iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10113-3:1993

(Main)

Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels

Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels

Part 3 of this European Standard, in addition to part 1, specifies requirements for flat products with nominal thickness ¿ 63 mm and long products with nominal thickness ¿ 150 mm of hot-rolled weldable fine grain structural steel in the thermomechanical rolled condition in the grades and qualities given in table 1 (chemical composition) and tables 3, 4 and 5 (mechanical properties).

Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 3: Lieferbedingungen für thermomechanisch gewalzte Stähle

Der Teil 3 dieser europäischen Norm enthält in Verbindung mit Teil 1 die Anforderungen an Flacherzeugnisse in Nenndicken <= 63 mm und Langerzeugnisse in Nenndicken <= 150 mm aus warmgewalzten schweissgeeigneten Feinkornbaustählen der Sorten und Gütegruppen nach den Tabelle 1 und 2 (chemische Zusammensetzung) sowie nach den Tabellen 3 bis 5 (mechanische Eigenschaften) im thermomechanischen gewalzten Zustand.

Produits laminés à chaud en aciers de construction soudable à grains fins - Partie 3: Conditions de livraison des aciers obtenus par laminage thermomécanique

La présente partie 3 de la norme européenne vient s'ajouter à la partie 1 et spécifie les caractéristiques des produits plats d'épaisseur nominale <= 63 mm et des produits longs d'épaisseur <= 150 mm en aciers de construction soudables à grains fins laminés à chaud livrés à l'état de laminage thermomécanique et dans les nuances et qualités données au tableau 1 (pour la composition chimique), et aux tableaux 3, 4 et 5 (pour les caractéristiques mécaniques).

Vroče valjani izdelki iz varivih drobnozrnatih konstrukcijskih jekel - 3. del: Dobavni pogoji za termomehansko valjana jekla

General Information

Status
Withdrawn
Publication Date
08-Mar-1993
Withdrawal Date
09-Nov-2004
ICS
77.140.10 - Heat-treatable steels
Technical Committee
ECISS/TC 103 - Structural steels other than reinforcements
Drafting Committee
ECISS/TC 10 - Structural steels - Qualities
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
10-Nov-2004
Completion Date
10-Nov-2004
Mandate
M/BC/CEN/86/1 - ECISS - 1st programme
Ref Project
SIST EN 10113-3:1997 - Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels

Relations

Parent
EN 10113-1:1993 - Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions
Effective Date
22-Dec-2008
Replaced By
EN 10025-1:2004 - Hot rolled products of structural steels - Part 1: General technical delivery conditions
Effective Date
22-Dec-2008
Replaced By
EN 10025-4:2004 - Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Effective Date
22-Dec-2008

Buy Standard

EN 10113-3:1997EN 10113-3:1997
PreviousNext
Standard
EN 10113-3:1997
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 3: Lieferbedingungen für thermomechanisch gewalzte StähleProduits laminés a chaud en aciers de construction soudable a grains fins - Partie 3: Conditions de livraison des aciers obtenus par laminage thermomécaniqueHot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels77
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10225-3:2019+A1:2023(Main + Amendment)
Weldable structural steels for fixed offshore structures - Technical delivery conditions - Part 3: Hot finished hollow sections
SIST EN 10225-3:2019+A1:2023

This document specifies requirements for weldable structural steels made of hot finished seamless and high frequency welded hollow sections to be used in the fabrication of fixed offshore structures.
The following thickness limitations are given in this standard:
-   for seamless hollow sections up to and including 65 mm;
-   for HFW hollow sections up to and including 25,4 mm.
Greater thicknesses can be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex E on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 770 MPa are specified together with impact properties at temperatures down to -40 °C.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-4:2019+A1:2022(Main + Amendment)
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
SIST EN 10025-4:2019+A1:2023

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-6:2019+A1:2022(Main + Amendment)
Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
SIST EN 10025-6:2019+A1:2023

This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-3:2019(Main)
Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
SIST EN 10025-3:2019

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 250 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-2:2019(Main)
Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
SIST EN 10025-2:2019

This document specifies the technical delivery conditions for flat and long products as well as semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 1 to 5 (chemical composition) and Tables 6 to 8 (mechanical properties) in the usual delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 2 and 4) (chemical composition) and Table 7 (mechanical properties). This document does not apply to structural hollow sections (see EN 10210 1 and EN 10219 1) and tubes.
The technical delivery conditions apply to:
-   thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460JR, J0, J2, K2 and S500J0;
-   thicknesses ≤ 400 mm for flat products of qualities JR, J0, J2 and K2;
-   thicknesses ≤ 250 mm for flat and long products of all other grades and qualities.
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
This document foresees that semi-finished products which are to be converted to rolled finished products conforming to this document are the subject of special agreements at the time of the order. The chemical compositions are also agreed to at the time of the order; the values are within the limits of Tables 1 and 2.
For certain grades and product forms suitability for particular applications are specified at the time of the order (see 7.4.2, 7.4.3 and Table 9).

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-5:2019(Main)
Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
SIST EN 10025-5:2019

This document specifies technical delivery conditions for flat and long products of hot rolled steels with improved atmospheric corrosion resistance in the grades and qualities given in Tables 2 and 3 (chemical composition) and Tables 4 and 5 (mechanical properties) in the usual delivery conditions as given in 6.3.
The thicknesses in which products of the steel grades and qualities specified in this document can be supplied are given in Table 1.
Table 1 - Product forms for the different steel grades with improved atmospheric corrosion resistance depending on their thickness
[table not reproduced]
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10225-1:2019(Main)
Weldable structural steels for fixed offshore structures - Technical delivery conditions - Part 1: Plates
SIST EN 10225-1:2019

This document specifies requirements for weldable structural steels, in the form of plates, to be used in the fabrication of fixed offshore structures.
The following thickness limitations are given in this standard:
- S355NLO up to and including 200 mm;
- S355MLO, S420MLO, S460MLO, S500MLO up to and including 120 mm;
- S420QLO, S460QLO, S500QLO, S550QLO, S620QLO, S690QLO up to and including 150 mm.
Greater thicknesses can be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector, including plate for structural hollow sections (see EN 10225-4). It does not apply to plates supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex F on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 690 MPa are specified together with impact properties at temperatures down to -40 °C.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10225-2:2019(Main)
Weldable structural steels for fixed offshore structures - Technical delivery conditions - Part 2: Sections
SIST EN 10225-2:2019

This document specifies requirements for weldable structural steels, in the form of sections (e.g. H-, I-, Z-sections, U-channels, angles and tees) excluding hollow sections, to be used in the fabrication of fixed offshore structures. The thickness limitation in this standard is up to and including 63 mm.
For steel qualities with mechanical properties in the transverse direction (named xL1O) sections with flange widths smaller than 180 mm and channels with flange widths smaller than 90 mm cannot be ordered.
Greater thicknesses may be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex C on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 460 MPa are specified together with impact properties at temperatures down to -40 °C.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10225-4:2019(Main)
Weldable structural steels for fixed offshore structures - Technical delivery conditions - Part 4: Cold formed welded hollow sections
SIST EN 10225-4:2019

This document specifies requirements for submerged arc welded (SAW) and high frequency welded (HFW) cold formed hollow sections to be used in the fabrication of fixed offshore structures.
The thickness limit for SAWL circular hollow sections is up to and including 50,8 mm, for HFW circular hollow sections up to and including 25,4 mm and for HFW square and rectangular hollow sections up to and including 12,5 mm.
Greater thicknesses for SAWL hollow sections can be agreed provided the technical requirements of this European Standard are maintained.
NOTE 1   This document has an Annex E for SAWH round hollow sections with a thickness limit of 30,0 mm, and an Annex F for high strength square and rectangular HFW hollow sections made of steel grades S500 to S700.
This European Standard is applicable to steels for offshore structures designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE 2   This document has an informative Annex G on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 700 MPa are specified together with impact properties at temperatures down to -40 °C.
NOTE 3   A range of material grades is specified in this standard and the user can select the grade most appropriate to the intended use and its service condition.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10238:2009(Main)
Automatically blast-cleaned and automatically prefabrication primed structural steel products
SIST EN 10238:2009

This European Standard specifies requirements for automatically blast-cleaned and automatically
prefabrication primed structural steel products.
This European Standard does not cover manual blast cleaning and/or manual spray painting.
NOTE Where the steel is less than 5 mm thick, care should be exercised to ensure it is not deformed by blast
cleaning.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day