iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 10113-3:1997

(Main)

Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels

Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels

Part 3 of this European Standard, in addition to part 1, specifies requirements for flat products with nominal thickness ? 63 mm and long products with nominal thickness ? 150 mm of hot-rolled weldable fine grain structural steel in the thermomechanical rolled condition in the grades and qualities given in table 1 (chemical composition) and tables 3, 4 and 5 (mechanical properties).

Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 3: Lieferbedingungen für thermomechanisch gewalzte Stähle

Der Teil 3 dieser europäischen Norm enthält in Verbindung mit Teil 1 die Anforderungen an Flacherzeugnisse in Nenndicken <= 63 mm und Langerzeugnisse in Nenndicken <= 150 mm aus warmgewalzten schweissgeeigneten Feinkornbaustählen der Sorten und Gütegruppen nach den Tabelle 1 und 2 (chemische Zusammensetzung) sowie nach den Tabellen 3 bis 5 (mechanische Eigenschaften) im thermomechanischen gewalzten Zustand.

Produits laminés a chaud en aciers de construction soudable a grains fins - Partie 3: Conditions de livraison des aciers obtenus par laminage thermomécanique

La présente partie 3 de la norme européenne vient s'ajouter a la partie 1 et spécifie les caractéristiques des produits plats d'épaisseur nominale <= 63 mm et des produits longs d'épaisseur <= 150 mm en aciers de construction soudables a grains fins laminés a chaud livrés a l'état de laminage thermomécanique et dans les nuances et qualités données au tableau 1 (pour la composition chimique), et aux tableaux 3, 4 et 5 (pour les caractéristiques mécaniques).

Vroče valjani izdelki iz varivih drobnozrnatih konstrukcijskih jekel - 3. del: Dobavni pogoji za termomehansko valjana jekla

General Information

Status
Withdrawn
Publication Date
30-Nov-1997
Withdrawal Date
28-Feb-2005
ICS
77.140.10 - Heat-treatable steels
Technical Committee
IFEK - Ferrous metals
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Mar-2005
Due Date
01-Mar-2005
Completion Date
01-Mar-2005
Mandate
M/BC/CEN/86/1 - ECISS - 1st programme
Ref Project
EN 10113-3:1993 - Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels

Relations

Replaced By
SIST EN 10025-1:2004 - Hot rolled products of structural steels - Part 1: General technical delivery conditions
Effective Date
01-Mar-2005
Replaced By
SIST EN 10025-4:2004 - Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Effective Date
01-Mar-2005
Parent
SIST EN 10113-1:1997 - Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions
Effective Date
22-Dec-2008

Buy Standard

EN 10113-3:1997EN 10113-3:1997
PreviousNext
Standard
EN 10113-3:1997
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 3: Lieferbedingungen für thermomechanisch gewalzte StähleProduits laminés a chaud en aciers de construction soudable a grains fins - Partie 3: Conditions de livraison des aciers obtenus par laminage thermomécaniqueHot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels77
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 10225-3:2019+A1:2023(Main + Amendment)
Weldable structural steels for fixed offshore structures - Technical delivery conditions - Part 3: Hot finished hollow sections
EN 10225-3:2019+A1:2023

This document specifies requirements for weldable structural steels made of hot finished seamless and high frequency welded hollow sections to be used in the fabrication of fixed offshore structures.
The following thickness limitations are given in this standard:
-   for seamless hollow sections up to and including 65 mm;
-   for HFW hollow sections up to and including 25,4 mm.
Greater thicknesses can be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex E on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 770 MPa are specified together with impact properties at temperatures down to -40 °C.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-4:2019+A1:2023(Main)
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019+A1:2022

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-6:2019+A1:2023(Main)
Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10025-6:2019+A1:2022

This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 683-3:2022(Main)
Heat-treatable steels, alloy steels and free-cutting steels - Part 3: Case-hardening steels (ISO 683-3:2022)
EN ISO 683-3:2022

This document specifies the technical delivery requirements for
— semi-finished products, hot formed (e.g. blooms, billets, slabs) (see NOTE 1),
— bars (see NOTE 1),
— wire rod,
— finished flat products, and
— hammer or drop forgings (see NOTE 1)
manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one
of the heat-treatment conditions given for the different types of products in Table 1 and in one of the
surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of case-hardened machine parts.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and
hammerforged bars are covered under semi-finished products or bars and not under the term “hammer and drop
forgings”.
NOTE 2 For International Standards relating to steels conforming with the requirements for the chemical
composition in Table 3, however, supplied in other product forms or treatment conditions than given above or
intended for special applications, and for other related International Standards, see the Bibliography.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10132:2021(Main)
Cold rolled narrow steel strip for heat treatment - Technical delivery conditions
EN 10132:2021

This document specifies the technical delivery conditions for cold rolled narrow steel strip made of non alloy and alloy steel grades in the form of coils and cut lengths in rolling widths less than 600 mm. Cold rolled narrow steel strip is available in grades of case hardening steel and of steels for quenching and tempering for general and special applications particularily springs.
—   Case hardening steels in thicknesses up to and including 10 mm;
—   Steels for quenching and tempering in thicknesses up to and including 6 mm in the conditions annealed (+A), annealed and skin passed (+LC) or cold rolled (+CR);
—   Steels in the quenched and tempered condition (+QT) in thicknesses between 0,30 mm and 3,00 mm.
In special cases supplementary requirements or deviations with respect to this document can be agreed between the purchaser and the supplier at the time of enquiry and order (see 5.2 and Annex A).
In addition to the requirements of this document, the general technical delivery requirements specified in EN 10021 apply.
This document does not cover cold rolled flat products for which separate standards exist, e.g.:
—   Cold rolled uncoated low carbon steel narrow strip for cold forming (EN 10139);
—   Cold rolled steel flat products with higher yield strength for cold forming (EN 10268).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 683-5:2021(Main)
Heat treatable steels, alloy steels and free-cutting steels - Part 5: Nitriding steels (ISO 683-5:2017)
EN ISO 683-5:2021

This document gives the technical delivery requirements for
—   semi-finished products, e.g. blooms, billets, slabs (see note 1),
—   bars (see note 1),
—   wire rod,
—   hot-rolled plates (see note 2), and
—   hammer or drop forgings (see note 1)
manufactured from the nitriding steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1, rows 2 to 5, and in one of the surface conditions given in Table 2.
The steels are generally intended for the fabrication of quenched and tempered and, subsequently, nitriding machine parts.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-5:2019(Main)
Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
EN 10025-5:2019

Part 5 of this document, in addition to part 1, specifies requirements for flat and long products of hot rolled steels with improved atmospheric corrosion resistance in the grades and qualities given in Tables 2 and 3 (chemical composition) and Tables 4 and 5 (mechanical properties) in the usual delivery conditions as given in 6.3.
The thicknesses in which products of the steel grades and qualities specified in this document may be supplied are given in Table 1.
In addition to EN 10025-1:2004 the steels specified in this document are especially intended for use in welded, bolted and riveted components which shall have enhanced resistance to atmospheric corrosion, for service at ambient temperatures (subject to the restrictions described in 7.4.1).
The steels specified in this Part 5 are not intended to be heat treated except products delivered in the delivery condition +N. Stress relief annealing is permitted (see also the NOTE in 7.3.1.1 of EN 10025-1:2004). Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-4:2019(Main)
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019

Part 4 of this document, in addition to Part 1, specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 2 to 4 (chemical composition) and Tables 5 to 7 (mechanical properties) in thickness < 120 mm for flat products and in thickness < 150 mm for long products.
In addition to EN 10025-1 the steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-3:2019(Main)
Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10025-3:2019

Part 3 of this document, in addition to part 1, specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in Tables 2 to 4 (chemical composition) and Tables 5 to 7 (mechanical properties) in thickness < 250 mm for grades S275, S355 and S420 and in thickness < 200 mm for grade S460.
In addition to EN 10025-1:2004 the steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-2:2019(Main)
Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-2:2019

Part 2 of this document, in addition to Part 1, specifies the technical delivery conditions for flat and long products and semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 2 to 6 (chemical composition) and Tables 7 to 9 (mechanical properties) in the delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 3 and 5) (chemical composition) and Table 8 (mechanical properties). This document does not apply to structural hollow sections and tubes (see EN 10210-1 and EN 10219-1).
The technical delivery conditions apply to thicknesses > 3 mm and < 150 mm for long products of steel grade S450J0. The technical delivery conditions apply to thicknesses < 250 mm for flat and long products of all other grades and qualities. In addition for flat products of qualities J2 and K2 the technical conditions apply to thicknesses < 400 mm.
Products made of steel grades S185, E295, E335 and E360 cannot be CE marked.
The steels specified in this Part 2 are not intended to be heat treated except products delivered in delivery condition +N. Stress relief annealing is permitted (see also the NOTE in 7.3.1.1 of EN 10025-1:2004). Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
NOTE 1   Semi-finished products which are to be converted to rolled finished products conforming to this document should be the subject of special agreement at the time of the enquiry and order. The chemical composition can also be agreed at the time of the order, however the values should be within the limits of Tables 2 and 3.
NOTE 2   For certain grades and product forms suitability for particular applications may be specified at the time of the enquiry and order (see 7.4.2, 7.4.3 and Table 10).

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day