iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 16867:2020+A1:2021

(Main)

Building hardware - Mechatronic door furniture - Requirements and test methods

Building hardware - Mechatronic door furniture - Requirements and test methods

1.1   General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the possibility to control the locking and/or release part through an electronic authorization means. This can be operable by credentials (i.e. card, code, biometric).
The MDF according to this document is combined with locks according to EN 12209, EN 14846, prEN 15685 or may be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF may be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use, durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests conducted in addition to the performance testing specified by this document.
1.2   Exclusions
This document does not cover:
-   mechatronic cylinders according to EN 15684;
-   electromechanical operated locks and striking plates according to EN 14846.

Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und Prüfverfahren

1.1   Allgemeines
Dieses Dokument gilt für an der Tür angebrachte mechatronische Türbeschläge (MDF, en. mechatronic door furniture), die die Möglichkeit eröffnen, den Schließ  und/oder Öffnungsvorgang durch eine elektronische Freigabeberechtigung zu steuern. Das kann durch Berechtigungsnachweise erfolgen (d. h. Karte, Code, biometrisch).
Der diesem Dokument entsprechende MDF wird mit Schlössern nach EN 12209, EN 14846, EN 15685 kombiniert oder kann Teil eines Notausgangverschlusses nach EN 179, EN 1125 oder EN 13637 sein.
Der MDF kann eigenständig ausgeführt sein oder mit einem externen Steuersystem verbunden werden.
Das Dokument würde es ermöglichen, die MDF mittels mehrerer Eigenschaften, wie etwa Gebrauchskategorie, Dauerfunktionstüchtigkeit, Umweltbeständigkeit, Schutz und Typ der Betätigungsvorrichtung zu klassifizieren.
Die Eignung des MDF für die Verwendung an Feuer  oder Rauchschutzeinbauten wird durch Prüfungen des Feuerwiderstands bestimmt, die zusätzlich zu den in diesem Dokument festgelegten Leistungsprüfungen durchgeführt werden.
1.2   Ausnahmen
Dieses Dokument behandelt nicht:
-   mechatronische Schließzylinder nach EN 15684;
-   elektromechanisch betätigte Schlösser und Schließbleche nach EN 14846.

Quincaillerie pour le bâtiment - Poignée de porte mécatronique - Exigences et méthodes d'essai

1.1   Généralités
Le présent document s’applique aux ensembles plaques béquilles mécatroniques (MDF) montés sur un bloc-porte permettant de contrôler l'élément de verrouillage et/ou de déverrouillage sur une ouverture de porte d'un dispositif d'autorisation électronique. Ils peuvent être manœuvrés par des authentifiants (c'est-à-dire une carte, un code, la biométrique).
Le MDF conforme au présent document est combiné à des serrures conformes à l’EN 12209, l’EN 14846, l’EN 15685 ou peut faire partie d'un dispositif de sortie de secours selon l’EN 179, l’EN 1125 ou l’EN 13637.
Un MDF peut être indépendant ou raccordable à un système de contrôle externe.
Le présent document permet de classer les MDF en fonction de plusieurs caractéristiques telles que la catégorie d'utilisation, la durabilité, l'environnement, la sécurité, et le type de dispositif de manœuvre.
L’aptitude des MDF à l’utilisation sur des blocs-blocs-portes coupe-feu et/ou étanches aux fumées est déterminée par des essais de résistance au feu, qui s’ajoutent aux essais de performance spécifiés dans le présent document.
1.2   Exclusions
Le présent document ne couvre pas :
-   les cylindres mécatroniques conformes à l’EN 15684 ;
-   les serrures et gâches électromécaniques conformes à l’EN 14846.

Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode (vključuje dopolnilo A1)

1.1   Splošno
Ta dokument se uporablja za mehatronsko okovje za vrata (MDF), nameščeno na vratni sklop, ki omogoča nadzor dela za zaklepanje in/ali odklepanje prek sredstev za elektronsko avtorizacijo. To je mogoče upravljati s poverilnicami (tj. kartica, koda, biometrija).
Mehatronsko okovje za vrata se skladno s tem dokumentom uporablja v kombinaciji s ključavnicami v skladu s standardi EN 12209, EN 14846 in prEN 15685 oziroma je lahko del naprave za zasilni izhod v skladu s standardom EN 179, EN 1125 ali EN 13637.
Mehatronsko okovje za vrata je lahko samostojno ali povezano z zunanjim nadzornim sistemom.
Dokument bi omogočal razvrstitev mehatronskega okovja za vrata po različnih značilnostih, kot so kategorija uporabe, trajnost, vpliv na okolje, varnost in vrsta naprave za upravljanje.
Ustreznost mehatronskega okovja za vrata za uporabo pri sestavih požarnih ali dimnih vrat se določi s preskusi požarne odpornosti, ki se izvajajo poleg preskušanja delovanja, določenega v tem dokumentu.
1.2   Izključitve
Ta dokument ne zajema:
–   mehatronskih cilindrov v skladu s standardom EN 15684;
–   elektromehanskih ključavnic in zapornih plošč v skladu s standardom EN 14846.

General Information

Status
Published
Publication Date
23-Nov-2021
Withdrawal Date
30-May-2022
ICS
91.190 - Building accessories
Technical Committee
CEN/TC 33 - Doors, windows, shutters and building hardware
Drafting Committee
CEN/TC 33/WG 4 - Building hardware
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
24-Nov-2021
Completion Date
24-Nov-2021
Ref Project
SIST EN 16867:2020+A1:2022 - Building hardware - Mechatronic door furniture - Requirements and test methods

Relations

Merged From
EN 16867:2020/prA1 - Building hardware - Mechatronic door furniture - Requirements and test methods
Effective Date
19-Jan-2023
Merged From
EN 16867:2020 - Building hardware - Mechatronic door furniture - Requirements and test methods
Effective Date
19-Jan-2023
Amended By
EN 16867:2020+A1:2021/prA2 - Building hardware - Mechatronic door furniture - Requirements and test methods
Effective Date
21-Dec-2022

Buy Standard

EN 16867:2020+A1:2022EN 16867:2020+A1:2022
PreviousNext
Standard
EN 16867:2020+A1:2022
English language
66 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16867:2020+A1:2022
01-januar-2022
Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode
(vključuje dopolnilo A1)
Building hardware - Mechatronic door furniture - Requirements and test methods
Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und
Prüfverfahren
Quincaillerie pour le bâtiment - Poignée de porte mécatronique - Exigences et méthodes
d'essai
Ta slovenski standard je istoveten z: EN 16867:2020+A1:2021
ICS:
91.190 Stavbna oprema Building accessories
SIST EN 16867:2020+A1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 16867:2020+A1:2022

---------------------- Page: 2 ----------------------
SIST EN 16867:2020+A1:2022


EN 16867:2020+A1
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2021
EUROPÄISCHE NORM
ICS 91.190 Supersedes EN 16867:2020
English Version

Building hardware - Mechatronic door furniture -
Requirements and test methods
Quincaillerie pour le bâtiment - Poignée de porte Schlösser und Baubeschläge - Mechatronische
mécatronique - Exigences et méthodes d'essai Türbeschläge - Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 27 January 2020 and includes Amendment 1 approved by CEN on 22
September 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16867:2020+A1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)

Contents Page
European foreword . 3
Introduction . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 10
5 Test — general and test apparatus . 27
6 Test methods — procedures . 27
7 Classification system . 54
8 Marking . 56
Annex A (normative) MDF suitable for use on fire resistant / smoke control doors . 57
Annex B (normative) Tool sets for attack resistance tests . 58
Annex C (informative) Table of test procedures . 60
Annex D (informative) Manufacturer’s declaration of compliance . 62
Annex E (informati
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16035:2023(Main)
Hardware performance sheet (HPS) - Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows
SIST EN 16035:2024

This document summarizes relevant results and classifications from tests of the fire and smoke resistance performance of building hardware in the format of a hardware performance sheet (HPS). This document provides guidance and requirements on the minimum data required as a basis for the preparation of EXAP reports for the interchangeability of building hardware on fire-retardant and/or smoke-tight doors and openable windows.
This document identifies the performance characteristics and the requirements for building hardware which can be found in the appropriate product standards.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-3:2023(Main)
Building hardware - Hardware for windows and door-height windows - Requirements and test methods - Part 3: Handles, primarily for Tilt and Turn, Tilt-First and Turn-Only hardware
SIST EN 13126-3:2023

This part of the EN 13126 series specifies the requirements and test procedures for durability, strength, security and functionality of handles.
This document is applicable to Tilt and Turn, Tilt-First and Turn-Only hardware for use on windows and door-height windows.
Handles can also be used on other opening types, e.g. on In-line Sliding, Tilt and Slide, Sliding Folding, horizontal and vertical-pivoting windows.
This document is not applicable to:
a)   operation devices, door handles for door latches and door locks (for this, refer to EN 1906);
b)   handles with handle length > 170 mm (refer to Figure B.1).

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17610:2022(Main)
Building hardware - Environmental product declarations - Product category rules complementary to EN 15804 for building hardware
SIST EN 17610:2022

This document provides product category rules (PCR) for Type III environmental declarations for:
- Building hardware products for opening and closing doors, gates, windows and shutters:
-- Lever handles and knob furniture (EN 1906);
-- Single-axis hinges (EN 1935);
-- Hardware for windows and door height windows (EN 13126 (all parts));
-- Fittings for shutters (e.g. EN 14648);
-- Controlled door closing devices, electrically powered hold-open devices for swing doors and door coordinator devices (EN 1154, EN 1155, EN 1158);
-- Hardware for sliding doors, folding doors and roll fronts (EN 1527, EN 15706);
-- Glass door gear;
- Building hardware products for locking and unlocking doors, gates, windows and shutters:
-- Mechanically operated locks and locking plates, multipoint locks, latches and locking plates (EN 12209, EN 15685 );
-- Cylinders for locks (EN 1303);
-- Padlocks and padlock fittings (EN 12320);
-- Mechanically operated push-button locksets (BS 8607);
-- Emergency exit devices operated by a lever handle or push pad, for use on escape routes and panic exit devices operated by a horizontal bar, for use on escape routes (EN 179, EN 1125);
- Electromechanical building hardware products:
-- Mechatronic cylinders (EN 15684);
-- Mechatronic padlocks (EN 16864);
-- Mechatronic door furniture (EN 16867);
-- Electromechanically operated locks and striking plates (EN 14846);
-- Electrically controlled exit systems for use on escape routes (EN 13637).
This document complements the core rules for the product category of construction products as defined in the European standard EN 15804:2012+A2:2019.
NOTE The assessment of social and economic performances at product level is not covered by this document.
The core PCR:
- defines the parameters to be declared and the way in which they are collated and reported;
- describes which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages;
- defines rules for the development of scenarios;
- includes the rules for calculating the Life Cycle Inventory and the Life Cycle Impact Assessment underlying the EPD, including the specification of the data quality to be applied;
- includes the rules for reporting the predetermined, environmental and health information that is not covered by Life Cycle Assessment (LCA) for the product, construction process(es) and construction service(s), as relevant;
- defines the conditions under which construction products can be compared based on the information provided by EPD.
For the EPD of construction services the same rules and requirements apply as for the EPD of construction products.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17814:2022(Main)
Building hardware - Master Key System data protection - Guidance
SIST-TS CEN/TS 17814:2022

This document specifies requirements and procedures to achieve and maintain protection of data and sensitive information related to mechanical Master Key Systems and other mechanical key systems where customer or application related data are being processed throughout the process of planning, production, installation, and maintenance.
The requirements and test methods for mechanical cylinder locks is covered by EN 1303.
Reference is made to EN 1303 and Annexes relating to Master Key Systems (MKS).
Requirements relating to the information security of key based and non-key based electronic cylinders are not covered.

  • Technical specification
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-16:2019/AC:2022(Corrigendum)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows
SIST EN 13126-16:2019/AC:2022

This part of EN 13126 specifies requirements and test methods for durability, strength, security and function of hardware for Lift and Slide windows and door height windows in accordance with common application as shown in informative Annex C, regardless of whether the hardware enables an additional tilt position.
NOTE 1   This document is also applicable to hardware systems, whereby the sash itself is not lifted but a gasket mechanism is moved.
NOTE 2   This document is also applicable to hardware systems, whereby the sash itself is not lifted but the sash is being moved parallel to the plane of the frame.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-14:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 14: Sash fasteners
SIST EN 13126-14:2022

This document specifies requirements and test methods for durability, strength, security, and function of sash fasteners for windows and door height windows.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-13:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 13: Sash balances
SIST EN 13126-13:2022

This document specifies requirements and test methods for durability, strength, security and function of sash balances.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-4:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 4: Espagnolettes
SIST EN 13126-4:2022

This document specifies requirements and test methods for durability, strength, security and function of espagnolettes and their striker plates for use on windows and door height windows.
Espagnolettes are defined as a locking mechanism for windows and door height windows that usually have a maximum handle movement of 90°.
This document does not include door bolts within the scope of EN 12051, or locks with latch and/or dead bolt within the scope of EN 12209 or multi-point locks within the scope of prEN 15685.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-1:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
SIST EN 13126-1:2022

This document specifies performance requirements for the strength and durability of hardware for the operation of movable sashes of windows and door height windows including requirements and test methods common to all hardware.
This document is applicable to the hardware suitable for windows and door height windows in Table 1, whatever the material used for the construction of the window.
Table 1 - Window opening-types
This document does not apply to the following:
—   fusible links;
—   hardware for lifting side-hung windows;
—   fixing devices that are used to assemble or install a fixed window;
—   devices that are used for the permanent fixing of a complete window into a building structure;
—   mechanisms for the pneumatic or hydraulic remote operation of windows;
—   single axis hinges (other than those, which provide a pivot-function for windows);
—   single axis hinges as covered in EN 1935;
—   hardware for sliding doors and folding doors as covered in EN 1527;
—   door and window bolts as covered in EN 12051.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1527:2019+A1:2021(Main)
Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods
SIST EN 1527:2019+A1:2022

This document specifies requirements for the design manual system sliding doors, sliding corner doors and folding doors of the bi-fold type and multi-panel folding doors but excluding doors and panels. Cycle tests, static load, initial friction and corrosion resistance tests are included for fittings and track only.
This document covers door gear for all industrial, commercial and residential sliding doors and folding doors.
This document does not cover the rollers for horizontal sliding and building hardware for inward or outward sliding folding windows (types N Q, R and S) in accordance with EN 13126-15, building hardware for Lift and Slide windows (type P) in accordance with EN 13126-16 and building hardware for Tilt and Slide windows (type T) in accordance with EN 13126-17.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day