EN 13022-1:2006

Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing

This European Standard specifies requirements for the suitability for use of supported and unsupported glass products for use in “Structural Sealant Glazing” (SSG) applications. Four schematic drawings of SSG systems are shown in Figure 1 and three section drawings of an SSG type II system are shown in Figure 2 for illustration purposes. This European Standard on glass products is considered as a supplement to the requirements specified in the corresponding standards with regard to verifying the suitability for use in SSG systems.
Only soda lime silicate glasses are taken into consideration in this European Standard.
Plastic glazing is excluded from the scope of this European Standard.
Any glass products meeting the requirements of this European Standard are suitable for use in SSG systems as defined in ETAG 002 ) “Structural sealant glazing system”.
All glass products are installed and bonded into the support under controlled environmental conditions as described in Clause 5 of EN 13022-2:2006.
When the outer seal of the insulating glass unit has a structural function and/or is exposed to UV radiation without any protection, only silicone based sealant are permitted in the construction of the unit.

Glas im Bauwesen - Geklebte Verglasungen - Teil 1: Glasprodukte für SSG-Systeme - Einfach- und Mehrfachverglasungen mit und ohne Abtragung des Eigengewichtes

Diese Europäische Norm legt die Anforderungen an die Gebrauchstauglichkeit von Glasprodukten mit und
ohne Abtragung des Eigengewichtes für die Anwendung in SSG-Systemen fest. Bild 1 enthält vier
schematische Darstellungen von SSG-Verglasungen. Bild 2 zeigt drei Schnittzeichnungen eines SSG-Systems
des Typ II zur Erläuterung. Diese Europäische Norm für Glasprodukte stellt eine Ergänzung zu den
in den entsprechenden Normen festgelegten Anforderungen in Bezug auf den Nachweis der Eignung für
SSG-Systeme dar.
In dieser Europäischen Norm werden nur Verglasungen aus Kalk-Natronsilicatglas behandelt.
Kunststoff-Verglasungen sind nicht Gegenstand dieser Europäischen Norm.
Glasprodukte, die die Anforderungen dieser Europäischen Norm erfüllen, sind für den Einsatz in
SSG-Systemen nach ETAG 002 1) "Structural Sealant Glazing Systems " SSGS" geeignet.
Alle Glasprodukte werden unter kontrollierten Umgebungsbedingungen in die Unterkonstruktion eingebaut
und mit dieser verbunden, wie in EN 13022-2:2006, Abschnitt 5 beschrieben.
Wenn die äußere Dichtung des Isolierglases eine tragende Funktion hat und/oder ungeschützt der UV-Strahlung
ausgesetzt ist, dürfen nur Dichtungen auf Silikon-Basis beim Einbau der Verglasung verwendet
werden.

Verre dans la construction - Vitrage extérieur collé (VEC) - Partie 1 : Produits verriers pour les systèmes de vitrages extérieurs collés pour produits monolithiques et produits multiples calés et non calés

La présente Norme européenne spécifie les exigences relatives à l'aptitude à l'emploi des produits verriers calés et non calés destinés à être utilisés suivant la technique du « Vitrage Extérieur Collé » (VEC). Quatre dessins schématiques de VEC sont donnés dans la Figure 1 et six cas de système VEC de type I et II sont donnés dans le Figure 2 « Domaine d’application » à titre informatif.
Seuls les verres de silicate sodo-calcique sont pris en considération dans cette Norme européenne.
Le vitrage en plastique est exclu du domaine d'application de la présente norme.
Les produits verriers conformes aux exigences de la présente norme sont aptes à être utilisés dans des systèmes de vitrages extérieurs collés tels que définis dans le Guide d'Agrément Technique Européen 002 ) « Systèmes de vitrages extérieurs collés ».
Tous les produits verriers sont installés et collés sur le support sous les conditions de contrôle environnemental tels que définies à l'Article 5 de la EN 13022-2 : 2006.
Quand le scellement extérieur du vitrage isolant a une fonction structurelle et/ou est exposé au rayonnement UV sans aucune protection, seul les mastics à base de silicone sont permis dans l'assemblage de ce vitrage

Steklo v gradbeništvu – Strukturna zasteklitev – 1. del: Stekleni proizvodi za strukturne zasteklitve za podprte in nepodprte monolitne in sestavljene zasteklitve

General Information

• Status: Withdrawn
• Publication Date: 09-May-2006
• Withdrawal Date: 27-Apr-2010
• ICS: 81.040.20 - Glass in building
• Technical Committee: CEN/TC 129 - Glass in building
• Drafting Committee: CEN/TC 129/WG 16 - Structural glazing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 28-Apr-2010
• Completion Date: 28-Apr-2010
• Ref Project: SIST EN 13022-1:2006 - Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing

Relations

• Merged Into: EN 13022-1:2006+A1:2010 - Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing
• Effective Date: 30-Jan-2010
• Amended By: EN 13022-1:2006/FprA1 - Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing
• Effective Date: 04-Jul-2009

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazingSteklo v gradbeništvu – Strukturna zasteklitev – 1. del: Stekleni proizvodi za strukturne zasteklitve za podprte in nepodprte monolitne in sestavljene zasteklitveVerre dans la construction - Vitrage extérieur collé (VEC) - Partie 1 : Produits verriers pour les systemes de vitrages extérieurs collés pour produits monolithiques et produits multiples calés et non calésGlas im Bauwesen - Geklebte Verglasungen - Teil 1: Glasprodukte für SSG-Systeme - Einfach- und Mehrfachverglasungen mit und ohne Abtragung des EigengewichtesTa slovenski standard je istoveten z:EN 13022-1:2006SIST EN 13022-1:2006en81.040.20Steklo v gradbeništvuGlass in buildingICS:SLOVENSKI
STANDARDSIST EN 13022-1:200601-oktober-2006

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13022-1May 2006ICS 81.040.20 English VersionGlass in building - Structural sealant glazing - Part 1: Glassproducts for structural sealant glazing systems for supportedand unsupported monolithic and multiple glazingVerre dans la construction - Vitrage extérieur collé (VEC) -Partie 1 : Produits verriers pour les systèmes de vitragesextérieurs collés pour produits monolithiques et produitsmultiples calés et non calésGlas im Bauwesen - Geklebte Verglasungen - Teil 1:Glasprodukte für SSG-Systeme - Einfach- undMehrfachverglasungen mit und ohne Abtragung desEigengewichtesThis European Standard was approved by CEN on 13 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13022-1:2006: E

5.3 Monolithic glass or laminated glass, Situation 3 (see Figure 2).16 5.4 Assessment of the adhesion between the sealant and the glass.16 5.4.1 Clear float.16 5.4.2 Coated glass.16 5.4.3 Enamelled glass.17 5.4.4 Patterned glass.17 6 Design.17 6.1 Calculation of the thickness of the glass.17 6.2 Calculation of the height of the outer sealant of the insulating glass unit for supported and unsupported glazing.17 6.2.1 Supported insulating glass unit.17 6.3 Calculation of the height of the outer sealant of the insulating glass unit for unsupported glazing.21 6.3.1 Calculation of the height regarding the relevant combined load of the wind, snow and self weight and relevant combined load for wind, snow and self weight.21 6.3.2 Calculation of the height of the outer seal to bear the permanent shear loading.21 7 Minimum glass thickness.22 7.1 General case.22 7.2 Case of glass with worked edges.23

Assembly requirement.24 A.1 Setting blocks for glass panes or Insulating Glass Units.24 A.1.1 General case.24 A.1.2 Supporting the self-weight of a monolithic glass.26 A.2 Water drainage from the system.26 Bibliography.27

1) ETAG: European Technical Approval Guideline

Situation 1
Situation 2
Situation 3
Key 1 glass unit 2 inner seal 3 outer seal 4 finishing material 5 structural seal 6 structural seal adhesion surface 7 weather seal 8 setting block 9 adhesive spacer 10 structural seal support frame 11 laminated or monolithic glass unit Figure 2 — Scope NOTE The section drawings above are examples of structural sealant glazing system type II and IV.
...