EN 12588:2006
(Main)Lead and lead alloys - Rolled lead sheet for building purposes
Lead and lead alloys - Rolled lead sheet for building purposes
This European Standard specifies the designation, the requirements for chemical composition, surface condition and dimensional tolerances for rolled lead sheet. Lead sheet covered by this European standard is made by the roll deformation process and is intended for roofs, flashings, weatherings, claddings, pre-formed panels, damp-proof courses and similar building work.
No requirements for supporting construction, design of roof or cladding systems and methods of joining are included.
Blei und Bleilegierungen - Gewalzte Bleche aus Blei für das Bauwesen
Diese Europäische Norm legt die Bezeichnung sowie Anforderungen an die chemische Zusammensetzung, Oberflächenbeschaffenheit und Maßtoleranzen für gewalzte Bleche aus Blei fest. Bleche aus Blei nach dieser Europäischen Norm werden im Formwalzverfahren hergestellt und sind für Dächer, Verwahrungen, Ab¬deckungen, Fassadenbekleidungen, vorgefertigte Fassadenelemente, wasserdichte Sperrschichten und ähnliche bautechnische Zwecke bestimmt.
Diese Norm enthält keine Anforderungen an Tragkonstruktionen, Dachkonstruktionen, Verkleidungsverfahren sowie Verbindungsmethoden.
Plomb et alliages de plomb - Feuilles de plomb laminé pour le bâtiment
La présente Norme européenne spécifie la désignation, les exigences en matière de composition chimique,
l'aspect de surface et les tolérances dimensionnelles des feuilles de plomb laminé. Les feuilles de plomb
traitées par la présente Norme européenne sont fabriquées par laminage et sont destinées aux toitures,
accessoires d'étanchéité et de couverture, bardages, panneaux préformés, couches isolantes et travaux de
construction similaires.
Les exigences concernant le support de la construction, la conception du toit ou des systèmes de bardage et
les méthodes de raccordement ne sont pas incluses.
Svinec in svinčeve zlitine - Valjana svinčena pločevina za gradbeništvo
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lead and lead alloys - Rolled lead sheet for building purposesQLãWYRPlomb et alliages de plomb - Feuilles de plomb laminé pour le bâtimentBlei und Bleilegierungen - Gewalzte Bleche aus Blei für das BauwesenTa slovenski standard je istoveten z:EN 12588:2006SIST EN 12588:2007en77.150.60L]GHONLLead, zinc and tin productsICS:SIST EN 12588:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 12588:200701-februar-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12588December 2006ICS 77.150.60Supersedes EN 12588:1999
English VersionLead and lead alloys - Rolled lead sheet for building purposesPlomb et alliages de plomb - Feuilles de plomb laminé pourle bâtimentBlei und Bleilegierungen - Gewalzte Bleche aus Blei für dasBauwesenThis European Standard was approved by CEN on 19 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12588:2006: E
European numbering system for lead and lead alloys.11 A.1 Introduction.11 A.2 General.11 A.3 Details of the system.11 A.3.1 General.11 A.3.2 Structure of number.11 A.4 Allocation and administration of material numbers.12
Environment: Studies into construction and demolition waste carried out by Enviros Aspinall have shown that the recycling rate of the product is above 90 %. Recommendations have been included within this standard on good management of surplus material during construction. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
In this European Standard, the performance of the product has been defined as far as possible in terms of a number of type tests. The performance of a building element made with these products depends not only on the properties of the product as it is required by this European standard, but also on the design and quality of the fabrication of the building element and on the design, construction and behaviour of the part of the building concerned in relation to the environment and conditions of use. The lead sheet supplied shall be specified and used according to the National Code of Practice, depending on service conditions such as exposure to direct sunlight and the area of the piece of lead to be fixed.
No requirements for supporting construction, design of roof or cladding systems and methods of joining are included. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 11014-1, Safety data sheet for chemical products – Part 1: Content and order of sections 3 Terms and definitions For the purposes of this European Standard, the following term and definition applies.
rolled lead sheet flat product made of lead of rectangular cross-section with uniform thickness and width supplied in coiled or flat form 4 Designation 4.1 Material number The material is designated with a number (see 6.1). This material number designation is in accordance with the system given in Annex A (normative). 4.2 Product The product designation for products to this European standard shall consist of: denomination (Lead sheet); number of this European Standard (EN 12588); nominal thickness in millimetres. NOTE The material number is not a part of the product designation because this European standard contains only one material. The derivation of a product designation is shown in the following example.
Lead sheet EN 12588 -1,25 Denomination
Number of this European Standard
Nominal thickness in millimetres
5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and/or order the following information: a) quantity of product to be delivered (number of pieces); b) product designation (according to 4.2); c) nominal width in millimetres; d) nominal length in metres; e) form of delivery (coiled or flat). In addition, the purchaser shall also state on the enquiry and/or order if any of the following is required: f) declaration of conformity (see clause 8); g) special packaging; h) any other requirements. EXAMPLE Ordering details for 10 pieces lead sheet in accordance with EN 12588, nominal thickness 2,50 mm, nominal width 1 000 mm, nominal length 2,0 m, delivered in coils, with a declaration of conformity: 10 pieces Lead sheet EN 12588 - 2,50
- nominal width 1 000 mm
- nominal length 2,0 m
- coils
- declaration of conformity
6.2 Dimensions and tolerances 6.2.1 Dimensions The length, width and thickness shall be agreed between the purchaser and the supplier, within the following limits:
thickness: up to and including 6 mm;
width: from 100 mm up to and including 2 500 mm; length: up to and including 12 m in the coiled form. 6.2.2 Tolerances 6.2.2.1 Thickness The maximum deviation from the ordered nominal thickness, when measured in accordance with 7.1.2, shall not exceed ± 5 %. 6.2.2.2 Width The maximum deviation from the ordered nominal width shall not exceed ± 5 mm. 6.2.2.3 Length The maximum deviation from the ordered nominal length shall not exceed
mm. +50
Three evenly spaced measurements shall be carried out across the sheet and five along the sheet at 100 mm in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.