iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12627:1999

(Main)

Industrial valves - Butt welding ends for steel valves

Industrial valves - Butt welding ends for steel valves

This European Standard specifies the dimensions of butt welding ends of steel valves DN 8 to DN 1400 designed to be butt welded to standardised pipes. Note: For the outside diameters and wall thickness of standardized pipes in accordance with ISO 4200.

Industriearmaturen - Anschweißenden für Armaturen aus Stahl

Diese Europäische Norm legt die Maße für Anschweißenden von Armaturen aus Stahl DN 8 bis DN 1400 fest, die an genormte Rohrleitungen angeschweißt werden. Anmerkung: Außendurchmesser und Wanddicken von genormten Rohren nach ISO 4200.

Appareils de robinetterie - Extrémités à souder en bout pour appareils de robinetterie en acier

La présente norme européenne spécifie les dimensions des extrémités à souder en bout des appareils de robinetterie en acier de DN 8 ` DN 1400 conçus pour être soudés en bout à des tubes normalisés. Note: Pour les diamètres extérieurs et les épaisseurs des tubes normalisés selon l'ISO 4200.

Industrijski ventili - Zunanji varilni nastavki za jeklene ventile

General Information

Status
Withdrawn
Publication Date
18-May-1999
Withdrawal Date
21-Nov-2017
ICS
23.060.01 - Valves in general
Technical Committee
CEN/TC 69 - Industrial valves
Drafting Committee
CEN/TC 69/WG 1 - Basic standards
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
22-Nov-2017
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 12627:2000 - Industrial valves - Butt welding ends for steel valves

Relations

Replaced By
EN 12627:2017 - Industrial valves - Butt welding ends for steel valves
Effective Date
09-Jul-2014

Buy Standard

EN 12627:2000EN 12627:2000
PreviousNext
Standard
EN 12627:2000
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Industrijski ventili - Zunanji varilni nastavki za jeklene ventileIndustriearmaturen - Anschweißenden für Armaturen aus StahlAppareils de robinetterie - Extrémités a souder en bout pour appareils de robinetterie en acierIndustrial valves - Butt welding ends for steel valves23.060.01Ventili na splošn
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 8233:2024(Main)
Thermoplastics valves - Torque - Test method (ISO 8233:2024)
SIST EN ISO 8233:2024

This document specifies a test method for the determination of the opening, closing and running torque of thermoplastics valves.
This document is applicable to all types of manually operable thermoplastics valves, with or without actuator, intended to be used for the transport of fluids.
NOTE 1        Examples of valve types tested with this method are in ISO 4437-4, ISO 16135, ISO 16136, ISO 16138, ISO 16139, ISO 16486-4, ISO 21787, EN 1555-4[13] and EN 12201-4 [14].
This document does not specify the relationship between the torque and its possible increase after prolonged use of the valve under a specific working condition or wear/chemical aggression of the materials.
NOTE 2        Concerning the chemical aggression of the materials, a collection of data is reported in ISO/TR 10358 concerning the endurance test necessary to confirm the ability of hand-operated plastics valves to withstand prolonged use with repeated opening and closing operations. Further information is provided in ISO 8659.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 19:2023(Main)
Industrial valves - Marking of metallic valves
SIST EN 19:2024

This document specifies the requirements for marking of industrial metallic valves. It defines the method of applying the markings, on the body, on a flange, on an identification plate or any other location.
When specified as a normative reference in a valve product or performance standard, this document is considered in conjunction with the specified requirements of that valve product or performance standard.
The marking requirements for plastic valves are not within the scope of this document.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5210:2023(Main)
Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2023)
SIST EN ISO 5210:2023

This document specifies the requirements for the attachment of multi-turn actuators to valves.
Throughout this document, “actuator” can be understood as “actuator and/or gearbox” providing a multi-turn and/or linear output.
It specifies:
—     flange dimensions necessary for the attachment of actuators to industrial valves [see Figure 1 a)] or to intermediate supports [see Figure 1 b)];
—     those driving component dimensions of actuators which are necessary to attach them to the driven components;
—     reference values for torque and thrust for flanges having the dimensions specified in this document.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5211:2023(Main)
Industrial valves - Part-turn actuator attachments (ISO 5211:2023)
SIST EN ISO 5211:2023

This document specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves.
The attachment of part-turn actuators to control valves in accordance with the requirements of this document is subject to an agreement between the supplier and the purchaser.
This document specifies:
—     flange dimensions necessary for the attachment of part-turn actuators to industrial valves [see Figures 1 a) and 1 c)] or to intermediate supports [see Figures 1 b) and 1 d)];
—     driving component dimensions of part-turn actuators necessary to attach them to the driven components;
—     reference values for torques for interfaces and for couplings having the dimensions specified in this document.
The attachment of the intermediate support to the valve is out of the scope of this document.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5117:2023(Main)
Automatic steam traps - Production and performance characteristic tests (ISO 5117:2023)
SIST EN ISO 5117:2023

This document specifies the production and performance relevant test requirements for automatic steam traps used for condensate removal/recovery services for optimized utilization of energy, in refinery, power generation or other general applications where steam is used as a medium of heat transfer.
The tests can be classified as production tests and performance characteristic tests and can be conducted to ensure the correct functioning of a steam trap or to evaluate the performance of a particular design. This document specifies the tests performed relative to each one of these two categories and briefly describes the corresponding test methods.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10497:2022(Main)
Testing of valves - Fire type-testing requirements (ISO 10497:2022)
SIST EN ISO 10497:2023

This document specifies fire type-testing requirements and a fire type-test method for soft- and metal-seated isolation valves with one or more obturators. It is not applicable to the testing requirements for valve actuators other than manually operated gearboxes or similar mechanisms when these form part of the normal valve assembly. Other types of valve actuators (e.g. electrical, pneumatic or hydraulic) can need special protection to operate in the environment considered in this valve test, and the fire testing of such actuators is outside the scope of this document.
This document specifies the measurement and assessment criteria for:
a) through-seat leakage;
b) external leakage;
c) cavity overpressure relief of double-seated valves;
d) operability.
This document specifies the rules whereby the fire-type testing qualification for a valve can be extended to untested sizes, pressure ratings and materials of construction of the same basic design type.
Fire test reports of valves tested according to previous editions of this document are acceptable when submitted together with the full and compliant fire test report as per 6.7 of the edition under which it was tested. Any data missing as required from 6.7 within the fire test report are accepted or rejected at the purchaser’s discretion.
NOTE       For the purposes of this document, the terms “fire type-test” and “fire test” are synonymous.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 23632:2022(Main)
Industrial valves - Design validation-testing of valves (ISO 23632:2021)
SIST EN ISO 23632:2022

Le présent document spécifie les exigences et les critères d’acceptation pour les essais de type, conformes aux conditions de conception, des robinets à tournant sphérique métalliques et robinets à papillon métalliques utilisés pour des services de sectionnement pour toutes les applications industrielles, et sert à valider la conception des produits sur 205 cycles.
Le présent document exclut les essais de dispositifs de sécurité, de robinets de régulation, de robinets en matériaux thermoplastiques, et des robinets pour l’alimentation en eau destinée à la consommation humaine et en eaux usées (par exemple la série EN 1074).
Le présent document définit la procédure permettant d’étendre la qualification de l’appareil de robinetterie soumis à l’essai à des désignations de dimensions et de pression non soumises à l’essai de la même gamme de produits.
Cet essai de type a pour objet de valider la performance de siège pour la relation pression/température précisée par le fabricant, qui figure dans la documentation technique du produit donnée par le fabricant. Cet essai de type vérifie les exigences de couple et le couple de manœuvre maximale admissible (MAST), tels que donnés dans la documentation technique du fabricant. Cet essai de type valide la durabilité de la performance de siège et le couple de manœuvre grâce à des cycles mécaniques et thermiques.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 28921-1:2022(Main)
Industrial valves - Isolating valves for low-temperature applications - Part 1: Design, manufacturing and production testing (ISO 28921-1:2022)
SIST EN ISO 28921-1:2022

This document specifies requirements for design, dimensions, material, fabrication and production testing of gate, globe, ball/plug and butterfly valve design types used as isolation valves and check valves for low-temperature applications.
This document is applicable to isolation valves for use in low and cryogenic temperature service where the design low-temperature service is -50 °C down to –196 °C.
This document does not apply to valves for cryogenic services, designed in accordance with ISO 21011, used with cryogenic vessels.
Where the requirements of this document vary from those given in the valve product standards, the requirements of this document apply.
This document is applicable to valves with body, bonnet, bonnet extension or cover made of metallic materials.
This document is applicable to:
—    valves of nominal sizes DN: 10; 15; 20; 25; 32; 40; 50; 65; 80; 100; 125; 150; 200; 250; 300; 350; 400; 450; 500; 600; 650; 700; 750; 800; 850; 900; 950; 1 000; 1 050; 1 200; 1 350; 1 400; 1 500; 1 600; 1 650; 1 800,
—    corresponding to nominal pipe sizes NPS: ⅜; ½; ¾; 1; 1 ¼; 1 ½; 2; 2 ½; 3; 4; 5; 6; 8; 10; 12; 14; 16; 18; 20; 24; 26; 28; 30; 32; 34; 36; 38; 40; 42; 48; 54; 56; 60; 64; 66; 72,
and applies to pressure designations:
—    PN 16; 25; 40; 100; 160; 250; 400,
—    Class 150; 300; 600; 800; 900; 1 500; 2 500.
NOTE       Not all type and size combination are available in all pressure ratings.
This document does not apply to safety valves and control valves.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 558:2022(Main)
Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - PN and Class designated valves
SIST EN 558:2022

This document specifies the “face-to-face” (FTF) and “centre-to-face” (CTF) dimensions for PN and Class designated metal valves used in flanged pipe systems.
This document covers valves with the following PN, Class and DN values:
—   PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400;
—   Class 125; Class 150; Class 250; Class 300; Class 600; Class 900; Class 1 500; Class 2 500;
—   DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1 000; DN 1 050; DN 1 200; DN 1 400; DN 1 600; DN 1 800; DN 2 000.
For valves in other shell materials than metal the same FTF and CTF dimensions can be used.
For relationship between DN and NPS, see Annex B.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12516-2:2014+A1:2021(Main)
Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
SIST EN 12516-2:2015+A1:2021

This European Standard specifies the method for the strength calculation of the shell with respect to internal pressure of the valve.

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day