iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14275:2013

(Main)

Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers

Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers

This European Standard specifies a procedure for drawing, from fuel dispensers, samples of unleaded petrol and diesel fuel to be used for the assessment of automotive fuel quality in accordance with EN 14274. This European Standard does not cover the sampling of Liquefied Petroleum Gas (LPG).
WARNING: The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Kraftstoffe für Kraftfahrzeuge - Untersuchung der Qualität von Ottokraftstoff und Dieselkraftstoff - Probenahme an öffentlichen und gewerblichen Tankstellen

Diese Europäische Norm legt ein Verfahren für die Entnahme von Proben von unverbleitem Ottokraftstoff  und Dieselkraftstoff aus Zapfsäulen für den Kraftstoffqualitätsnachweis nach EN 14274 fest. Diese Europäische Norm behandelt nicht die Probenahme von Flüssiggas (LPG).
WARNUNG — Bei der Anwendung dieser Norm kann das Benutzen gefährlicher Substanzen und Ausrüstungen sowie das Durchführen gefährlicher Tätigkeiten erforderlich werden. Diese Norm nimmt nicht für sich in Anspruch, alle Sicherheitsprobleme, die bei ihrer Anwendung auftreten können, aufzuzeigen. Es liegt in der Verantwortung des Anwenders dieser Norm, entsprechende Sicherheitsmaßnahmen und Vorkehrungen zum Schutz der Gesundheit zu ergreifen.

Carburants pour automobiles - Évaluation de la qualité de l'essence et du carburant pour moteur diesel (gazole) - Échantillonnage au pistolet de distribution des pompes de stations-service des réseaux et des pompes privées hors réseaux

La présente Norme européenne prescrit une procédure d’échantillonnage des essences sans plomb et des carburants diesel (gazole) au niveau des points de distribution, pour utilisation dans le cadre du FQMS décrit dans l’EN 14274. La présente Norme ne traite pas le cas de l’échantillonnage des gaz de pétrole liquéfiés (GPL).
Avertissement - L'utilisation de la présente Norme européenne implique l'intervention de produits, d'opérations et d'équipements à caractère dangereux. La présente Norme européenne n’est pas censée aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Goriva za motorna vozila - Ocena kakovosti motornih bencinov in dizelskih goriv - Vzorčenje na bencinskih servisih in v distribucijskih skladiščih

Ta metoda določa metodo vzorčenja motornih bencinov in dizelskih goriv na bencinskih servisih.

General Information

Status
Published
Publication Date
12-Feb-2013
Withdrawal Date
30-Aug-2013
ICS
75.160.20 - Liquid fuels
Technical Committee
CEN/TC 19 - Petroleum products, lubricants and related products
Drafting Committee
CEN/TC 19 - Petroleum products, lubricants and related products
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
04-Jul-2024
Directive
98/70/EC - Quality of petrol and diesel fuels (Dir. 93/12/EEC amendment)
Ref Project
SIST EN 14275:2013 - Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers

Relations

Replaces
EN 14275:2003 - Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers
Effective Date
29-Jun-2011

Buy Standard

EN 14275:2013EN 14275:2013
PreviousNext
Standard
EN 14275:2013
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kraftstoffe für Kraftfahrzeuge - Untersuchung der Qualität von Ottokraftstoff und Dieselkraftstoff - Probenahme an öffentlichen und gewerblichen TankstellenCarburants pour automobiles - Évaluation de la qualité de l'essence et du carburant pour moteur diesel (gazole) - Échantillonnage au pistolet de distribution des pompes de stations-service des réseaux et des pompes privées hors réseauxAutomotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers75.160.20Liquid fuelsICS:Ta slovenski standard je istoveten z:EN 14275:2013SIST EN 14275:2013en,de01-april-2013SIST EN 14275:2013SLOVENSKI
STANDARDSIST EN 14275:20031DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14275
February 2013 ICS 75.160.20 Supersedes EN 14275:2003English Version
Automotive fuels - Assessment of petrol and diesel fuel quality -Sampling from retail site pumps and commercial site fuel dispensers
Carburants pour automobiles - Évaluation de la qualité de l'essence et du carburant pour moteur diesel (gazole) - Échantillonnage au pistolet de distribution des pompes de stations-service des réseaux et des pompes privées hors réseaux
Kraftstoffe für Kraftfahrzeuge - Untersuchung der Qualität von Ottokraftstoff und Dieselkraftstoff - Probenahme an öffentlichen und gewerblichen Tankstellen This European Standard was approved by CEN on 8 December 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14275:2013: ESIST EN 14275:2013

page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Sample containers and closures . 4 5 Safety requirements . 5 6 Sampling procedure . 5 7 Appointed organisations . 6 Annex A (informative)
Nozzle extensions for sampling petrol and their use . 7 Annex B (informative)
Sampling statement . 10 Bibliography. 12
3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1
outlet sample sample drawn from the dispensing pump using the normal pump nozzle 4 Sample containers and closures 4.1 Containers These shall be unused, preferably metallic, containers of the required capacity for execution of the intended testing program, constructed from lead-free material, with packing glands or welded joints, able to withstand normal internal pressures encountered during normal operations. The containers shall be equipped with an external fitting to enable them to be sealed. The container shall not have been treated with a petroleum-based rust-preventative. Certain test methods, especially for trace element analysis, require specific sampling equipment and containers made with material known not to interfere with the analysis.
Lead solder may be used for the attachment of external fittings. 4.2 Closures These aim at retaining the integrity of the sample. Insert disks may additionally be used to close the container outlet. Suitable closures include screw caps fitted with a washer resistant to the product being sampled. Cork or rubber washers shall not be used. SIST EN 14275:2013

5.2 Personnel drawing the samples shall be made aware of the potential hazards and be given instructions in safety precautions to be observed as set out in the Materials Safety Data Sheet. 5.3 Care shall be taken to avoid breathing petroleum vapours during the sampling. Protective gloves of hydrocarbon-insoluble materials, eye protection and clothing suitable to provide protection against all known hazards associated with the product shall be worn. 5.4 In order to avoid static electricity risks, special precautions shall be taken during the sampling operation. 5.4.1 Sampling shall not be carried out during periods of atmospheric electrical disturbance or hailstorms. 5.4.2 Foot wear and/or clothing capable of causing sparks shall not be worn in areas where flammable vapours are likely to be present. 5.4.3 In order to earth any static charge on their person, the person taking the samples shall touch some part of the fuel dispensing structure immediately before carrying out any sampling operation. 5.5 Samples shall not be taken during the supplying of the tank to which the pump to be sampled is connected. 5.6 Samples shall be clearly labelled to identify whether they contain petrol or diesel. 5.7 Samples shall be transported in accordance with
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13016-1:2024(Main)
Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE)
SIST EN 13016-1:2024

This document specifies a method for the determination of the air saturated vapour pressure (ASVP) (total vapour pressure), exerted in vacuo, by volatile, low viscosity petroleum products, components, ethanol blends up to 85 % (V/V), and feedstocks containing air. A dry vapour pressure equivalent (DVPE) can be calculated from the air containing vapour pressure (ASVP) measurement.
The conditions used in the test described in this document are a vapour-to-liquid ratio of 4:1 and a test temperature of 37,8 °C.
The equipment is not wetted with water during the test, and the method described is therefore suitable for testing samples with or without oxygenates; no account is taken of dissolved water in the sample.
The method described is suitable for testing air saturated samples with a DVPE between 15,5 kPa and 106,0 kPa; vapour pressures outside this range can be measured, but the precision has not been determined.
This document is applicable to fuels containing oxygenated compounds up to the limits stated in the relevant Council Directive 85/536/EEC [10], and for ethanol-fuel blends up to 85 % (V/V) ethanol.
NOTE   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent the mass and volume fractions, respectively.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of users of this document to take appropriate measures to ensure the safety and health of personnel prior to application of the document, and to determine the applicability of any other restrictions for this purpose.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12662-1:2024(Main)
Liquid petroleum products - Determination of total contamination - Part 1: Middle distillates and diesel fuels
SIST EN 12662-1:2024

This document specifies a method for the determination of the content of undissolved substances, referred to as total contamination, in middle distillates, in diesel fuels containing up to 30 % (V/V) fatty acid methyl esters (FAME). The working range is from 12 mg/kg to 26 mg/kg and it was established in an interlaboratory study by applying EN ISO 4259-1 [4].
This document in general is applicable to products having a kinematic viscosity not exceeding 8 mm2/s at 20 °C, or 5 mm2/s at 40 °C.
This test method can be used for paraffinic diesel fuels as specified in EN 15940, for diesel fuels containing more than 30 % (V/V) FAME and for petroleum products having a kinematic viscosity exceeding 8 mm2/s at 20 °C, or 5 mm2/s at 40 °C, however in such cases the precision of the test method has not been determined.
NOTE   For the purposes of this document, the term “% (V/V)” is used to represent the volume fraction, φ, of a material.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12662-2:2024(Main)
Liquid petroleum products - Determination of total contamination - Part 2: Fatty acid methyl esters
SIST EN 12662-2:2024

This document specifies a method for the determination of the content of undissolved substances, referred to as total contamination, in neat fatty acid methyl esters (FAME). The working range is from 5 mg/kg to 27 mg/kg and it was established in an interlaboratory study by applying EN ISO 4259-1 [1].
This document in general is applicable to FAME having a kinematic viscosity not exceeding 8 mm2/s at 20 °C, or 5 mm2/s at 40 °C, e.g. as specified in EN 14214 [2].
This test method can be used for FAME having a kinematic viscosity exceeding 8 mm2/s at 20 °C, or 5 mm2/s at 40 °C, however in such cases the precision of the test method has not been determined.
NOTE   For the purposes of this document, the term “% (V/V)” is used to represent the volume fraction, φ, of a material.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 589:2024(Main)
Automotive fuels - LPG - Requirements and test methods
SIST EN 589:2024

This document specifies requirements and test methods for marketed and delivered automotive LPG (commonly known as low pressure gas or liquefied petroleum gas).
This document is applicable to automotive LPG for use in LPG engine vehicles designed to run on automotive LPG.
NOTE   For the purposes of this European Standard, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction, µ, and the volume fraction, φ.
WARNING - Attention is drawn to the risk of fire and explosion when handling LPG and to the hazard to health arising through inhalation of excessive amounts of LPG.
LPG is a highly volatile hydrocarbon liquid which is normally stored under pressure. If the pressure is released large volumes of gas will be produced which form flammable mixtures with air over the range of approximately 2 % (V/V) to 10 % (V/V). This European Standard involves the sampling, handling and testing of LPG. Naked flames, unprotected electrical equipment electrostatic hazards etc. are sources of ignition for LPG.
LPG in liquid form can cause cold burns to the skin. National health and safety regulations can apply.
LPG is heavier than air and accumulates in cavities. There is a danger of suffocation when inhaling high concentrations of LPG.
CAUTION - One of the tests described in this document involves the operator inhaling a mixture of air and LPG vapour. Particular attention is drawn to the cautionary statement provided in A.1, where this method is referred to.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16389:2023(Main)
Automotive fuels - Paraffinic diesel fuel and blends with FAME - Background to the parameters required and their respective limits and determination
SIST-TP CEN/TR 16389:2024

This document explains the requirements and test methods for paraffinic diesel fuel from synthesis or hydrotreatment. Synthesis refers to XTL processes where X refers to various feedstocks for example Gas (G), Biomass (B) or Coal (C) and TL stands for To-Liquid. Hydrotreatment of vegetable oils and animal fats yield Hydrotreated Vegetable Oil (HVO). Paraffinic diesel fuel can be blended with up to 7,0 % (V/V) fatty acid methyl ester (FAME). This document provides background information to the final text of EN 15940 [1] and gives guidance and explanations to the producers, blenders, marketers and users of paraffinic automotive diesel fuel.
Paraffinic diesel fuel is a high quality, clean burning fuel with virtually no sulfur and aromatics. Paraffinic diesel fuel can be used in diesel engines, also to reduce regulated emissions. In order to have the greatest possible emissions reduction, a specific calibration is needed. Some types of paraffinic diesel fuel, at present notably HVO, can also offer a meaningful contribution to the target of increased non-crude derived and/or renewable content in the transportation fuel pool.
For general diesel engine operation, durability and warranty, paraffinic automotive diesel fuel needs a validation step to confirm the compatibility of the fuel with the vehicle, which for some existing engines still needs to be done. The vehicle manufacturer needs to be consulted before use.
NOTE 1   This document is directly related to EN 15940 and will be updated once further publications take place.
NOTE 2   Paraffinic diesel fuel is also used as a blending component in automotive diesel fuel. In that case, composition and properties of the final blends are defined by relevant fuel specification standards.
NOTE 3   For the purposes of this document, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction and the volume fraction.

  • Technical report
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17306:2023(Main)
Liquid petroleum products - Determination of distillation characteristics at atmospheric pressure - Micro-distillation
SIST EN 17306:2024

This document specifies a laboratory method for the determination of the distillation characteristics of light and middle distillates derived from petroleum and related products of synthetic or biological origin with initial boiling points above 20 °C and end-points below approximately 400 °C, at atmospheric pressure utilizing an automatic micro distillation apparatus.
This test method is applicable to such products as light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 20 % (V/V) ethanol, aviation gasolines, aviation turbine fuels, (paraffinic) diesel fuels, FAME (B100), diesel blends up to 30 % (V/V) fatty acid methyl esters (FAME), special petroleum spirits, naphtha’s, white spirits, kerosene’s, burner fuels, and marine fuels.
The test method is also applicable to hydrocarbons with a narrow boiling range, like organic solvents or oxygenated compounds.
The test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of user of this document to take appropriate measures to ensure the safety and health of personnel prior to application of the document, and to fulfil statutory and regulatory requirements for this purpose.
NOTE   For the purpose of this document, the expression "% (V/V)" is used to represent the volume fraction.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16906:2023(Main)
Liquid petroleum products - Determination of the ignition quality of diesel fuels - Fixed compression ratio engine method
SIST EN 16906:2023

This document specifies a test method for the determination of cetane numbers ("CN") of diesel fuels, using a standard single cylinder, four-stroke cycle, indirect injection engine. The cetane number provides a measure of the ignition characteristics of diesel fuels in compression ignition engines. The cetane number is determined at constant speed in a compression ignition test engine equipped with a swirl chamber.
The cetane number scale covers the range from 0 to 100, but typical testing is performed in the CN range from about 40 to about 75. The precision of this test method covers the CN range from 44 to about 66.
This document is applicable to distillate as well as paraffinic diesel fuels intended for use in diesel engines, including those containing up to a volume fraction of 10 % fatty-acid methyl esters (FAME), ignition-improvers or other diesel fuel additives.
When this engine test procedure is used for other fuels such as synthetics and vegetable oils, samples with fuel properties that interfere with the gravity-based pre-supply pressure to the fuel pump e.g. due to high viscosity can only be used to a limited extent. Precision data for such fuels are not available at this stage.
NOTE   The test method is also suitable for determining cetane numbers outside the range of the scope; however, the precision statement only applies for fuels in the specified range.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to take appropriate measures to ensure the safety and health of personnel prior to application of the document, and fulfil statutory and regulatory requirements for this purpose.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12156-1:2023(Main)
Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Part 1: Test method (ISO 12156-1:2023)
SIST EN ISO 12156-1:2023

This document specifies a test method using the high-frequency reciprocating rig (HFRR) with a digital camera, for assessing the lubricating property of petroleum-based middle distillate fuels, paraffinic diesel fuels, and biodiesel blends, with or without lubricity enhancing additives, and with HFRR wear scar diameters (WSDs) of 350 μm to 700 μm.
This test method applies to fuels used in diesel engines.
NOTE       It is not known if this test method can predict the performance of all additive/fuel combinations.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17867:2023(Main)
Petrol fuel for small internal combustion engines - Requirements and test methods
SIST EN 17867:2023

This document specifies requirements on petrol fuel for use as fuel in small engines, together with the methods to be applied for testing these properties.
This document specifies requirements for two types of petrol fuel having low aromatics and sulfur content:
- one type for use in four-stroke engines with separate lubrication; and
- one mixed petrol fuel type for use in mixture-lubricated engines.
Testing the properties of the added engine oil is out of the scope of this document.
NOTE For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15691:2023(Main)
Ethanol as a blending component for petrol - Determination of dry residue (involatile material) - Gravimetric method
SIST EN 15691:2023

This document specifies a procedure for the determination of dry residue in ethanol by gravimetric (desiccation) method in the range (10 to 25) mg/100 ml.
NOTE In an interlaboratory study [2] the method described has been tested at levels down to 3,5 mg/100 ml, but the precision appeared to be insufficient at such low levels.
WARNING - Use of this document can involve hazardous equipment, materials and operations. This method does not purport to address to all of the safety problems associated with its use. It is the responsibility of the user of this document to take appropriate measures to ensure the safety and health of personnel prior to the application of the document, and to fulfil statutory and regulatory restrictions for this purpose.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day