Industrial valves - Butt welding ends for steel valves

This European Standard specifies the dimensions of butt welding ends of steel valves DN 8 to DN 1 400 designed to be butt welded to standardized pipes.
NOTE   The outside diameters and wall thickness of standardized pipes are in accordance with ISO 4200.

Industriearmaturen - Anschweißenden für Armaturen aus Stahl

Diese Europäische Norm legt die Maße für Anschweißenden von Armaturen aus Stahl DN 8 bis DN 1 400 fest, die an genormte Rohrleitungen angeschweißt werden.
ANMERKUNG   Außendurchmesser und Wanddicken von genormten Rohren nach ISO 4200.

Robinetterie industrielle - Extrémités à souder en bout pour appareils de robinetterie en acier

La présente Norme européenne spécifie les dimensions des extrémités à souder en bout pour appareils de robinetterie en acier DN 8 à DN 1 400 conçus pour être soudés en bout à des tubes normalisés.
NOTE   Les diamètres extérieurs et les épaisseurs des tubes normalisés sont conformes à l’ISO 4200.

Industrijski ventili - Zunanji varilni nastavki za jeklene ventile

Ta evropski standard določa dimenzije zunanjih varilnih nastavkov jeklenih ventilov od DN 8 do DN 1400, zasnovanih za soležno varjenje na standardizirane cevi.
OPOMBA: Zunanji premeri in debelina stene standardiziranih cevi so v skladu s standardom ISO 4200.

General Information

Status
Published
Publication Date
21-Nov-2017
Withdrawal Date
30-May-2018
Current Stage

Relations

Buy Standard

Standard
EN 12627:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 12627:2000
Industrijski ventili - Zunanji varilni nastavki za jeklene ventile
Industrial valves - Butt welding ends for steel valves
Industriearmaturen - Anschweißenden für Armaturen aus Stahl
Robinetterie industrielle - Extrémités à souder en bout pour appareils de robinetterie en
acier
Ta slovenski standard je istoveten z: EN 12627:2017
ICS:
23.060.01 Ventili na splošno Valves in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 12627
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 23.060.01 Supersedes EN 12627:1999
English Version
Industrial valves - Butt welding ends for steel valves
Robinetterie industrielle - Extrémités à souder en bout Industriearmaturen - Anschweißenden für Armaturen
pour appareils de robinetterie en acier aus Stahl
This European Standard was approved by CEN on 18 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12627 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols . 4
5 Requirements . 4
5.1 Selection of angle α . 4
5.2 Selection of other dimensions . 5
6 Designation. 9
Bibliography . 10

European foreword
This document (EN 12627:2017) has been prepared by Technical Committee CEN/TC 69 “Industrial
valves”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12627:1999.
The main changes compared to the previous edition are:
a) change of the tolerance value and diameter for DN 65 in Table 2;
b) introduction of angle α in Figures 2, 3, 4, 5 and 6.
c) editorial revision of this standard;
d) deletion of Annex A giving the basis document from which the previous edition was taken.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
1 Scope
This European Standard
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.