prEN ISO 6306

Chemical analysis of steel - Order of listing elements in steel standards (ISO 6306:2020)

This document specifies an order for listing elements within the chemical composition of steels and most other iron-based alloys, excluding foundry irons.

Chemische Analyse von Stahl - Reihenfolge der Elemente in Stahlnormen (ISO 6306:2020)

Analyse chimique des aciers - Ordre de report des éléments dans les normes d'acier (ISO 6306:2020)

Kemijska analiza jekla - Vrstni red navajanja elementov v standardih za jeklo (ISO 6306:2020)

General Information

• Status: Not Published
• Publication Date: 29-Jul-2025
• ICS: 77.040.30 - Chemical analysis of metals
• ICS: 77.080.20 - Steels
• Technical Committee: ECISS/TC 105 - Steels for heat treatment, alloy steels, free-cutting steels and stainless steels
• Drafting Committee: CEN/TC 459/SC 5/WG 1 - Steels for heat treatment, alloy steels and free cutting steels
• Current Stage: 4060 - Closure of enquiry - Enquiry
• Start Date: 24-Aug-2023
• Due Date: 29-Apr-2024
• Completion Date: 24-Aug-2023
• Ref Project: oSIST prEN ISO 6306:2023 - Chemical analysis of steel - Order of listing elements in steel standards (ISO 6306:2020)

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 6306:2023
01-julij-2023
Kemijska analiza jekla - Vrstni red navajanja elementov v standardih za jeklo (ISO
6306:2020)
Chemical analysis of steel - Order of listing elements in steel standards (ISO 6306:2020)
Chemische Analyse von Stahl - Reihenfolge der Elemente in Stahlnormen (ISO
6306:2020)
Analyse chimique des aciers - Ordre de report des éléments dans les normes d'acier
(ISO 6306:2020)
Ta slovenski standard je istoveten z: prEN ISO 6306
ICS:
77.040.30 Kemijska analiza kovin Chemical analysis of metals
77.080.20 Jekla Steels
oSIST prEN ISO 6306:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 6306:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 6306:2023
INTERNATIONAL ISO
STANDARD 6306
Second edition
2020-12
Chemical analysis of steel — Order of
listing elements in steel standards
Analyse chimique des aciers — Ordre de report des éléments dans les
normes d'acier
Reference number
ISO 6306:2020(E)
©
ISO 2020

---------------------- Page: 3 ----------------------
oSIST prEN ISO 6306:2023
ISO 6306:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 6306:2023
ISO 6306:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Order of listing elements in steel standards . 1
Bibliography . 3
© ISO 2020 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 6306:2023
ISO 6306:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 4, Heat
treata
...