EN 16867:2020+A2:2024
(Main)Building hardware - Mechatronic door furniture - Requirements and test methods
Building hardware - Mechatronic door furniture - Requirements and test methods
1.1 General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the possibility to control the locking and/or release part through an electronic authorization means. This can be operable by credentials (i.e. card, code, biometric).
The MDF according to this document is combined with locks according to EN 12209, EN 14846, prEN 15685 or may be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF may be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use, durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests conducted in addition to the performance testing specified by this document.
1.2 Exclusions
This document does not cover:
- mechatronic cylinders according to EN 15684;
- electromechanical operated locks and striking plates according to EN 14846.
Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und Prüfverfahren
1.1 Allgemeines
Dieses Dokument gilt für an der Tür angebrachte mechatronische Türbeschläge (MDF, en. mechatronic door furniture), die die Möglichkeit eröffnen, den Schließ und/oder Öffnungsvorgang durch eine elektronische Freigabeberechtigung zu steuern. Das kann durch Berechtigungsnachweise erfolgen (d. h. Karte, Code, biometrisch).
Der diesem Dokument entsprechende MDF wird mit Schlössern nach EN 12209, EN 14846, EN 15685 kombiniert oder kann Teil eines Notausgangverschlusses nach EN 179, EN 1125 oder EN 13637 sein.
Der MDF kann eigenständig ausgeführt sein oder mit einem externen Steuersystem verbunden werden.
Das Dokument würde es ermöglichen, die MDF mittels mehrerer Eigenschaften, wie etwa Gebrauchskategorie, Dauerfunktionstüchtigkeit, Umweltbeständigkeit, Schutz und Typ der Betätigungsvorrichtung zu klassifizieren.
Die Eignung des MDF für die Verwendung an Feuer oder Rauchschutzeinbauten wird durch Prüfungen des Feuerwiderstands bestimmt, die zusätzlich zu den in diesem Dokument festgelegten Leistungsprüfungen durchgeführt werden.
1.2 Ausnahmen
Dieses Dokument behandelt nicht:
- mechatronische Schließzylinder nach EN 15684;
- elektromechanisch betätigte Schlösser und Schließbleche nach EN 14846.
Quincaillerie pour le bâtiment - Poignée de porte mécatronique - Exigences et méthodes d'essai
1.1 Généralités
Le présent document s’applique aux ensembles plaques béquilles mécatroniques (MDF) montés sur un bloc-porte permettant de contrôler l'élément de verrouillage et/ou de déverrouillage sur une ouverture de porte d'un dispositif d'autorisation électronique. Ils peuvent être manœuvrés par des authentifiants (c'est-à-dire une carte, un code, la biométrique).
Le MDF conforme au présent document est combiné à des serrures conformes à l’EN 12209, l’EN 14846, l’EN 15685 ou peut faire partie d'un dispositif de sortie de secours selon l’EN 179, l’EN 1125 ou l’EN 13637.
Un MDF peut être indépendant ou raccordable à un système de contrôle externe.
Le présent document permet de classer les MDF en fonction de plusieurs caractéristiques telles que la catégorie d'utilisation, la durabilité, l'environnement, la sécurité, et le type de dispositif de manœuvre.
L’aptitude des MDF à l’utilisation sur des blocs-blocs-portes coupe-feu et/ou étanches aux fumées est déterminée par des essais de résistance au feu, qui s’ajoutent aux essais de performance spécifiés dans le présent document.
1.2 Exclusions
Le présent document ne couvre pas :
- les cylindres mécatroniques conformes à l’EN 15684 ;
- les serrures et gâches électromécaniques conformes à l’EN 14846.
Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode (vključno z dopolnilom A2)
Ta dokument se uporablja za mehatronsko okovje za vrata (MDF), nameščeno na vratni sklop, ki omogoča nadzor dela za zaklepanje in/ali odklepanje prek sredstev za elektronsko avtorizacijo. To je mogoče upravljati s poverilnicami (tj. kartica, koda, biometrija).
Mehatronsko okovje za vrata se skladno s tem dokumentom uporablja v kombinaciji s ključavnicami v skladu s standardi EN 12209, EN 14846 in prEN 15685 oziroma je lahko del naprave za zasilni izhod v skladu s standardom EN 179, EN 1125 ali EN 13637.
Mehatronsko okovje za vrata je lahko samostojno ali povezano z zunanjim nadzornim sistemom.
Dokument bi omogočal razvrstitev mehatronskega okovja za vrata po različnih značilnostih, kot so kategorija uporabe, trajnost, vpliv na okolje, varnost in vrsta naprave za upravljanje.
Ustreznost mehatronskega okovja za vrata za uporabo pri sestavih požarnih ali dimnih vrat se določi s preskusi požarne odpornosti, ki se izvajajo poleg preskušanja delovanja, določenega v tem dokumentu.
1.2 Izključitve
Ta dokument ne zajema:
– mehatronskih cilindrov v skladu s standardom EN 15684;
– elektromehanskih ključavnic in zapornih plošč v skladu s standardom EN 14846.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode
(vključno z dopolnilom A2)
Building hardware - Mechatronic door furniture - Requirements and test methods
Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und
Prüfverfahren
Quincaillerie pour le bâtiment - Poignée de porte mécatronique - Exigences et méthodes
d'essai
Ta slovenski standard je istoveten z: EN 16867:2020+A2:2024
ICS:
91.190 Stavbna oprema Building accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 16867:2020+A2
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 91.190 Supersedes EN 16867:2020+A1:2021
English Version
Building hardware - Mechatronic door furniture -
Requirements and test methods
Quincaillerie pour le bâtiment - Poignée de porte Schlösser und Baubeschläge - Mechatronische
mécatronique - Exigences et méthodes d'essai Türbeschläge - Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 27 January 2020 and includes Amendment 1 approved by CEN on 22
September 2021 and Amendment 2 approved by CEN on 3 November 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16867:2020+A2:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 10
5 Test — general and test apparatus . 27
6 Test methods — procedures . 28
7 Classification system . 54
8 Marking . 56
Annex A (normative) MDF suitable for use on fire resistant / smoke control doors . 57
Annex B (normative) Tool sets for attack resistance tests . 58
Annex C (informative) Table of test procedures . 60
Annex D (informative) Manufacturer’s declaration of compliance . 62
Annex E (informative) Examples of calculation of effective code variations for ICC . 64
Bibliography . 66
European foreword
This document (EN 16867:2020+A2:2024) has been prepared by Technical Committee CEN/TC 33
“Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2024, and conflicting national standards shall
be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 22 September 2021 and Amendment
2 approved by CEN on 3 November 2023.
This document supersedes #EN 16867:2020+A1:2021$.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !"
and #$.
This document is one of a series of European Standards dedicated to building hardware products.
European Standards for mechanically operated lever handles and knob furniture (EN 1906) are also
available.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these products throughout CEN
Member.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
The development of building hardware to include electrically and electronic operations and control has
introduced a large number of products on the market.
For locks and door furniture, the range of electrical or electronic components to be fitted to existing
mechanical locks or door furniture to a complete Mechatronic Door Furniture (MDF) has increased.
Also, complete units with lock and door furniture in unique combination to MDF occur frequently.
Typically, MDF is installed directly on the door leaf and includes all functions like operating the follower
of the lock, reading and decoding the credential and power.
Following components and units are covered by this document.
Type A: Handle or knob operated door furniture with electrically operated actuator, reading unit for
credential and power supply to be combined with a mechanical operated lock where the lock meets
EN 12209 or EN 15685.
Type B: Handle or knob operated door furniture with reading unit for credential and power supply to be
combined with electrically operated locks where the lock meets EN 14846.
This document does not cover electrically operated locks or striking plates in combination with an access
control system not fitted on the door.
This document provides the MDF with requirements for:
— category of use to ensure the performance during its normal use;
— durability to ensure good performance during lifetime;
— specification for system management;
— suitability for use on fire resistant/smoke controlled doors;
— environmental resistance for good performance during lifetime in different environmental
conditions;
— security for different types of credentials;
— attack resistance to ensure use on Burglary resistant doors;
— product information to give summary of the performance.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these devices throughout CEN
Member States.
It is assumed that MDF will conform to the legal regulations i.e. RED – Radio Equipment Directive
2014/53/EU.
On occasion, there could be a need for additional functions within the design of the MDF. Purchasers
should convince themselves that the products are suitable for their intended use. This is particularly
important when the operation of such additional functions is safety-related. Accordingly, this document
includes assessment of such features when they are included in the MDF design.
1 Scope
1.1 General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the
possibility to control the locking and/or release part through an electronic authorization means. This can
be operable by credentials (i.e. card, code, biometric).
The MDF, according to this document, is combined with locks according to EN 12209, EN 14846,
EN 15685 or can be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF can be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use,
durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests
conducted in addition to the performance testing specified by this document.
1.2 Exclusions
This document does not cover:
— mechatronic cylinders according to EN 15684;
— electromechanical operated locks and striking plates according to EN 14846.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 636:2012+A1:2015, Plywood — Specifications
EN 1303, Building hardware — Cylinders for locks - Requirements and test methods
EN 1634-1, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware — Part 1: Fire resistance test for door and shutter assemblies and openable
windows
EN 1634-2, Fire resistance and smoke control tests for door, shutter and openable window assemblies and
elements of building hardware — Part 2: Fire resistance characterisation test for elements of building
hardware
EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware — Part 3: Smoke control test for door and shutter assemblies
EN 1670:2007, Building hardware — Corrosion resistance — Requirements and test methods
EN 1906:2012, Building hardware — Lever handles and knob furniture — Requirements and test methods
EN 14846, Building hardware — Locks and latches — Electromechanically operated locks and striking
plates - Requirements and test methods
EN 15684, Building hardware — Mechatronic cylinders — Requirements and test methods
EN 15685, Building hardware — Requirements and test methods — Multipoint locks, latches and locking
plates — Characteristics and test methods
EN 60068-2-1, Environmental testing — Part 2-1: Tests — Test A: Cold
EN 60068-2-2, Environmental testing — Part 2-2: Tests — Test B: Dry heat
EN 60068-2-6, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal)
EN 60068-2-27, Environmental testing — Part 2-27: Tests — Test Ea and guidance: Shock
EN 60068-2-30, Environmental testing — Part 2-30: Tests — Test Db and guidance: Damp heat, cyclic (12
+ 12 hour cycle)
EN 60529, Degrees of protection provided by enclosures (IP Code)
EN 61000-4-2, Electromagnetic compatibility (EMC) — Part 4-2: Testing and measurement techniques -
Electrostatic discharge immunity test
EN 61000-4-3, Electromagnetic compatibility (EMC) — Part 4-3: Testing and measurement techniques —
Radiated, radio-frequency, electromagnetic field immunity test
EN 61000-4-4, Electromagnetic compatibility (EMC) — Part 4-4: Testing and measurement techniques —
Electrical fast transient/burst immunity test
EN 61000-4-5, Electromagnetic compatibility (EMC) — Part 4-5: Testing and measurement techniques —
Surge immunity test
EN 61000-4-11, Electromagnetic compatibility (EMC) — Part 4-11: Testing and measurement techniques -
Voltage dips, short interruptions and voltage variations immunity tests
EN 61000-4-29, Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques -
Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
EN ISO 10666, Drilling screws with tapping screw thread — Mechanical and functional properties
(ISO 10666)
EN ISO 15480, Fasteners — Hexagon washer head drilling screws with tapping screw thread (ISO 15480)
EN ISO 15481, Cross recessed pan head drilling screws with tapping screw thread (ISO 15481)
EN ISO 15482, Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482)
EN ISO 15483,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.