EN 12270:2013
(Main)Mountaineering equipment - Chocks - Safety requirements and test methods
Mountaineering equipment - Chocks - Safety requirements and test methods
This European Standard specifies safety requirements and test methods for chocks for use in mountaineering including climbing.
Bergsteigerausrüstung - Klemmkeile - Sicherheitstechnische Anforderungen und Prüfverfahren
Diese Europäische Norm legt sicherheitstechnische Anforderungen und Prüfverfahren für Klemmkeile fest, die beim Bergsteigen einschließlich Klettern verwendet werden.
Équipement d'alpinisme et d'escalade - Coinceurs - Exigences de sécurité et méthodes d'essai
La présente Norme européenne prescrit des exigences de sécurité et des méthodes d’essai relatives aux coinceurs utilisés en alpinisme et en escalade.
Gorniška oprema - Zatiči - Varnostne zahteve in preskusne metode
Ta evropski standard določa varnostne zahteve in preskusne metode za zatiče za uporabo v gorništvu, vključno s plezanjem.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bergsteigerausrüstung - Klemmkeile - Sicherheitstechnische Anforderungen und PrüfverfahrenEquipement d'alpinisme et d'escalade - Coinceurs - Exigences de sécurité et méthodes d'essaiMountaineering equipment - Chocks - Safety requirements and test methods97.220.40Oprema za športe na prostem in vodne športeOutdoor and water sports equipmentICS:Ta slovenski standard je istoveten z:EN 12270:2013SIST EN 12270:2013en,fr,de01-december-2013SIST EN 12270:2013SLOVENSKI
STANDARD
SIST EN 12270:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12270
November 2013 ICS 97.220.40 Supersedes EN 12270:1998English Version
Mountaineering equipment - Chocks - Safety requirements and test methods
Équipement d'alpinisme et d'escalade - Coinceurs - Exigences de sécurité et méthodes d'essai
Bergsteigerausrüstung - Klemmkeile - Sicherheitstechnische Anforderungen und Prüfverfahren This European Standard was approved by CEN on 28 September 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12270:2013 ESIST EN 12270:2013
EN 12270:2013 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Requirements .5 4.1 Design .5 4.2 Strength .5 5 Test methods .5 5.1 Test samples .5 5.2 Test apparatus for strength test .5 5.2.1 Layout .5 5.2.2 Adjustment . 12 5.3 Conditioning and test conditions . 12 5.4 Procedure . 13 5.4.1 Design . 13 5.4.2 Strength . 13 6 Marking
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.