iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 11363-1:2010/AC:2012

(Corrigendum)

Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 2 (ISO 11363-1:2010/Cor 2:2012)

Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 2 (ISO 11363-1:2010/Cor 2:2012)

This part of ISO 11363 specifies dimensions and tolerances for taper screw threads of nominal diameter 17,4 mm (designated 17E) and 25,8 mm (designated 25E) used for the connection of valves to gas cylinders. It does not cover the connection requirements for: - mechanical strength; - gas tightness; - capability of repeated assembly and dismounting operations. Gauge inspection is covered by ISO 11363-2.

Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit Gasflaschen - Teil 1: Spezifikationen - Berichtigung 2 (ISO 11363-1:2010/Cor 2:2012)

Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur les bouteilles à gaz - Partie 1: Spécifications - Rectificatif technique 2 (ISO 11363-1:2010/Cor 2:2012)

Plinske jeklenke - Konična navoja 17E in 25E za priključitev ventila na plinsko jeklenko - 1. del: Specifikacije - Tehnični popravek 2 (ISO 11363-1:2010/Cor 2:2012)

Ta del ISO 11363 določa dimenzije in tolerance za konična navoja vijakov z nominalnim premerom 17,4 mm (oznaka 17E) in 25,8 mm (oznaka 25E), ki se uporabljata za priključitev ventila na plinsko jeklenko. Ne zajema zahtev za priključitev za:
– mehansko trdnost;
- nepropustnost za pline;
- sposobnost večkratnih operacij sestavljanja in razstavljanja.
Pregled merilnika je zajet v ISO 11363-2.

General Information

Status
Withdrawn
Publication Date
14-Jan-2012
Withdrawal Date
20-Feb-2018
ICS
23.020.30 - Pressure vessels, gas cylinders
23.020.35 - Gas cylinders
Technical Committee
CEN/TC 23 - Transportable gas cylinders
Drafting Committee
CEN/TC 23 - Transportable gas cylinders
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
21-Feb-2018
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Ref Project
SIST EN ISO 11363-1:2010/AC:2012 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 2 (ISO 11363-1:2010/Cor 2:2012)

Relations

Replaces
EN ISO 11363-1:2010/AC:2011 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 1 (ISO 11363-1:2010/Cor 1:2011)
Effective Date
19-Nov-2011
Replaced By
EN ISO 11363-1:2018 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2018)
Effective Date
08-Jun-2022
Corrects
EN ISO 11363-1:2010 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2010)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 11363-1:2010/AC:2012EN ISO 11363-1:2010/AC:2012
PreviousNext
Corrigendum
EN ISO 11363-1:2010/AC:2012
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit Gasflaschen - Teil 1: Spezifikationen (ISO 11363-1:2010/Cor 2:2012)Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur les bouteilles à gaz - Partie 1: Spécifications - Rectificatif technique 2 (ISO 11363-1:2010/Cor 2:2012)Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 2 (ISO 11363-1:2010/Cor 2:2012)23.020.30MHNOHQNHPressure vessels, gas cylinders21.040.30Posebni navojiSpecial screw threadsICS:Ta slovenski standard je istoveten z:EN ISO 11363-1:2010/AC:2012SIST EN ISO 11363-1:2010/AC:2012en,fr,de01-maj-2012SIST EN ISO 11363-1:2010/AC:2012SLOVENSKI
STANDARDSIST EN ISO 11363-1:2010/AC:20111DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 11363-1:2010/AC
January 2012
Janvier 2012
Januar 2012 ICS 23.020.30 Supersedes EN ISO 11363-1:2010/AC:2011English version Version Française Deutsche Fassung
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 2 (ISO 11363-1:2010/Cor 2:2012)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur les bouteilles à gaz - Partie 1: Spécifications - Rectificatif technique 2 (ISO 11363-1:2010/Cor 2:2012)
Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit Gasflaschen - Teil 1: Spezifikationen (ISO 11363-1:2010/Cor 2:2012) This corrigendum becomes effective on 15 January 2012 for incorporation in the three official language versions of the EN.
Ce corrigendum prendra effet le 15 janvier 2012 pour incorporation dans les trois versions linguistiques officielles de la EN.
Die Berichtigung tritt am 15. Januar 2012 zur Einarbeitung in die drei offiziellen Sprachfassungen der EN in Kraft.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Bruss
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 9809-3:2019(Main)
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 3: Normalized steel cylinders and tubes (ISO 9809-3:2019)
SIST EN ISO 9809-3:2019

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at the time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l.
It is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for normalized or normalized and tempered steel cylinders and tubes.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9809-1:2019(Main)
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 1: Quenched and tempered steel cylinders and tubes with tensile strength less than 1 100 MPa (ISO 9809-1:2019)
SIST EN ISO 9809-1:2019

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l.
It is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for quenched and tempered steel cylinders and tubes with a maximum actual tensile strength Rma of less than 1 100 MPa.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9809-2:2019(Main)
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 2: Quenched and tempered steel cylinders and tubes with tensile strength greater than or equal to 1 100 MPa (ISO 9809-2:2019)
SIST EN ISO 9809-2:2019

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l.
it is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for quenched and tempered steel cylinders and tubes with an actual tensile strength Rma ≥ 1 100 MPa.
It is not applicable to cylinders and tubes with Rma, max > 1 300 MPa for diameters >140 mm and guaranteed wall thicknesses a′ ≥ 12 mm and for cylinders and tubes with Rma, max > 1 400 MPa for diameters ≤140 mm and guaranteed wall thicknesses a′ ≥ 6 mm because, beyond these limits, additional requirements can apply.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18119:2018(Main)
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes - Periodic inspection and testing (ISO 18119:2018)
SIST EN ISO 18119:2019

This document specifies the requirements for periodic inspection and testing to verify the integrity of cylinders and tubes to be re-introduced into service for a further period of time.
This document is applicable to seamless steel and seamless aluminium-alloy transportable gas cylinders (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l and to seamless steel and seamless aluminium-alloy transportable gas tubes (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity greater than 150 l. It also applies, as far as practical, to cylinders of less than 0,5 l water capacity.
This document does not apply to the periodic inspection and maintenance of acetylene cylinders or to the periodic inspection and testing of composite cylinders.
NOTE       Unless noted by exception, the use of the word "cylinder" in this document refers to both cylinders and tubes.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    65 pages
    German language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    65 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13769:2018(Main)
Gas cylinders - Stamp marking (ISO 13769:2018)
SIST EN ISO 13769:2018

This document specifies stamp marking of transportable gas cylinders of volumes greater than 0,12 l and up to or equal to 150 l and tubes of volumes up to or equal to 3 000 l, including:
-      steel and aluminium-alloy gas cylinders;
-      composite gas cylinders;
-      acetylene cylinders;
-      liquefied petroleum gas (LPG) cylinders (see Annex A); and
-      small cylinders (see Annex B).
Unless noted by exception, the use of "cylinder" in this document refers to the above types of cylinders.
Non-refillable cylinders are addressed by this standard.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11363-1:2018(Main)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2018)
SIST EN ISO 11363-1:2018

ISO 11363-1:2018 specifies dimensions and tolerances for taper screw threads of nominal diameter 17,4 mm (designated as 17E) and 25,8 mm (designated as 25E) used for the connection of valves to gas cylinders.
ISO 11363-1:2018 does not cover the connection requirements for
-      mechanical strength,
-      gas tightness, and
-      capability of repeated assembly and dismounting operations.
Gauge inspection is covered by ISO 11363‑2.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11363-2:2017(Main)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-2:2017)
SIST EN ISO 11363-2:2018

ISO 11363-2:2017 specifies types, dimensions and principles of use of gauges, to be used in conjunction with the taper threads specified in ISO 11363-1 (i.e. 17E and 25E threads).
It provides examples of calculations for thread gauge dimensions on the large end diameter (Annex A) and draws attention to the limitations of the gauging system specified (Annex B).

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15996:2017(Main)
Gas cylinders - Residual pressure valves - Specification and type testing of cylinder valves incorporating residual pressure devices (ISO 15996:2017)
SIST EN ISO 15996:2018

ISO 15996:2017 specifies design, type testing and marking requirements for cylinder valves incorporating residual pressure devices, hereinafter referred to as residual pressure valves (RPVs). This document applies to the following types of RPVs:
a)    cylinder valves intended to be fitted to refillable transportable gas cylinders;
b)    main valves (excluding ball valves) for cylinder bundles;
c)    cylinder valves or main valves with integrated pressure regulator (VIPR);
d)    valves for pressure drums and tubes;
which convey compressed or liquefied gases.
NOTE          Where there is no risk of ambiguity, cylinders, pressure drums, tubes and cylinder bundles are addressed with the collective term "cylinder" within this document.
These requirements are in addition to those in ISO 10297.
For RPD stand-alone devices this document can also be applied.
ISO 15996:2017 does not apply to RPVs for portable fire extinguishers, cryogenic equipment, low pressure refrigerant gases (cylinder test pressure less than 50 bar), dissolved gases or liquefied petroleum gas (LPG).

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10156:2017(Main)
Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2017)
SIST EN ISO 10156:2018

ISO 10156:2017 specifies methods for determining whether or not a gas or gas mixture is flammable in air and whether a gas or gas mixture is more or less oxidizing than air under atmospheric conditions.
ISO 10156:2017 is intended to be used for the classification of gases and gas mixtures including the selection of gas cylinder valve outlets.
ISO 10156:2017 does not cover the safe preparation of these mixtures under pressure and at temperatures other than ambient.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17879:2017(Main)
Gas cylinders - Self-closing cylinder valves - Specification and type testing (ISO 17879:2017)
SIST EN ISO 17879:2018

ISO 17879:2017 specifies the design, type testing, marking and manufacturing tests and examinations requirements for self-closing cylinder valves intended to be fitted to refillable transportable gas cylinders which convey compressed, liquefied or dissolved gases.
NOTE 1       The main applications for such self-closing cylinder valves are in the calibration gas and beverage industries.
ISO 17879:2017 covers the function of a self-closing cylinder valve as a closure.
NOTE 2       Requirements for standard cylinder valves are given in ISO 10297. Requirements for quick-release cylinder valves are given in ISO 17871.
ISO 17879:2017 is not applicable to self-closing cylinder valves for cryogenic equipment, for portable fire extinguishers, or for liquefied petroleum gas (LPG).
NOTE 3       Requirements for valves for cryogenic vessels are specified in ISO 21011 and at a regional level, for example, in EN 1626. Requirements for valves for portable fire extinguishers at a regional level are specified, for example, in EN 3 series. Requirements for self-closing LPG cylinder valves are specified in ISO 14245.
NOTE 4       Additional requirements for pressure-relief devices might be specified in international/regional regulations/standards.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day