Sportböden - Bestimmung des Verhaltens bei rollender Last

Diese Europäische Norm legt ein Verfahren zur Bestimmung des Verhaltens von einigen Sporthallenböden bei rollender Last fest.

Sols sportifs - Détermination du comportement sous charge roulante

La présente norme européenne prescrit une méthode de détermination du comportement sous charge roulante de certains sols sportifs.

Podloge za športne dejavnosti – Ugotavljanje obnašanja pri kotalni obremenitvi

General Information

Status
Withdrawn
Publication Date
17-Aug-1999
Withdrawal Date
05-May-2020
ICS
97.220.10 - Sports facilities
Technical Committee
CEN/TC 217 - Surfaces for sport areas
Drafting Committee
CEN/TC 217/WG 2 - Surfaces of sports halls
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
06-May-2020
Ref Project
SIST EN 1569:2002 - Surfaces for sports areas - Determination of the behaviour under a rolling load

Relations

Replaced By
EN 1569:2020 - Surfaces for sports areas - Determination of the behaviour under a rolling load
Effective Date
11-May-2020

Buy Standard

EN 1569:2002EN 1569:2002
PreviousNext
Standard
EN 1569:2002
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Podloge za športne dejavnosti – Ugotavljanje obnašanja pri kotalni obremenitviSportböden - Bestimmung des Verhaltens bei rollender LastSols sportifs - Détermination du comportement sous charge roulanteSurfaces for sports areas - Determination
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12230:2023(Main)
Surfaces for sports areas - Test method for the determination of tensile properties of synthetic sports surfaces
SIST EN 12230:2023

This document specifies three methods for the determination of the tensile properties of materials used as surfaces, elastic layers and shockpads for sports areas.
Method 1 measures the tensile strength of homogenous test specimens that are less than 25 mm in thickness.
Method 2 measures the transversal tensile strength of homogenous test specimens that are more than 25 mm in thickness.
Method 3 measures the tensile strength of sports surfaces or shockpads that are non-homogenous and contain slots or grooves cut into their structure.
This document is applicable both to prefabricated sheet materials and to materials formed by casting of liquid systems cured in-situ.
If the nature of the sports surface is such that a properly representative test piece cannot be prepared in the manner described in this document, then determination of tensile properties should not be attempted for quality control purposes, or as a predictor of performance in use. With such materials, it can be more appropriate to determine their compressive properties or other dynamic characteristics for these purposes.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12616:2023(Main)
Surfaces for sports areas - Test methods for the determination of vertical water infiltration and horizontal water flow rates
SIST EN 12616:2023

This document has two parts.
Part 1 specifies four methods for the determination of the vertical water infiltration rate of different types of sports surfacing.
Method A is suitable for measuring the vertical water infiltration rate of synthetic, textile and synthetic turf sports surfaces in the laboratory.
Method B is suitable for on-site measurements of the Vertical Water Infiltration Rate of synthetic, textile, synthetic turf and bound mineral sports surfaces.
Method C is suitable for on-site measurements of the vertical water infiltration rate of natural turf sports surfaces.
Method D is suitable for measuring the for on-site measurements of the vertical water infiltration rate of unbound mineral sports surfaces.
NOTE For filled synthetic turf and unbound mineral surfaces, laboratory tests are considered to give a more precise indication of how a surface will perform.
Part 2 specifies a method for determining the horizontal water flow rate of synthetic, textile and synthetic turf surfaces in the laboratory.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15330-4:2022(Main)
Surfaces for sports areas - Synthetic turf and needle-punched surfaces primarily designed for outdoor use - Part 4: Specification for shockpads used with synthetic turf, needle-punch and textile sports surfaces
SIST EN 15330-4:2023

This document specifies minimum performance and durability requirements for shockpads used within synthetic turf and textile sports surfacing systems.
The document also specifies appropriate performance tolerance for production and on-site quality control procedures.
This document does not cover structural properties of shockpads. Where appropriate, compliance with other European or national standards and guidelines for these aspects should be followed.
NOTE 1 The sports performance characteristics of a sports surfacing system are provided by the combined characteristics of the playing surface, any infill within the playing surface and the shockpad. The selection of the correct combination of each is complex and the responsibility of the sports surface system designer. It is important to take this into account when considering the performance of a shockpad. A shockpad alone is not be expected to satisfy the performance requirements of the complete sports surfacing system as specified in EN 15330-1, E, etc.
NOTE 2 Some forms of innovative shockpad are designed to provide additional functions beyond aiding the provision of the required sports performance properties. Some of these additional functions can, by design, mean that full compliance with all requirements of this document is not appropriate.
NOTE 3 This document only refers to the shockpad. It makes no recommendations on sub-base constructions or the different synthetic turf for needle-punch textile sports surface designs.
NOTE 4 Annex E (informative) can be used in those countries where national guidance or regulations are not available. If such guidance or regulations are available, they supersede Annex E.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17467:2022(Main)
Surfaces for sports areas - Test method for the determination of the residual deformation of synthetic or organic infill granules after static load
SIST EN 17467:2022

This document specifies a test method for the determination of the residual deformation and visual inspection of synthetic or organic granules used in synthetic turf for sports surfaces after static load.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17435:2021(Main)
Surfaces for sports areas - Test method for the determination of Head Injury Criterion (HIC) and Critical Fall Height (CFH)
SIST EN 17435:2022

This document specifies test methods for measuring the impact attenuation of sports surfaces. Three different methods are specified. In Procedure A, a series of tests are undertaken from differing drop heights and the HIC values are plotted, and the Critical Fall Height determined. In Procedure B, a single test is undertaken from differing drop heights and the HIC values are plotted, and the Critical Fall Height determined. In Procedure C a series of tests are made at a fixed drop height and the maximum value of HIC is calculated.
This test method is primarily intended for use on both natural and synthetic turf sport surfaces. It may be carried out in a laboratory on test specimens or in situ on installed sports surfaces. This test method may not be suitable for sports surfaces covered by EN 14904.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17519:2020(Main)
Surfaces for sports areas - Synthetic turf sports facilities - Guidance on how to minimize infill dispersion into the environment
SIST-TP CEN/TR 17519:2020

This document describes ways of containing infill materials used in many types of synthetic turf sports fields within the confines of the sports field, so they are not dispersed into the surrounding environment.
The options described are based on examples of best practice identified by members of CEN/TC 217.
This document is intended to be of practical use, to create awareness amongst field designers, venue owners, installation companies and those maintaining synthetic turf sports fields. It is applicable for all forms of synthetic turf sports field, from those used for community activities to those used by professional and elite level athletes.

  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17409:2020(Main)
Surfaces for sports areas - Code of practice for the sampling of performance infills used within synthetic turf surfaces
SIST EN 17409:2020

This document specifies the minimum procedures for the sampling of performance infills used within synthetic turf surfaces to verify compliance with toxicology, environmental and performance regulations and standards.
Four sampling procedures are specified:
Method 1 specifies how to take samples during production of the infill material.
Method 2 specifies how to take samples from big bags delivered to site.
Method 3 specifies how to take samples from small bags delivered to site.
Method 4 specifies a procedure for taking samples from a synthetic turf (e.g. sports, recreational or landscaping surface).
The procedures specified are suitable for all forms of infill.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1517:2020(Main)
Surfaces for sports areas - Determination of resistance to impact
SIST EN 1517:2020

This document specifies a method for the determination of resistance to impact of sports floor systems. It is primarily designed to be used on surfaces intended for use in indoor sports halls. The test can be undertaken in the laboratory or on site.
When undertaking tests on site, it is important to note that permanent damage to the sports floor can be caused.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17324:2020(Main)
Surfaces for sports areas - Test method for the determination of the resistance to dynamic fatigue of shock pads and sports surfaces
SIST EN 17324:2020

This document specifies a method of test for the determination of resistance to dynamic fatigue of shockpads (including elastic layers) used in synthetic turf surfacing systems. It can also be used on other types and complete forms of sports surfacing systems.
The test is undertaken on test specimens in the laboratory.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1569:2020(Main)
Surfaces for sports areas - Determination of the behaviour under a rolling load
SIST EN 1569:2020

This document specifies a method of test for the determination of behaviour under a rolling load of certain surfaces for sports areas. It is suitable for tests undertaken in the laboratory and on site.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day