iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10249-2:1995

(Main)

Cold formed sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions

Cold formed sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions

This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed non alloy steel sheet piles which are defined in EN 10249-1.

Kaltgeformte Spundbohlen aus unlegierte Stählen - Teil 2: Grenzabmaße und Formtoleranzen

In diesem Teil der Europäischen Norm sind die Grenzabmaße der Höhe, Breite, Wanddicke und Länge sowie die Grenzabweichungen des Schnitts rechtwinklig zur Längsachse, der Geradheit und der Masse von kaltgeformten, unlegierten Spundbohlen nach EN 10249-1 festgelegt.

Palplanches profilées à froid en aciers non alliés - Partie 2: Tolérances sur forme et dimensions

La présente partie de la présente norme européenne spécifie les tolérances relatives aux dimensions, à l'équerrage des extrémités, à la rectitude et à la masse des palplanches profilées à froid en aciers non alliés définies dans l'EN 10249-1.

Hladno oblikovana obešala iz nelegiranih jekel - 2. del: Mejni odstopki mer in tolerance oblik

General Information

Status
Withdrawn
Publication Date
14-Jun-1995
Withdrawal Date
16-Jul-2024
ICS
77.140.70 - Steel profiles
Technical Committee
ECISS/TC 103 - Structural steels other than reinforcements
Drafting Committee
ECISS/TC 10/SC 4 - Sheet piling
Current Stage
Ref Project
SIST EN 10249-2:1998 - Cold formed sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions

Relations

Replaced By
EN 10249-2:2024 - Cold formed steel sheet piles - Part 2: Tolerances on dimensions and shape
Effective Date
28-Jan-2023

Buy Standard

EN 10249-2:1998EN 10249-2:1998
PreviousNext
Standard
EN 10249-2:1998
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hladno oblikovana obešala iz nelegiranih jekel - 2. del: Mejni odstopki mer in tolerance oblikKaltgeformte Spundbohlen aus unlegierte Stählen - Teil 2: Grenzabmaße und FormtoleranzenPalplanches profilées a froid en aciers non alliés - Partie 2: Tolérances sur forme et dimensionsCold formed sheet piling of non alloy steels - Part 2: Tolerance
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10248-2:2024(Main)
Hot-rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
SIST EN 10248-2:2024

This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled steel sheet piles and is designed to be read in conjunction with EN 10248-1.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars.
This document also specifies options that can be agreed between the purchaser and the manufacturer at the time of the order and enquiry.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10249-2:2024(Main)
Cold formed steel sheet piles - Part 2: Tolerances on dimensions and shape
SIST EN 10249-2:2024

This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed steel sheet piles and is designed to be read in conjunction with EN 10249-1.
This document specifies the tolerances of cold formed steel sheet piles produced from hot rolled strip or sheet with a thickness equal to or greater than 3 mm.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, Omega-shaped and trench sheets.
This document also specifies options that can be agreed between the purchaser and the manufacturer at the time of the order and enquiry.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10248-1:2023(Main)
Hot-rolled steel sheet piles - Part 1: Technical delivery conditions
SIST EN 10248-1:2023

This document specifies the requirements for hot rolled steel sheet piles in respect of its chemical composition, mechanical properties and conditions of delivery.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars. The types of interlocks and the requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this document.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10164:2018(Main)
Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
SIST EN 10164:2018

This document specifies deformation properties perpendicular to the surface of the product.
This document may be applied as a supplement to all product standards for flat products and sections of fully killed steels, except stainless steels. It covers products having a nominal thickness (t) between 15 mm and 400 mm of steels with a specified minimum upper yield strength ReH or proof strength Rp0,2 ≤ 960 MPa ) for which improved through thickness properties are required.
This document may be applied to other steel types if agreed at the time of the order.
This document may be applied to products with thickness between 10 mm ≤ t <15 mm if agreed at the time of the order. See option 1.
This document may be applied to products with thickness t > 400 mm if agreed at the time of the order. See Option 2.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10056-1:2017(Main)
Structural steel equal and unequal leg angles - Part 1: Dimensions
SIST EN 10056-1:2017

This European Standard specifies requirements for the nominal dimensions of hot-rolled equal and unequal leg angles. This European Standard does not apply to angles with square roots. These requirements do not apply to equal and unequal leg angles rolled from stainless steel.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10365:2017(Main)
Hot rolled steel channels, I and H sections - Dimensions and masses
SIST EN 10365:2017

This European standard specifies the nominal dimensions and masses of the hot rolled steel channels, I and H sections.
The following shapes are covered by this standard:
Sections:
-   Parallel flange I sections IPE;
-   Wide flange beams HE;
-   Extra wide flange beams HL and HLZ;
-   Wide flange columns HD;
-   Wide flange bearing piles HP and UBP;
-   Universal beams UB;
-   Universal columns UC;
-   Taper flange I sections IPN and J.
Channels:
-   Parallel flange channels UPE and PFC;
-   Taper flange channels UPN, U and CH.
These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10163-1:2004/AC:2007(Corrigendum)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
SIST EN 10163-1:2005/AC:2007

CMC - Modification to Clause 2

  • Corrigendum
    2 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10163-1:2004(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
SIST EN 10163-1:2005

1.1   This European Standard specifies the general requirements for the surface condition of hot-rolled steel plates, wide flats and sections. It covers the requirements on the type, the permissible depth and the permissible size of the surface area affected by:
¾ discontinuities (imperfections ant defects) and
¾ repairs by grinding and/or welding.
1.2   This European Standard shall be applied so far as no other requirements for the surface condition exist in the appropriate material or product standard. The requirements laid down in the appropriate material or product standard shall always prevail.
1.3   This Part 1 of this European Standard covers the general delivery requirements for the surface condition of hot-rolled steel products such as:
¾ plates and wide flats, see Part 2;
¾ sections, see Part 3;

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10163-3:2004(Main)
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
SIST EN 10163-3:2005

This Part 3 in addition to Part 1 of this European Standard specifies the delivery requirements for surface condition of sections to which the European Standards mentioned in clause 2 apply and applies to all surfaces excluding edges.
NOTE   In this European Standard section toes (see EN 10055) are considered as part of the surfaces of a section.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10279:2000(Main)
Hot rolled steel channels - Tolerances on shape, dimensions and mass
SIST EN 10279:2000

This European Standard specifies requirements for the tolerances on dimensions, shape and mass of hot-rolled steel channels with tapered flanges or parallel flanges. These requirements do not apply to channels produced from stainless steel.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day