iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 492:1994

(Main)

Fibre-cement slates and their fittings for roofing - Product specification and test methods

Fibre-cement slates and their fittings for roofing - Product specification and test methods

This standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement fittings for roofing. It applies to fibre-cement slates with a height dimension not exceeding 850mm for overlapping assembly into coverings for roofs. For the purpose of this standard fibre-cement slates have been classified according to their bending moment. It identifies the water tightness.

Faserzement-Dachplatten und dazugehörige Formteile für Dächer - Produktspezifikationen und Prüfverfahren

Diese Norm regelt die technischen Anforderungen an Faserzement-Dachplatten und die dazugehörigen Formteile für Bedachungen; sie enthält weiterhin Verfahren zur Kontrolle und Prüfung sowie Annahmebedingungen. Sie gilt für Faserzement- Dachplatten bis zu einer maximalen Höhe H von 850mm für überlappende Eindeckungen von Dächern. Für die Zwecke dieser Norm werden Faserzement- Dachplatten entsprechend ihrem Biegemoment klassifiziert.

Ardoises en fibres-ciment et leurs accessoires en fibres-ciment pour toiture - Spécification du produit et méthodes d'essai

Cette Norme spécifie les prescriptions techniques et établit les méthodes de contrôle et d'essai ainsi que les conditions de réception des ardoises en fibres-ciment et de leurs accessoires en fibres-ciment pour les toîtures. Elle s'applique aux ardoises en fibres-ciment avec une hateur H ne dépassant pas 850 mm pour pose avec recouvrement, de couverture de toîture. Pour les besoins de cette norme les ardoises en fibres-ciment ont été classées en fonction de leur moment de flexion.

Vlaknatocementne strešne plošče in fazonski kosi - Specifikacije in preskusne metode

General Information

Status
Withdrawn
Publication Date
20-Feb-1994
Withdrawal Date
30-Nov-2004
ICS
91.100.40 - Products in fibre-reinforced cement
Technical Committee
CEN/TC 128 - Roof covering products for discontinuous laying and products for wall cladding
Drafting Committee
CEN/TC 128/SC 4 - Fibre cement products for roofing
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Dec-2004
Completion Date
01-Dec-2004
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 492:1998 - Fibre-cement slates and their fittings for roofing - Product specification and test methods

Relations

Replaced By
EN 492:2004 - Fibre-cement slates and fittings - Product specification and test methods
Effective Date
22-Dec-2008
Amended By
EN 492:1994/A1:1999 - Fibre-cement slates and their fittings for roofing - Product specification and test methods
Effective Date
22-Dec-2008
Corrected By
EN 492:1994/AC:1995 - Fibre-cement slates and their fittings for roofing - Product specification and test methods
Effective Date
22-Dec-2008
Corrected By
EN 492:1994/AC:1996 - Fibre-cement slates and their fittings for roofing - Productspecification and test methods
Effective Date
22-Dec-2008

Buy Standard

EN 492:1998EN 492:1998
PreviousNext
Standard
EN 492:1998
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 492:1998
01-april-1998
9ODNQDWRFHPHQWQHVWUHãQHSORãþHLQID]RQVNLNRVL6SHFLILNDFLMHLQSUHVNXVQH
PHWRGH
Fibre-cement slates and their fittings for roofing - Product specification and test methods
Faserzement-Dachplatten und dazugehörige Formteile für Dächer -
Produktspezifikationen und Prüfverfahren
Ardoises en fibres-ciment et leurs accessoires en fibres-ciment pour toiture -
Spécification du produit et méthodes d'essai
Ta slovenski standard je istoveten z: EN 492:1994
ICS:
91.060.20 Strehe Roofs
91.100.40 &HPHQWQLL]GHONLRMDþDQL] Products in fibre-reinforced
YODNQL cement
SIST EN 492:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 492:1998

---------------------- Page: 2 ----------------------

SIST EN 492:1998

---------------------- Page: 3 ----------------------

SIST EN 492:1998

---------------------- Page: 4 ----------------------

SIST EN 492:1998

---------------------- Page: 5 ----------------------

SIST EN 492:1998

---------------------- Page: 6 ----------------------

SIST EN 492:1998

---------------------- Page: 7 ----------------------

SIST EN 492:1998

---------------------- Page: 8 ----------------------

SIST EN 492:1998

---------------------- Page: 9 ----------------------

SIST EN 492:1998

---------------------- Page: 10 ----------------------

SIST EN 492:1998

---------------------- Page: 11 ----------------------

SIST EN 492:1998

---------------------- Page: 12 ----------------------

SIST EN 492:1998

---------------------- Page: 13 ----------------------

SIST EN 492:1998

---------------------- Page: 14 ----------------------

SIST EN 492:1998

---------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17468-2:2022(Main)
Fibre-cement products - Determination of pull through and shear resistance and bending strength calculations - Part 2: Profiled sheets
SIST EN 17468-2:2022

This document specifies test methods for pull through (tension/compression testing for fasteners through the sheets) and shear resistance of fibre-cement profiled sheets according to EN 494. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
It applies only to products as delivered.
The field of application for pull through resistance is defined in 7.6.
The field of application for shear resistance is defined in 8.6.
NOTE   For design purposes of fibre-cement profiled sheets in the final application, the failure modes pull-out and breaking of the fixings or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17468-1:2022(Main)
Fibre cement products - Determination of pull through and shear resistance and bending strength calculations - Part 1: Flat sheets
SIST EN 17468-1:2022

The document establishes an agreed method for evaluation of pull through resistance (tension/compression for fasteners through the sheets), shear resistance, bending strength and bending modulus of elasticity and suggests an approved safety concept of fibre-cement flat sheets for internal and external wall and ceiling finishes based on the experiences obtained over the last number of years in different countries. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
NOTE 1   For design purposes of fibre-cement flat sheets in the final application, the failure modes pull-out and breaking of the fixing or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. EN 14592) or ETA and substructure (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.
The results are also applicable for:
—   Coated or uncoated sheets manufactured at the same production facility as the tested sheets provided that the sheets are of the same type, have at least the same declared class according to EN 12467:2012+A2:2018, Table 6 and at least the same nominal thickness.
—   The test method can be applied to textured or non-textured fibre-cement flat sheets. The results of non-textured sheets are only applicable for textured sheets if the nominal minimum thickness of the textured sheet is at least the nominal thickness of the non-textured sheet.
—   The same type of fixing head or washer assembly where applicable if the diameter of the fixing head or washer is 0 mm to 2 mm larger than in the test.
—   The Shore A hardness of the sealing washer, where applicable, is ± 5 that of the washer used in the test, given that the washer thickness is at least as thick, the washer material at least as strong and the shape (dome or flat) of the washer equal to what has been tested.
NOTE 2   
A)   For pull-through resistance, if the diameter of the drilled hole through the fibre-cement sheet is 0 mm to 2 mm smaller or equal than in the test up to the diameter of the shank of the fastener, providing, during the test there is the required clearance hole around the shank of the fastener.
B)   For shear resistance, if the diameter of the drilled hole is equal to what has been tested.
It applies only to products as delivered.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12467:2012+A2:2018(Main + Amendment)
Fibre-cement flat sheets - Product specification and test methods
SIST EN 12467:2013+A2:2018

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 492:2012+A2:2018(Main + Amendment)
Fibre-cement slates and fittings - Product specification and test methods
SIST EN 492:2013+A2:2018

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 494:2012+A1:2015(Main + Amendment)
Fibre-cement profiled sheets and fittings - Product specification and test methods
SIST EN 494:2013+A1:2015

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied, after agreement, to curved sheets for specific applications.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15057:2006(Main)
Fibre cement profiled sheets - Impact resistance test method
SIST EN 15057:2006

This European Standard specifies a soft body impact test method for fibre-cement profiled sheets for roofing.
This European Standard applies to fibre-cement profiled sheets conforming to EN 494 and of length greater than or equal to 1,04 m.
It applies only to products as delivered.
NOTE   This European Standard can be applied, after agreement between manufacturer and purchaser, to curved sheets.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12467:2012+A1:2016/prA2(Amendment)
Fibre-cement flat sheets - Product specification and test methods
SIST EN 12467:2013+A1:2016/oprA2:2017

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 492:2012/FprA1:2015(Amendment)
Fibre-cement slates and fittings - Product specification and test methods
SIST EN 492:2013/kFprA1:2015

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
- roofing
- internal wall finishes
- external and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Amendment
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 494:2012/FprA1(Amendment)
Fibre-cement profiled sheets and fittings - Product specification and test methods
SIST EN 494:2013/kFprA1:2015

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more the following uses:
- roofing;
- internal wall finishes;
- external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiles sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in  5.1.1, with and without facotory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE: Some of these requirements can be applied, after agreement, to curved sheets for specific applications

  • Amendment
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12467:2012/FprA1:2015(Amendment)
Fibre-cement flat sheets - Product specification and test methods
SIST EN 12467:2013/kFprA1:2015

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
- internal wall and ceiling finishes,
- external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Amendment
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day