EN ISO 4210-3:2014
(Main)Cycles - Safety requirements for bicycles - Part 3: Common test methods (ISO 4210-3:2014)
Cycles - Safety requirements for bicycles - Part 3: Common test methods (ISO 4210-3:2014)
ISO 4210-3:2014 specifies the common test methods for ISO 4210‑2.
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 3: Allgemeine Prüfverfahren (ISO 4210-3:2014)
Der vorliegende Teil von ISO 4210 legt die allgemeinen Prüfverfahren nach ISO 4210-2 fest.
Cycles - Exigences de sécurité des bicyclettes - Partie 3: Méthodes d'essai communes (ISO 4210-3:2014)
ISO 4210-3:2014 spécifie les méthodes d'essai communes pour l'ISO 4210‑2.
Kolesa - Varnostne zahteve za kolesa - 3. del: Splošne preskusne metode (ISO 4210-3:2014)
Standard EN ISO 4210 določa splošne preskusne metode za standard ISO 4210-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2014
1DGRPHãþD
SIST EN 14764:2006
SIST EN 14766:2006
SIST EN 14781:2006
Kolesa - Varnostne zahteve za kolesa - 3. del: Splošne preskusne metode (ISO
4210-3:2014)
Cycles - Safety requirements for bicycles - Part 3: Common test methods (ISO 4210-
3:2014)
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 3: Allgemeine
Prüfverfahren (ISO 4210-3:2014)
Cycles - Exigences de sécurité des bicyclettes - Partie 3: Méthodes d'essai communes
(ISO 4210-3:2014)
Ta slovenski standard je istoveten z: EN ISO 4210-3:2014
ICS:
43.150 Kolesa Cycles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 4210-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 43.150 Supersedes EN 14764:2005, EN 14766:2005, EN
14781:2005
English Version
Cycles - Safety requirements for bicycles - Part 3: Common test
methods (ISO 4210-3:2014)
Cycles - Exigences de sécurité des bicyclettes - Partie 3: Fahrräder - Sicherheitstechnische Anforderungen an
Méthodes d'essai communes (ISO 4210-3:2014) Fahrräder - Teil 3: Allgemeine Prüfverfahren (ISO 4210-
3:2014)
This European Standard was approved by CEN on 21 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4210-3:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 4210-3:2014) has been prepared by Technical Committee ISO/TC 149 "Cycles" in
collaboration with Technical Committee CEN/TC 333 “Cycles” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2015, and conflicting national standards shall be withdrawn at
the latest by July 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14764:2005, EN 14766:2005, EN 14781:2005.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4210-3:2014 has been approved by CEN as EN ISO 4210-3:2014 without any modification.
INTERNATIONAL ISO
STANDARD 4210-3
First edition
2014-07-01
Cycles — Safety requirements for
bicycles —
Part 3:
Common test methods
Cycles — Exigences de sécurité des bicyclettes —
Partie 3: Méthodes d’essai communes
Reference number
ISO 4210-3:2014(E)
©
ISO 2014
ISO 4210-3:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 4210-3:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test methods . 1
4.1 Brake tests and strength tests . 1
4.2 Front mudguard test methods . 2
4.3 Road test on a fully assembled bicycle test methods . 4
4.4 Durability test of marking . 4
4.5 Fatigue test . 5
4.6 Fatigue test for composite components . 5
4.7 Impact test . 5
4.8 Plastic material test ambient temperature . 5
Annex A (informative) Structural integrity of the fully assembled bicycle .6
Annex B (informative) Verification of free-fall velocity . 8
Bibliography . 9
ISO 4210-3:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 149, Cycles, Subcommittee SC 1, Cycles and major
sub-assemblies.
This first edition of ISO 4210-3, together with ISO 4210-1, ISO 4210-2, ISO 4210-4, ISO 4210-5, ISO 4210-6,
ISO 4210-7, ISO 4210-8, and ISO 4210-9, cancels and replaces ISO 4210:1996, which has been technically
revised.
ISO 4210 consists of the following parts, under the general title Cycles — Safety requirements for bicycles:
— Part 1: Terms and definitions
— Part 2: Requirements for city and trekking, young adult, mountain and racing bicycles
— Part 3: Common test methods
— Part 4: Braking test methods
— Part 5: Steering test methods
— Part 6: Frame and fork test methods
— Part 7: Wheels and rims test methods
— Part 8: Pedals and drive system test methods
— Part 9: Saddles and seat-post test methods
iv © ISO 2014 – All rights reserved
ISO 4210-3:2014(E)
Introduction
This International Standard was developed in response to a demand throughout the world. The aim is to
ensure that bicycles manufactured in compliance with this International Standard will be as safe as is
practically possible. The tests are designed to ensure the strength and durability of individual parts as
well as of the bicycle as a whole, demanding high quality throughout and consideration of safety aspects
from the design stage onwards.
The scope is limited to safety considerations, and has specifically avoided standardization of components.
If the bicycle is to be used on public roads, national regulations apply.
INTERNATIONAL STANDARD ISO 4210-3:2014(E)
Cycles — Safety requirements for bicycles —
Part 3:
Common test methods
1 Scope
This part of ISO 4210 specifies the common test methods for ISO 4210-2.
2 Normative references
The following referenced documents, in whole or in part, are normatively referenced in this document
and are indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4210-1, Cycles — Safety requirements for bicycles — Part 1: Terms and definitions
ISO 4210-2:2014, Cycles — Safety requirements for bicycles — Part 2: Requirements for city and trekking,
young adult, mountain and racing bicycles
ISO 4210-4:2014, Cycles — Safety requirements for bicycles — Part 4: Braking test methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4210-1 apply.
4 Test methods
4.1 Brake tests and strength tests
4.1.1 Definition of brake tests
Brake tests to which accuracy requirements apply, as in 4.1.4, are those specified in ISO 4210-2:2014,
4.6.3 to 4.6.6, ISO 4210-4:2014, 4.2, and ISO 4210-4:2014, 4.6.3.3.
4.1.2 Definition of strength tests
Strength tests to which accuracy requirements apply, as in 4.1.4, are those involving static, impact, or
fatigue loading as specified in ISO 4210-2:2014, 4.7 to 4.13, ISO 4210-2:2014, 4.16, and ISO 4210-2:2014,
4.20.2.
4.1.3 Numbers and condition of specimens for the strength tests
In general, for static, impact, and fatigue tests, each test shall be conducted on a new test sample, but if
only one sample is available, it is permissible to conduct a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.