EN ISO 544:2017
(Main)Welding consumables - Technical delivery conditions for filler materials and fluxes - Type of product, dimensions, tolerances and markings (ISO 544:2017)
Welding consumables - Technical delivery conditions for filler materials and fluxes - Type of product, dimensions, tolerances and markings (ISO 544:2017)
ISO 544:2017 specifies technical delivery conditions for filler materials and fluxes for fusion welding.
ISO 544:2017 does not apply to other auxiliary materials such as shielding gases.
Schweißzusätze - Technische Lieferbedingungen für Schweißzusätze und Pulver - Art des Produktes, Maße, Grenzabmaße und Kennzeichnung (ISO 544:2017)
Dieses Dokument legt technische Lieferbedingungen für Schweißzusätze und Pulver zum Schmelz-schweißen fest.
Dieses Dokument gilt nicht für andere Schweißhilfsstoffe wie Schutzgase.
Produits consommables pour le soudage - Conditions techniques de livraison des produits d'apport et des flux - Type de produits, dimensions, tolérances et marquage (ISO 544:2017)
ISO 544:2017 spécifie les conditions techniques de livraison des produits d'apport et des flux utilisés pour le soudage par fusion.
ISO 544:2017 ne s'applique pas aux autres produits consommables auxiliaires, tels que les gaz de protection.
Dodajni materiali za varjenje - Tehnični dobavni pogoji za dodajne materiale in praške - Vrsta izdelka, izmere, tolerance in označevanje (ISO 544:2017)
Ta dokument določa tehnične dobavne pogoje za dodajne materiale in talila za talilno varjenje.
Ta dokument se ne uporablja za druge dodatne materiale, kot so zaščitni plini.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2018
1DGRPHãþD
SIST EN ISO 544:2011
'RGDMQLPDWHULDOL]DYDUMHQMH7HKQLþQLGREDYQLSRJRML]DGRGDMQHPDWHULDOHLQ
SUDãNH9UVWDL]GHONDL]PHUHWROHUDQFHLQR]QDþHYDQMH ,62
Welding consumables - Technical delivery conditions for filler materials and fluxes - Type
of product, dimensions, tolerances and markings (ISO 544:2017)
Schweißzusätze - Technische Lieferbedingungen für Schweißzusätze und Pulver - Art
des Produktes, Maße, Grenzabmaße und Kennzeichnung (ISO 544:2017)
Produits consommables pour le soudage - Conditions techniques de livraison des
produits d'apport et des flux - Type de produits, dimensions, tolérances et marquage
(ISO 544:2017)
Ta slovenski standard je istoveten z: EN ISO 544:2017
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 544
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2017
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 544:2011
English Version
Welding consumables - Technical delivery conditions for
filler materials and fluxes - Type of product, dimensions,
tolerances and markings (ISO 544:2017)
Produits consommables pour le soudage - Conditions Schweißzusätze - Technische Lieferbedingungen für
techniques de livraison des produits d'apport et des Schweißzusätze und Pulver - Art des Produktes, Maße,
flux - Type de produits, dimensions, tolérances et Grenzabmaße und Kennzeichnung (ISO 544:2017)
marquage (ISO 544:2017)
This European Standard was approved by CEN on 3 November 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 544:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 544:2017) has been prepared by Technical Committee ISO/TC 44 “Welding and
allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be
withdrawn at the latest by June 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 544:2011.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 544:2017 has been approved by CEN as EN ISO 544:2017 without any modification.
INTERNATIONAL ISO
STANDARD 544
Fifth edition
2017-11
Welding consumables — Technical
delivery conditions for filler materials
and fluxes — Type of product,
dimensions, tolerances and markings
Produits consommables pour le soudage — Conditions techniques
de livraison des produits d'apport et des flux — Type de produits,
dimensions, tolérances et marquage
Reference number
ISO 544:2017(E)
©
ISO 2017
ISO 544:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 544:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Product type and welding process . 1
5 Dimensions and tolerances . 1
5.1 Solid wires and solid wire electrodes, tubular cored wires and tubular cored
electrodes, solid and tubular cored rods and covered electrodes . 1
5.2 Solid strip electrodes . 2
5.3 Cored strip electrodes and thin foils . 2
5.4 Fluxes . 4
6 Rounding procedure . 4
7 Condition of welding consumables . 4
7.1 Covered electrodes . 4
7.2 Wires, rods, and strips . 4
8 Marking . 8
8.1 Marking on the product . 8
8.1.1 Covered electrodes . 8
8.1.2 Wires and strips . 8
8.1.3 Rods . . 8
8.2 Marking on the package . 8
9 Packaging . 8
10 Inspection documents . 9
Bibliography .10
ISO 544:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see http://www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see http://www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: http://www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 3, Welding consumables.
This fifth edition cancels and replaces the fourth edition (ISO 544:2011), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— in 5.4, clarification that fluxes can be obtainable in different particle size distributions is given (not
all fluxes are available in multiple particle size distributions);
— Table 2 has been changed;
— in Table 4, a new spool type B400 has been added;
— 8.1.2 has been revised to include reels and rims
— 8.2, bullet number 5 has been revised.
Requests for official interpretations of any aspect of this document should be directed to the Secretariat
of ISO/TC 44/SC 3 via your national standards body. A complete listing of these bodies can be found at
http://www.iso.org.
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 544:2017(E)
Welding consumables — Technical delivery conditions for
filler materials and fluxes — Type of product, dimensions,
tolerances and markings
1 Scope
This document specifies technical delivery conditions for filler materials and fluxes for fusion welding.
This document does not apply to other auxiliary materials such as shielding gases.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the e
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.