EN 14410:2003
(Main)Self adhesive tapes - Measurement of breaking strength and elongation at break
Self adhesive tapes - Measurement of breaking strength and elongation at break
This European Standard specifies methods to measure the breaking strength and elongation at break of a self adhesive tape when it is subjected to a tensile force sufficient to cause it to break.
The breaking strength of adhesive tape is of value as an indication of its uniformity and quality, and its ability to withstand stresses during application and use.
The elongation at break of the adhesive tape is of value as an indication of its uniformity and quality as well as a rough indication of its ability to conform to curved and irregular surfaces. It is usually determined at the same time as the breaking strength.
This test method describes a procedure for testing 12 mm or 24 mm wide samples cut from supplied rolls of self adhesive tapes. Alternatively rolls of self adhesive tape up to 50 mm wide may be directly tested in their original width. In these circumstances the practical breaking strength and elongation will be typical of the manufacturer's cut edges. When newly cut sample pieces are tested, because of the better cutting of the edges, the results can be higher than would be found on commercial tape.
Klebebänder - Messung der Bruchkraft und der Reißdehnung
Rubans auto-adhésifs - Mesurage de la résistance à la rupture et de l'allongement à la rupture
La présente Norme européenne spécifie des méthodes pour mesurer la résistance à la rupture et l'allongement à la rupture d'un ruban auto-adhésif lorsqu'il est soumis à une force de traction suffisante pour provoquer sa rupture.
La résistance à la rupture d'un ruban adhésif est intéressante pour connaître l'uniformité, la qualité et l'aptitude de ce ruban à supporter des efforts au cours de l'application et en service.
L'allongement à la rupture d'un ruban adhésif est intéressant pour connaître l'uniformité et la qualité du ruban, et il donne également une indication grossière de l'aptitude du ruban à s'adapter à des surfaces courbes et irrégulières. L'allongement est généralement déterminé en même temps que la résistance à la rupture.
La présente méthode d'essai décrit un mode opératoire pour soumettre à l'essai des échantillons de rouleaux de rubans auto-adhésifs de 12 mm ou 24 mm de largeur. Une autre solution consiste à soumettre à l'essai des rouleaux de ruban directement dans leur largeur initiale (au plus 50 mm). Dans ces conditions, la résistance et l'allongement à la rupture sont, en pratique, caractéristiques de la découpe des bords effectuée en usine. Lorsque les essais portent sur des échantillons fraîchement découpés, les résultats obtenus peuvent se révéler supérieurs à ceux qui l'auraient été en utilisant des rubans du commerce en raison de la meilleure découpe des bords.
Samolepilni trakovi - Merjenje utržne trdnosti in raztezka ob utrgu
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Samolepilni trakovi – Merjenje utržne trdnosti
in raztezka ob utrguKlebebänder - Messung der Bruchkraft und der ReißdehnungRubans auto-adhésifs - Mesurage de la résistance a la rupture et de l'allongement a la ruptureSelf adhesive tapes - Measurement of breaking strength and elongation at break83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 14410:2003SIST EN 14410:2003en01-julij-2003SIST EN 14410:2003SLOVENSKI
STANDARDSIST EN 1941:1997SIST EN 1940:19971DGRPHãþD
SIST EN 14410:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14410March 2003ICS 83.180English versionSelf adhesive tapes - Measurement of breaking strength andelongation at breakRubans auto-adhésifs - Mesurage de la résistance à larupture et de l'allongement à la ruptureKlebebänder - Messung der Bruchkraft und derReißdehnungThis European Standard was approved by CEN on 6 December 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14410:2003 ESIST EN 14410:2003
EN 14410:2003 (E)2ContentspageForeword.3Introduction.41Scope.52Terms and definitions.53Significance and use.54Principle.55Apparatus.66Test sample and test pieces.77Procedure.78Expression of results.89Test report.8SIST EN 14410:2003
EN 14410:2003 (E)3ForewordThis document (EN 14410:2003) has been prepared by Technical Committee CEN/TC 253 "Self adhesive tapes",the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by September 2003, and conflicting national standards shall be withdrawn at thelatest by September 2003.This document supersedes EN 1940:1996 and EN 1941:1996.This European standard has been revised in conjunction with AFERA (Association of European self Adhesivetapes Manufacturers) in Europe and PSTC (Pressure Sensitive Tape Council) in USA with the purpose to producea standard which will be acceptable in due course by ISO.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,Fra
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.