M/088 - CPD: Reaction to fire

This document specifies a test method for determining the non-combustibility performance, under
specified conditions, of homogeneous products and substantial components of non-homogeneous
products.
Information on the precision of the test method is given in Annex A.

EN-ISO 11925-2 specifies a method of test for determining the ignitability ofproducts by direct small flame impingement under zero impressed irradiance usingvertically oriented test specimens. Information on the precision of the testmethod is given in Annex A (informative).Information on testing not essentiallyflat end-use products is given in Annex B (normative).Information on testingperforated end-use products is given in Annex C (normative).

This document specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens.
Information on the precision of the test method is given in Annex A (informative).
Information on testing not essentially flat end-use products is given in Annex B (normative).
Information on testing perforated end-use products is given in Annex C (normative).

This document specifies a method for the determination of the gross heat of combustion (QPCS) of
products at constant volume in a bomb calorimeter.
This method is intended to be applied to solid products.
NOTE Liquids can be tested with similar equipment and using conditions described in ASTM D240[1], as
described in IEC 61039[2] using ISO 1928[3] test equipment.
Annex A specifies the calculation of the net heat of combustion, QPCI, when required.
Information on the precision of the test method is given in Annex B.

This document specifies a method for the determination of the gross heat of combustion (QPCS) of products at constant volume in a bomb calorimeter.
This method is intended to be applied to solid products.
NOTE Liquids can be tested with similar equipment and using conditions described in ASTM D240[1], as described in IEC 61039[2] using ISO 1928[3] test equipment.
Annex A specifies the calculation of the net heat of combustion, QPCI, when required.
Information on the precision of the test method is given in Annex B.

This standard specifies a test method to determine the ability of a building product to smoulder continuously when exposed to an open flame under the influence of natural convective airflow.
It is intended for all building products classified according to EN 13501-1. Details as to how the products shall be mounted and fixed for this test are given in the relevant product standard. The field of application of the test results shall be defined in the product standard.

This European Standard specifies a test method to determine the propensity (ability) of a building product to smoulder continuously when exposed to an open flame under the influence of natural convective airflow.
It is intended for all building products classified according to EN 13501 1. Details as to how the products is mounted and fixed for this test are given in the relevant product standards. The field of application of the test results is defined in the product standards.

This part of ISO 9239 specifies a method for assessing the wind-opposed burning behaviour and spread of flame of horizontally mounted floorings exposed to a heat flux radiant gradient in a test chamber, when ignited with pilot flames. Annex A gives details of assessing the smoke development, when required. This method is applicable to all types of flooring, e.g. textile carpet, cork, wood, rubber and plastics coverings as well as coatings. Results obtained by this method reflect the performance of the flooring, including any substrate if used. Modifications of the backing, bonding to a substrate, underlay or other changes of the flooring may affect test results. This part of ISO 9239 is applicable to the measurement and description of the properties of floorings in response to heat and flame under controlled laboratory conditions. It should not be used alone to describe or appraise the fire hazard or fire risk of floorings under actual fire conditions. Information on the precision of the test method is given in Annex B.

ISO 9239-1:2010 specifies a method for assessing the wind-opposed burning behaviour and spread of flame of horizontally mounted floorings exposed to a heat flux radiant gradient in a test chamber, when ignited with pilot flames.
This method is applicable to all types of flooring. e.g. textile carpet, cork, wood, rubber and plastics coverings as well as coatings. Results obtained by this method reflect the performance of the flooring, including any substrate if used. Modifications of the backing, bonding to a substrate, underlay or other changes of the flooring may affect test results.
ISO 9239-1:2010 is applicable to the measurement and description of the properties of floorings in response to heat and flame under controlled laboratory conditions. It should not be used alone to describe or appraise the fire hazard or fire risk of floorings under actual fire conditions.

This document specifies a test method for determining the non-combustibility performance, under specified conditions, of homogeneous products and substantial components of non-homogeneous products.
Information on the precision of the test method is given in Annex A.

This International Standard specifies a method of test for determining the non-combustibility performance, under specified conditions, of homogeneous products and substantial components of non-homogeneous products. Information on the precision of the test method is given in annex A.

Ta del ISO 11925 določa metodo preskusa za določanje sposobnosti vžiga proizvodov pri neposrednem stiku z majhnim plamenom in pri ničnih sledeh žarenja z uporabo navpično obrnjenih vzorcev. Informacije o natančnosti preskusne metode so podane v dodatku A.

This part of ISO 11925 specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens. Information on the precision of the test method is given in Annex A.

Ta del ISO 11925 določa metodo preskusa za določanje sposobnosti vžiga proizvodov pri neposrednem stiku z majhnim plamenom in pri ničnih sledeh žarenja z uporabo navpično obrnjenih vzorcev. Informacije o natančnosti preskusne metode so podane v dodatku A.

ISO 11925-2:2010 specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens.

This International Standard specifies a method for the determination of the gross heat of combustion (QPCS) of products at constant volume in a bomb calorimeter. Annex A describes the calculation of the net heat of combustion (QPCI) when required. Information on the precision of the test method is given in Annex B.

ISO 1716:2010 specifies a method for the determination of the gross heat of combustion of products at constant volume in a bomb calorimeter.

This European Standard specifies a method of test for determining the ignitability of building products by direct small flame impingement under zero impressed irradiance using specimens tested in a vertical orientation.  
The products that melt and shrink away from the flame without being ignited may be addressed by the additional procedure given in annex A.
Information on the precision of the test method is given in annex B.

This European Standard specifies a method for assessing the wind-opposed burning behaviour and spread of flame of horizontally mounted floorings exposed to a heat flux radiant gradient in a test chamber, when ignited with  pilot flames. Annex A gives details of assessing the smoke development, when required.
This method is applicable to all types of flooring e.g. textile carpet, cork, wood, rubber and plastics coverings as well as coatings. Results obtained by this method reflect the performance of the flooring, including any substrate if used. Modifications of the backing, bonding to a substrate, underlay or other changes of the flooring may affect test results.
This European Standard is applicable to the measurement and description of the properties of floorings  in response to heat and flame under controlled laboratory conditions. It should not be used alone to describe or appraise the fire hazard or fire risk of floorings  under actual fire conditions.
Information on the precision of the test method is given in annex B.

This European Standard specifies a method of test for determining the non-combustibility performance, under specified conditions, of homogeneous building products and substantial components of non-homogeneous building products.
Information on the precision of the test method is given in annex A.

This European Standard specifies a method of test for determining the ignitability of building products by direct small flame impingement under zero impressed irradiance using specimens tested in a vertical orientation.  
The products that melt and shrink away from the flame without being ignited may be addressed by the additional procedure given in annex A.
Information on the precision of the test method is given in annex B.

This European Standard specifies a method for the determination of the heat of combustion of building products at constant volume in a bomb calorimeter.
This European Standard describes a test method for the measurement of the gross heat of combustion (PCS). Annex A describes the calculation of the net heat of combustion (PCI) when required.
Information on the precision of the test method is given in Annex B.

This European Standard specifies a method for the determination of the heat of combustion of building products at constant volume in a bomb calorimeter.
This European Standard describes a test method for the measurement of the gross heat of combustion (PCS). Annex A describes the calculation of the net heat of combustion (PCI) when required.
Information on the precision of the test method is given in Annex B.

This European Standard specifies a method for assessing the wind-opposed burning behaviour and spread of flame of horizontally mounted floorings exposed to a heat flux radiant gradient in a test chamber, when ignited with  pilot flames. Annex A gives details of assessing the smoke development, when required.
This method is applicable to all types of flooring e.g. textile carpet, cork, wood, rubber and plastics coverings as well as coatings. Results obtained by this method reflect the performance of the flooring, including any substrate if used. Modifications of the backing, bonding to a substrate, underlay or other changes of the flooring may affect test results.
This European Standard is applicable to the measurement and description of the properties of floorings  in response to heat and flame under controlled laboratory conditions. It should not be used alone to describe or appraise the fire hazard or fire risk of floorings  under actual fire conditions.
Information on the precision of the test method is given in annex B.

ISO 1182:2010 specifies a method of test for determining the non-combustibility performance, under specified conditions, of homogeneous products and substantial components of non-homogeneous products.

This European Standard specifies a method of test for determining the non-combustibility performance, under specified conditions, of homogeneous building products and substantial components of non-homogeneous building products.
Information on the precision of the test method is given in annex A.

This European Standard specifies the conditioning procedures for samples of building products, and the rules for the selection of substrates for floor coverings and wall/ceiling surface products, when carrying out reaction to fire tests. This European Standard does not cover pre-drying procedures for prEN 1182:1998 or the washing and cleaning procedures relating to durability aspects, which are covered  by product standards.

This European Standard specifies the conditioning procedures for samples of building products, and the rules for the selection of substrates for floor coverings and wall/ceiling surface products, when carrying out reaction to fire tests. This European Standard does not cover pre-drying procedures for prEN 1182:1998 or the washing and cleaning procedures relating to durability aspects, which are covered  by product standards.

This standard specifies the procedure for classification of construction products and element families using data from fire resistance tests which are within the field of application of the relevant test method. Classification on the basis of extended application is not within the scope of this Standard.

This standard specifies the procedure for classification of construction products and element families using data from fire resistance tests which are within the field of application of the relevant test method. Classification on the basis of extended application is not within the scope of this Standard.

This European Standard provides the reaction to fire classification procedure for all construction products, including products incorporated within building elements.
Products are considered in relation to their end use application.
This document applies to two categories, which are treated separately in this European Standard:
construction products, excluding floorings;
floorings.
NOTE   The treatment of some families of products is still under review and can necessitate amendments to this standard (see European Decision 2000/147/EC).

This European Standard provides the reaction to fire classification procedure for all construction products, including products incorporated within building elements.
Products are considered in relation to their end use application.
This document applies to two categories, which are treated separately in this European Standard:
construction products, excluding floorings;
floorings.
NOTE   The treatment of some families of products is still under review and can necessitate amendments to this standard (see European Decision 2000/147/EC).