Road vehicles - Connections for on-board electrical wiring harnesses - Part 2: Definitions, test methods and general performance requirements (ISO 8092-2:2005)

ISO 8092:2005 defines terms and specifies test methods and general performance requirements for single-pole and multi-pole connections used with on-board electrical wiring harnesses of road vehicles.
It is applicable to connectors designed to be disconnected after mounting in the vehicle for repair and maintenance only. It does not cover one-part connections, i.e. where one part of the connection has direct contact to the pattern of the printed circuit board.
ISO 8092:2005 is not applicable to internal connections of electronic devices.

Straßenfahrzeuge - Steckverbindungen für das elektrische Fahrzeug-Bordnetz - Teil 2: Begriffe, Prüfungen und allgemeine Anforderungen (ISO 8092-2:2005)

Dieser Teil von ISO 8092 definiert Begriffe und legt Prüfverfahren und allgemeine Anforderungen an ein- und mehrpolige Steckverbindungen fest, die in elektrischen Bordnetzen von Straßenfahrzeugen verwendet werden.
Dieser Teil von ISO 8092 ist auf Steckverbinder anwendbar, die nach der Montage im Fahrzeug ausschließlich im Reparaturfall und/oder beim Kundendienst getrennt werden. Er schließt einteilige Steckverbindungen aus, d.h. bei denen ein Teil der Steckverbindung direkten Kontakt mit den Leiterbahnen gedruckter Schaltungen hat.
Dieser Teil von ISO 8092 gilt nicht für Steckverbindungen in elektronischen Geräten.

Véhicules routiers - Connexions pour faisceaux de câblage électriques embarqués - Partie 2: Définitions, méthodes d'essai et exigences de performances générales (ISO 8092-2:2005)

L'ISO 8092-2:2005 donne les définitions et spécifie les méthodes d'essai ainsi que les exigences de performance générales relatives aux connexions unipolaires et multipolaires pour des faisceaux de câblage électriques embarqués destinés aux véhicules routiers.
L'ISO 8092-2:2005 est applicable aux connecteurs qui, une fois montés dans le véhicule, ne sont conçus pour être débranchés que pour les besoins de réparation et/ou de maintenance. Elle ne couvre pas les connexions à une seule partie, c'est-à-dire les connexions dont une partie est en contact direct avec les pistes de la carte à circuit imprimé.
L'ISO 8092-2:2005 n'est pas applicable aux connexions internes des dispositifs électroniques.

Cestna vozila – Priključki za električno opremo, vgrajeni na armaturi vozila – 2. del: Definicije, preskusne metode in splošne zahtevane lastnosti (ISO 8092-2:2005)

General Information

Status
Withdrawn
Publication Date
30-Nov-2005
Withdrawal Date
01-Aug-2023
Technical Committee
Drafting Committee
Current Stage

Relations

Buy Standard

Standard
EN ISO 8092-2:2006
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2006
&HVWQDYR]LOD±3ULNOMXþNL]DHOHNWULþQRRSUHPRYJUDMHQLQDDUPDWXULYR]LOD±GHO
'HILQLFLMHSUHVNXVQHPHWRGHLQVSORãQH]DKWHYDQHODVWQRVWL ,62
Road vehicles - Connections for on-board electrical wiring harnesses - Part 2:
Definitions, test methods and general performance requirements (ISO 8092-2:2005)
Straßenfahrzeuge - Steckverbindungen für das elektrische Fahrzeug-Bordnetz - Teil 2:
Begriffe, Prüfungen und allgemeine Anforderungen (ISO 8092-2:2005)
Véhicules routiers - Connexions pour faisceaux de câblage électriques embarqués -
Partie 2: Définitions, méthodes d'essai et exigences de performances générales (ISO
8092-2:2005)
Ta slovenski standard je istoveten z: EN ISO 8092-2:2005
ICS:
43.040.10 (OHNWULþQDLQHOHNWURQVND Electrical and electronic
RSUHPD equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 8092-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 43.040.10 Supersedes EN ISO 8092-2:2001
English Version
Road vehicles - Connections for on-board electrical wiring
harnesses - Part 2: Definitions, test methods and general
performance requirements (ISO 8092-2:2005)
Véhicules routiers - Connexions pour faisceaux de câblage Straßenfahrzeuge - Steckverbindungen für das elektrische
électriques embarqués - Partie 2: Définitions, méthodes Fahrzeug-Bordnetz - Teil 2: Begriffe, Prüfungen und
d'essai et exigences de performances générales (ISO allgemeine Anforderungen (ISO 8092-2:2005)
8092-2:2005)
This European Standard was approved by CEN on 4 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8092-2:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 8092-2:2005) has been prepared by Technical Committee ISO/TC 22
"Road vehicles" in collaboration with CMC.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.

This document supersedes EN ISO 8092-2:2001.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 8092-2:2005 has been approved by CEN as EN ISO 8092-2:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 8092-2
Fourth edition
2005-12-01
Road vehicles — Connections for
on-board electrical wiring harnesses —
Part 2:
Definitions, test methods and general
performance requirements
Véhicules routiers — Connexions pour faisceaux de câblage électriques
embarqués —
Partie 2: Définitions, méthodes d'essai et exigences de performances
générales
Reference number
ISO 8092-2:2005(E)
©
ISO 2005
ISO 8092-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 8092-2:2005(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Tests and requirements . 4
4.1 General. 4
4.2 Visual examination . 5
4.3 Connection and disconnection . 7
4.4 Tensile strength for crimped connections. 8
4.5 Locking device strength . 9
4.6 Contact insertion force. 9
4.7 Contact retention in housing. 9
4.8 Connection resistance (voltage drop) . 10
4.9 Influence of water . 12
4.10 Temperature / humidity cycling. 13
4.11 Combined temperature / vibration . 16
4.12 Insulation resistance. 18
4.13 Withstand voltage. 18
4.14 Temperature rise. 19
4.15 Connector coding and polarisation . 21
4.16 Salt spray. 21
4.17 Current cycling. 21
4.18 Thermal ageing. 21
4.19 Mechanical shock. 22
4.20 Drop. 22
4.21 Dust. 23
4.22 Rapid change of temperature (thermal shock) .24
4.23 Chemical fluids . 24
4.24 Flowing gas corrosion test . 25
Annex A (normative) Additional cable dimensions . 26
Annex B (informative) Cable attachment by insulation-displacement connection (IDC) — Bending
test. 27
Bibliography . 29

ISO 8092-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8092-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical
and electronic equipment.
This fourth edition cancels and replaces the third edition (ISO 8092-2:2000), which has been technically
revised.
ISO 8092 consists of the following parts, under the general title Road vehicles — Connections for on-board
electrical wiring harnesses:
⎯ Part 1: Tabs for single-pole connections — Dimensions and specific requirements
⎯ Part 2: Definitions, test methods and general performance requirements
⎯ Part 3: Tabs for multi-pole connections — Dimensions and specific requirements
⎯ Part 4: Pins for single- and multi-pole connections — Dimensions and specific requirements

iv © ISO 2005 – All rights reserved

INTERNATIONAL STANDARD ISO 8092-2:2005(E)

Road vehicles — Connections for on-board electrical wiring
harnesses —
Part 2:
Definitions, test methods and general performance
requirements
1 Scope
This part of ISO 8092 defines terms, and specifies test methods and general performance requirements for
single-pole and multi-pole connections used with on-board electrical wiring harnesses of road vehicles.
This part of ISO 8092 is applicable to connectors designed to be disconnected after mounting in the vehicle
for repair and maintenance only. It does not cover one-part connections, i.e. where one part of the connection
has direct contact to the pattern of the printed circuit board.
This part of ISO 8092 is not applicable to internal connections of electronic devices.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1817; Rubber, vulcanized — Determination of the effect of liquids
ISO 3170; Petroleum liquids — Manual sampling
ISO 6722, Road vehicles — 60 V and 600 V single core cables — Dimensions, test methods and
requirements
ISO 7309, Road
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.