prEN 15080-15

Extended application of results from fire resistance tests - Part 15: Linear joint seals

To provide extended application (EXAP) rules and procedures for linear joint seals

Erweiterter Anwendungsbereich der Ergebnisse aus Feuerwiderstandsprüfungen - Teil 15: Abdichtungssysteme für Bauteilfugen

Die Zielsetzung dieses Dokuments ist die Formulierung von Grundprinzipien und Anleitungen für die Erarbeitung von Dokumenten zur erweiterten Anwendung von Versuchsergebnissen für Abdichtungssysteme von Bauteilfugen, die nach EN 1366 4 geprüft worden sind. Der Bereich des Dokuments zur erweiterten Anwendung gilt zusätzlich zum direkten Anwendungsbereich nach EN 1366 4 und kann auf einem einzigen Versuch oder mehreren Versuchen basieren, die die relevanten Informationen für eine erweiterte Anwendung liefern.
Es bleibt festzuhalten, dass diese Norm allgemeine Orientierungshilfen zu den wahrscheinlichen Auswirkungen einer Veränderung bietet. Sie liefert jedoch weder Angaben über die tatsächlichen Werte und das Ausmaß der Veränderung noch darüber wie diese Werte zu ermitteln sind.
Es bleibt weiter festzuhalten, dass zum gegenwärtigen Zeitpunkt von unzureichenden  Versuchsergebnissen und Prüferfahrung ausgegangen wird, um Regelungen für den erweiterten Anwendungsbereich von mechanisch wirkenden Abdichtungen aus Metall festzulegen. Alle entsprechenden Entwürfe und Gestaltungsansätze müssen daher Gegenstand eines dafür geeigneten Versuchsprogramms sein.

Application étendue des résultats des essais de résistance au feu - Partie 15: Calfeutrements de joints linéaires

Le présent document a pour objectif de fournir des principes et des lignes directives pour l’élaboration de documents d’application étendue relatifs à des systèmes de calfeutrements de joints linéaires soumis à l’essai conformément à l’EN 1366-4. Le domaine d’application étendue est complémentaire au domaine d’application directe décrit dans l’EN 1366-4 et peut s’appliquer à un seul ou plusieurs essais ou être fondé sur ces derniers, lesquels fournissent les informations pertinentes permettant de formuler une application étendue.
Il convient de noter que la présente norme fournit des lignes directives générales sur les effets probables d’une modification. Elle ne donne aucun conseil ni quant à l’ampleur de cette modification, ni quant à la manière de l’évaluer.
Pour déterminer les règles d’application étendue afférentes aux calfeutrements métalliques mécaniques, il convient de noter qu’à l’heure actuelle les preuves en matière d’essais et d’expérience sont jugées insuffisantes. Toutes les conceptions et configurations doivent donc faire l’objet d’un programme d’essai approprié.

Razširjena uporaba rezultatov preskusov požarne odpornosti - 15. del: Tesnilna sredstva za ravne stike

General Information

• Status: Not Published
• ICS: 13.220.50 - Fire-resistance of building materials and elements
• Technical Committee: CEN/TC 127 - Fire safety in buildings
• Drafting Committee: CEN/TC 127/WG 2 - Services
• Current Stage: 4098 - Decision to abandon - Enquiry
• Start Date: 15-Sep-2010
• Completion Date: 15-Sep-2010
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/117 - Horizontal complement to the mandates to CEN/CENELEC concerning the execution of standardization work for the valuation of construction products and elements in respect of their resistance to fire
• Ref Project: oSIST prEN 15080-15:2008 - Extended application of results from fire resistance tests - Part 15: Linear joint seals

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15080-15:2008
01-april-2008
Širša uporaba rezultatov preskusov požarne odpornosti - 15. del: Tesnilna
sredstva za ravne stike
Extended application of results from fire resistance tests - Part 15: Linear joint seals
Erweiterter Anwendungsbereich der Ergebnisse aus Feuerwiderstandsprüfungen - Teil
15: Abdichtungssysteme für Bauteilfugen
Application étendue des résultats des essais de résistance au feu - Partie 15:
Calfeutrements de joints linéaires
Ta slovenski standard je istoveten z: prEN 15080-15
ICS:
13.220.50
oSIST prEN 15080-15:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 15080-15
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2007
ICS

English Version
Extended application of results from fire resistance tests - Part
15: Linear joint seals
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 127.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15080-15:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 15080-15:2007 (E)
Contents Page
Foreword. 3
1 Scope. 4
2 Normative references.4
3 Definitions. 4
4 Extended application principles.8
4.1 General. 8
4.2 Principles common to all generic seal types . 9
5 Extended application report . 10
5.1 Contents of the extended application report . 10
5.2 Review of the extended application report . 11
Annex A (normative) Extended application principles for generic joint seal types. 12


2

---------------------- Page: 3 ----------------------
prEN 15080-15:2007 (E)
Foreword
This document (prEN 15080-15:2007) has been prepared by Technical Committee CEN/TC 127 “Fire
safety in buildings”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of 89/106/EEC.
EN 15080 "Extended application of results from fire resistance tests — Part 15: Linear joint seals"
consists of the following Parts:
 Part ?: Non-loadbearing walls
 Part ?: Non-loadbearing sandwich panels – ceilings
 Part 8: Beams (in course of preparation)
 Part 10: F R ducts
 Part 11: Dampers
 Part 12: Loadbearing masonry walls
 Part 13: Load bearing Columns
 Part 14: Penetration seals (in course of preparation)
 Part 15: Linear Joint Seals
3

---------------------- Page: 4 ----------------------
prEN 15080-15:2007 (E)
1 Scope
The purpose of this document is to provide the principles and guidance for the preparation of
extended application documents for linear joint sealing systems tested in accordance with EN 1366-4.
The field of the extended application document is additional to the direct field of application given
within EN 1366-4 and may be applied to or based on a single test, or a number of tests, which provide
the relevant information for the formulation of an extended application.
It should be noted that this standard provides general guidance on the likely effects of a change. It
gives no guidance as to the magnitude, nor how this magnitude is evaluated.
It should be noted that at present there is considered to be insufficient test evidence and experience
to determine extended application rules for mechanical metal seals. All designs and configurations
must, therefore, be the subject of a suitable test program.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text, and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
EN 1363-1, Fire resistance tests — Part 1: General requirements
EN 1363-2, Fire resistance tests — Part 2: Alternative and additional procedures
EN 1366-3, Fire resistance tests for service installations — Part 3: Penetration seals
EN 1366-4, Fire resistance tests for service installations — Part 4: Linear joint seals
EN 13501-1, Fire classification of construction products and building elements —
Part 1: Classification using test data from reaction to fire tests
EN 13501-2, Fire classification of construction products and building elements —
Part 2: Classification using data from fire resistance tests, (excluding products for use in ventilation
systems)
EN ISO 13943, Fire safety — Vocabulary
3 Definitions
For the purposes of this document the definitions given in EN 1363-1, EN 1363-2, EN 1366-3,
EN 1366-4, EN 13501-1, EN 13501-2 and EN ISO 13943, together with the following, apply:
3.1
fabric seal
a seal comprising a woven fabric, usually glass cloth or similar, which may be used in a combination
with other material, such as metal facings etc. to provide a composite seal

4

---------------------- Page: 5 ----------------------
prEN 15080-15:2007 (E)
3.2
foam seal
a seal made from a one, two or three component expanding foam (expands during application),
applied in-situ
3.3
joint depth
the overall distance between the exposed and unexposed faces across the thickness of the
separating element – see Figure 1
3.4
joint face framing
additional substrate incorporated between the supporting construction and the joint seal
3.5
joint width
the distance between the two adjacent faces of the building element(s) – see Figure 1
3.6
mineral wool based seal
a seal comprised in the majority, or entirety of glass, stone or ceramic wool, which do not rely on a
mastic component for their primary fire resistance performance
3.7
mortar based seal
a seal comprising a cementitious or gypsum based compound, together with other filler materials,
usually mixed on site with water to achieve the required workability
3.8
movement joint
a joint between adjacent building elements or within a building element designed to accommodate a
degree of movement of greater than ± 7.5 % (such as deflection, thermal movement or seismic)
3.9
non-movement joint
a joint between adjacent building elements or within a building element not designed to accommodate
movement greater than ± 7.5 % (such as those designed to accommodate construction tolerances or
irregularities of fit)
3.10
seal depth
the shortest distance between the exposed and unexposed surfaces of the seal – see Figure 1
3.11
seal width
the width of the seal in the non-installed condition (e.g. uncompressed solid seals, see Figure 1A) or
the width of the installed seal where it is equal to or different from the joint width (e.g. overlap) – see
Figure 1B and C
3.12
sealant/mastic/putty based seal
a seal comprising a sealant/mastic/putty material, generally in conjunction with a backing material,
inserted into the joint

5

---------------------- Page: 6 ----------------------
prEN 15080-15:2007 (E)
3.13
strip based seal
a preformed seal normally inserted into the joint and held in place by friction or by means of an
adhesive. These may also include impregnated or multi component (composite, laminated) seals such
as a combination of foam tape with strips of intumescent material
3.14
surface mounted strip
a surface mounted seal applied over the joint to completely cover
...