EN ISO 294-2:2018

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:2018)

This document specifies a four-cavity mould, the type С ISO mould, for the injection moulding of small tensile bars measuring ≥ 60 mm × 10 mm × 3 mm (the type CW11 test specimen in ISO 20753).

Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 2: Kleine Zugstäbe (ISO 294-2:2018)

Dieses Dokument legt ein Vierfachwerkzeug fest, das ISO-Typ-C-Werkzeug zum Spritzgießen kleiner Zugstäbe ≥ 60 mm × 10 mm × 3 mm (Probekörpertyp CW11 nach ISO 20753).

Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques - Partie 2: Barreaux de traction de petites dimensions (ISO 294-2:2018)

Le présent document spécifie un moule à quatre empreintes, le moule ISO de type C, pour le moulage par injection des petits barreaux de traction mesurant ≥ 60 mm × 10 mm × 3 mm (l'éprouvette de type CW11 dans l'ISO 20753).

Polimerni materiali - Vbrizgavanje plastomernih preskušancev - 2. del: Mali paličasti preskušanci (ISO 294-2:2018)

Ta dokument določa kalup s štirimi luknjami, kalup ISO tip C, za vbrizgavanje malih paličastih preskušancev velikosti ≥ 60 mm × 10 mm × 3 mm (preskušanci tipa CW11 v standardu ISO 20753).

General Information

• Status: Published
• Publication Date: 18-Dec-2018
• Withdrawal Date: 29-Jun-2019
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/SC 1/WG 3 - Mechanical properties and preparation of test specimens
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 19-Dec-2018
• Completion Date: 19-Dec-2018
• Ref Project: SIST EN ISO 294-2:2019 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:2018)

Relations

• Replaces: EN ISO 294-2:1998/A1:2005 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:1996/Amd 1:2004)
• Effective Date: 26-Dec-2018
• Replaces: EN ISO 294-2:1998 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:1996)
• Effective Date: 26-Dec-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2019
1DGRPHãþD
SIST EN ISO 294-2:2000
SIST EN ISO 294-2:2000/A1:2006
3ROLPHUQLPDWHULDOL9EUL]JDYDQMHSODVWRPHUQLKSUHVNXãDQFHYGHO0DOL
SDOLþDVWLSUHVNXãDQFL,62
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small
tensile bars (ISO 294-2:2018)
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 2: Kleine
Zugstäbe (ISO 294-2:2018)
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques -
Partie 2: Barreaux de traction de petites dimensions (ISO 294-2:2018)
Ta slovenski standard je istoveten z: EN ISO 294-2:2018
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 294-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 294-2:1998
English Version
Plastics - Injection moulding of test specimens of
thermoplastic materials - Part 2: Small tensile bars (ISO
294-2:2018)
Plastiques - Moulage par injection des éprouvettes de Kunststoffe - Spritzgießen von Probekörpern aus
matériaux thermoplastiques - Partie 2: Barreaux de Thermoplasten - Teil 2: Kleine Zugstäbe (ISO 294-
traction de petites dimensions (ISO 294-2:2018) 2:2018)
This European Standard was approved by CEN on 18 December 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 294-2:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 294-2:2018) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 294-2:1998.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 294-2:2018 has been approved by CEN as EN ISO 294-2:2018 without any modification.

INTERNATIONAL ISO
STANDARD 294-2
Second edition
2018-12
Plastics — Injection moulding of
test specimens of thermoplastic
materials —
Part 2:
Small tensile bars
Plastiques — Moulage par injection des éprouvettes de matériaux
thermoplastiques —
Partie 2: Barreaux de traction de petites dimensions
Reference number
ISO 294-2:2018(E)
©
ISO 2018
ISO 294-2:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 294-2:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 1
4.1 Type С ISO mould . 1
4.2 Injection-moulding machine . 2
5 Procedure. 2
5.1 Conditioning of material . 2
5.2 Injection moulding .
...