EN ISO 5270:2012
(Main)Pulps - Laboratory sheets - Determination of physical properties (ISO 5270:2012)
Pulps - Laboratory sheets - Determination of physical properties (ISO 5270:2012)
ISO 5270:2012 specifies the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps. It is applicable to laboratory sheets prepared in accordance with ISO 5269-1, ISO 5269-2 or ISO 5269-3.
In ISO 5270:2012, it is left to the pulp producer and the pulp user to agree upon which properties are relevant to be tested. The results are, if applicable, reported in index form.
Faserstoff - Laborblätter- Bestimmung der physikalischen Eigenschaften (ISO 5270:2012)
Diese Internationale Norm legt die relevanten internationalen Normen fest, die für die Bestimmung der
physikalischen Eigenschaften von aus Zellstoff hergestellten Laborblättern benutzt werden. Sie ist für
Laborblätter anwendbar, die nach ISO 5269-1, ISO 5269-2 oder ISO 5269-3 vorbereitet wurden.
Die nach dieser Internationalen Norm zu prüfenden relevanten Eigenschaften sind zwischen Hersteller und
Zellstoff-Abnehmer zu vereinbaren, siehe die Liste der Verweisungen nach ISO 536 in Abschnitt 2.
Vorhandene Ergebnisse werden in Tabellenform angegeben.
Pâtes - Feuilles de laboratoire - Détermination des propriétés physiques (ISO 5270:2012)
L'ISO 5270:2012 spécifie les Normes internationales à utiliser pour la détermination des propriétés physiques des feuilles de laboratoire fabriquées à partir de pâtes de tous types. Elle est applicable à des feuilles de laboratoire préparées conformément à l'ISO 5269‑1, l'ISO 5269‑2 ou l'ISO 5269‑3.
Dans l'ISO 5270:2012, il est laissé à l'initiative du fabricant de pâte et de l'utilisateur de la pâte de convenir des propriétés pertinentes à soumettre à essai. Les résultats sont consignés, s'il y a lieu, sous forme d'indice.
Vlaknine - Laboratorijski listi - Ugotavljanje fizikalnih lastnosti (ISO 5270:2012)
Ta mednarodni standard določa ustrezne mednarodne standarde, ki se uporabljajo za določanje fizikalnih lastnosti laboratorijskih listov iz vseh vrst vlaknin. Velja za laboratorijske liste, pripravljene v skladu s standardi ISO 5269-1, ISO 5269-2 ali ISO 5269-3. V tem mednarodnem standardu se izdelovalec vlaknin in njihov uporabnik dogovorita, katere lastnosti so pomembne za preskus. Rezultati, če je to primerno, so zapisani v indeksni obliki.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2012
1DGRPHãþD
SIST EN ISO 5270:2000
SIST ISO 5270:2000
Vlaknine - Laboratorijski listi - Ugotavljanje fizikalnih lastnosti (ISO 5270:2012)
Pulps - Laboratory sheets - Determination of physical properties (ISO 5270:2012)
Faserstoff- Laborblätter- Bestimmung der physikalischen Eigenschaften (ISO 5270:2012)
Pâtes - Feuilles de laboratoire - Détermination des propriétés physiques (ISO
5270:2012)
Ta slovenski standard je istoveten z: EN ISO 5270:2012
ICS:
85.040 Vlaknine Pulps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 5270
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2012
ICS 85.040 Supersedes EN ISO 5270:1999
English Version
Pulps - Laboratory sheets - Determination of physical properties
(ISO 5270:2012)
Pâtes - Feuilles de laboratoire - Détermination des Faserstoff - Laborblätter- Bestimmung der physikalischen
propriétés physiques (ISO 5270:2012) Eigenschaften (ISO 5270:2012)
This European Standard was approved by CEN on 30 September 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5270:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 5270:2012) has been prepared by Technical Committee ISO/TC 6 “Paper, board and
pulps” in collaboration with Technical Committee CEN/TC 172 “Pulp, paper and board” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the
latest by April 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 5270:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5270:2012 has been approved by CEN as a EN ISO 5270:2012 without any modification.
INTERNATIONAL ISO
STANDARD 5270
Third edition
2012-10-01
Pulps — Laboratory sheets —
Determination of physical properties
Pâtes — Feuilles de laboratoire — Détermination des propriétés physiques
Reference number
ISO 5270:2012(E)
©
ISO 2012
ISO 5270:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 5270:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Principle . 2
4 Apparatus . 2
5 Trimmed laboratory sheets . 2
5.1 Selection of laboratory sheets . 2
5.2 Conditioning of laboratory sheets . 2
5.3 Optical properties . 3
5.4 Determination of grammage, bulking thickness and apparent bulk density . 3
5.5 Preparation of test pieces . 3
6 Procedures for physical properties (“low grammage” sheets) . 4
6.1 General . 4
6.2 Tensile properties . 5
6.3 Tear index . 5
6.4 Burst index . 5
6.5 Air permeance . 5
6.6 Folding endurance . 5
7 Procedures for physical properties (“high grammage” sheets) . 6
7.1 General . 6
7.2 Bending resistance index . 6
7.3 Flat crush resistance index after laboratory fluting . 6
7.4 Ring crush resistance index . 6
7.5 Short span compression index . 6
7.6 Z-directional tensile strength . 7
8 Test report . 7
Bibliography . 8
ISO 5270:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5270 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps, Subcommittee SC 5, Test
methods and quality specifications for pulps.
This third edition cancels and replaces the second edition (ISO 5270:1998), which has been technically revised.
The list of relevant International Standards for paper and board, to be used for testing the physical properties
of laboratory sheets, has been updated and new standards, such as ISO 1924-3 and ISO 15754, have been
included. The option to determine air permeance, using the Bendtsen method (ISO 5636-3) or the Sheffield
method (ISO 5636-4) has been inserted, as well as the option to measure optical properties.
iv © ISO 2012 – All rights reserved
ISO 5270:2012(E)
Introduction
This International Standard includes the determination of physical properties of both “low grammage” sheets
and “high grammage” sheets, prepared in accordance with ISO 5269-1, ISO 5269-2 or ISO 5269-3. The
oven-dry grammage of the “low grammage” sheets is (60 ± 2) g/m using the conventional sheet former, as
described in ISO 5269-1 and ISO 5269-3, or (75 ± 2) g/m using the Rapid-Köthen sheet former, as described
in ISO 5269-2 and ISO 5269-3. The oven-dry grammage of the “high grammage” sheets is 140 g/m , with a
tolerance of 3 % using the conventional and the Rapid Köthen sheet formers, except for the z-directional tensile
strength where the grammage is ≥ 90 g/m .
For determination of physical properties, ISO 5270 refers to the relevant International Standards for paper
and board for the description and calibration of the required equipment, and for the calculation and reporting
of results. This International Standard, however, specifies the procedures for testing laboratory sheets where
the amount of material is limited, compared to testing of paper and board to which the relevant International
Standards referred to are applicable, and for that reason there may be a discrepancy.
INTERNATIONAL STANDARD ISO 5270:2012(E)
Pulps — Laboratory sheets — Determination of physical
properties
1 Scope
This International Standard specifies the relevant International Standards to be used for the determination of
physical properties of laboratory sheets made of all kind of pulps. It is applicable to laboratory sheets prepared
in accordance with ISO 5269-1, ISO 5269-2 or ISO 5269-3.
In this International Standard, it is left to the pulp producer and the pulp user to agree upon which properties
are relevant to be tested. The results are, if applicable, reported in index form.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 187:1990, Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for
monitoring the atmosphere and conditioning of samples
ISO 534, Paper and board — Determination of thickness, density
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.