EN ISO 13628-10:2006

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)

ISO 13628-10:2005 defines the technical requirements for safe, dimensionally and functionally interchangeable bonded flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements are specified for the design, material selection, manufacture, testing, marking and packaging of bonded flexible pipes, with reference to existing codes and standards where applicable.
ISO 13628-10:2005 applies to bonded flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends.
ISO 13628-10:2005 applies to pipes with a design pressure greater than or equal to 1,5 MPa (15 bar). ISO 13628-10:2005 can be used for lower design pressure pipes, though the requirements of these pipes have not been specifically addressed.
ISO 13628-10:2005 does not cover flexible pipes of unbonded structure nor to flexible pipe ancillary components and does not apply to flexible pipes for use in choke and kill line applications..
ISO 13628-10:2005 can be applied to flexible pipes that include non-metallic reinforcing layers, though no effort was made to address the specific and unique technological aspects of this product, and to a bonded construction pipe that includes a material or layer construction that is covered in ISO 13628-2.
ISO 13628-10:2005 can be applied to flexible pipes for pile hammer, gas flare, water supply and jetting applications, though no effort was made to address the specific and unique technological aspects relating to each of these requirements.

Erdöl- und Erdgasgewinnung - Konstruktion und Betrieb von Unterwasser-Produktionssystemen - Teil 10: Anforderungen an miteinander verklebte Leitungen (ISO 13628-10:2006)

Industries du pétrole et du gaz naturel - Conception et exploitation des systèmes de production immergés - Partie 10: Spécification pour canalisations flexibles composites (ISO 13628-10:2006)

L'ISO 13628-10:2005 définit les exigences techniques applicables à des canalisations flexibles composites, sûres, interchangeables du point de vue dimensionnel et fonctionnel, qui sont conçues et fabriquées selon des normes et des critères uniformes. Elle spécifie des exigences minimales relatives à la conception, au choix des matériaux, à la fabrication, aux essais, au marquage et au conditionnement des canalisations flexibles composites, en faisant référence, le cas échéant, à des codes et normes existants.
L'ISO 13628-10:2005 s'applique aux assemblages de canalisations flexibles composites constitués de tronçons de corps de canalisations flexibles munis de pièces d'extrémité fixées aux deux extrémités.
L'ISO 13628-10:2005 s'applique aux canalisations dont la pression de calcul est supérieure ou égale à 1,5 MPa (15 bar). Elle peut être utilisée pour des canalisations ayant une pression de calcul plus faible, même si les exigences correspondantes n'ont pas été spécifiquement traitées.
L'ISO 13628-10:2005 ne concerne pas les canalisations flexibles à structure non collée ni les canalisations flexibles destinées à être utilisées dans les applications de lignes de duse.
L'ISO 13628-10:2005 peut être appliquée aux canalisations flexibles qui comprennent des couches de renforcement non métalliques, même si aucun effort n'a été entrepris pour traiter les aspects technologiques particuliers et uniques de ces produits, et aux canalisations composites qui comprennent un matériau ou une structure de couche couverte par l'ISO 13628-2.
L'ISO 13628-10:2005 peut être appliquée à des canalisations flexibles utilisées pour des applications de marteau batteur, de torchère, d'alimentation en eau et d'ensouillage au jet, même si aucun effort n'a été entrepris pour traiter les aspects technologiques spécifiques et uniques correspondant à chacune de leurs exigences.

Industrija za predelavo nafte in zemeljskega plina - Načrtovanje in delovanje podvodnih proizvodnih sistemov - 10. del: Specifikacija za povezane gibke cevi (ISO 13628-10:2005)

General Information

• Status: Published
• Publication Date: 24-Oct-2006
• Withdrawal Date: 29-Apr-2007
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 25-Oct-2006
• Due Date: 06-Nov-2007
• Completion Date: 25-Oct-2006
• Ref Project: SIST EN ISO 13628-10:2007 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2007
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD1DþUWRYDQMHLQGHORYDQMH
SRGYRGQLKSURL]YRGQLKVLVWHPRYGHO6SHFLILNDFLMD]DSRYH]DQHJLENHFHYL
,62
Petroleum and natural gas industries - Design and operation of subsea production
systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)
Erdöl- und Erdgasgewinnung - Konstruktion und Betrieb von Unterwasser-
Produktionssystemen - Teil 10: Anforderungen an miteinander verklebte Leitungen (ISO
13628-10:2006)
Industries du pétrole et du gaz naturel - Conception et exploitation des systemes de
production immergés - Partie 10: Spécification pour canalisations flexibles composites
(ISO 13628-10:2006)
Ta slovenski standard je istoveten z: EN ISO 13628-10:2006
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 13628-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2006
ICS 75.180.10
English Version
Petroleum and natural gas industries - Design and operation of
subsea production systems - Part 10: Specification for bonded
flexible pipe (ISO 13628-10:2005)
Industries du pétrole et du gaz naturel - Conception et Erdöl- und Erdgasgewinnung - Konstruktion und Betrieb
exploitation des systèmes de production immergés - Partie von Unterwasser-Produktionssystemen - Teil 10:
10: Spécification pour canalisations flexibles composites Anforderungen an miteinander verklebte Leitungen (ISO
(ISO 13628-10:2005) 13628-10:2005)
This European Standard was approved by CEN on 6 October 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13628-10:2006: E
worldwide for CEN national Members.

Foreword
The text of ISO 13628-10:2005 has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 13628-
10:2006 by Technical Committee CEN/TC 12 "Materials, equipment and offshore structures for
petroleum, petrochemical and natural gas industries", the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2007, and conflicting national
standards shall be withdrawn at the latest by April 2007.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 13628-10:2005 has been approved by CEN as EN ISO 13628-10:2006 without
any modifications.
INTERNATIONAL ISO
STANDARD 13628-10
First edition
2005-10-01
Petroleum and natural gas industries —
Design and operation of subsea
production systems —
Part 10:
Specification for bonded flexible pipe
Industries du pétrole et du gaz naturel — Conception et exploitation des
systèmes de production immergés —
Partie 10: Spécification pour canalisations flexibles composites

Reference number
ISO 13628-10:2005(E)
©
ISO 2005
ISO 13628-10:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 13628-10:2005(E)
Contents Page
Foreword. v
Introduction . vi
1 Scope . 1
1.1 Purpose. 1
1.2 Products . 2
1.3 Applications . 2
2 Normative references . 2
3 Terms, definitions and abbreviations. 5
3.1 Terms and definitions. 5
3.2 Symbols and abbreviations . 10
4 Functional requirements. 11
4.1 General. 11
4.2 Overall requirements. 11
4.3 General design parameters . 12
4.4 Internal fluid parameters. 12
4.5 External environment . 14
4.6 System requirements . 14
5 Design requirements . 17
5.1 Loads and load effects. 17
5.2 Pipe design methodology . 20
5.3 Pipe structure design . 21
5.4 System design requirements. 26
6 Materials . 29
6.1 Material requirements. 29
6.2 Qualification requirements . 33
6.3 Quality assurance requirements . 39
7 Manufacturing requirements . 41
7.1 Quality assurance requirements . 41
7.2 Carcass . 42
7.3 Preparation of compound and calendering . 43
7.4 Elastomer winding. 44
7.5 Reinforcement armour layer. 45
7.6 Insulation layers. 45
7.7 End fitting . 45
7.8 Curing process. 47
7.9 Special processes. 48
7.10 Manufacturing tolerances . 50
7.11 Repairs. 50
8 Documentation. 51
8.1 General. 51
8.2 Design premise . 51
8.3 Design load report . 51
8.4 Design report. 51
8.5 Manufacturing quality plan . 52
8.6 Fabrication specification . 52
8.7 As-built documentation. 52
8.8 Operation manual . 53
ISO 13628-10:2005(E)
9 Factory acceptance tests . 54
9.1 General . 54
9.2 Gauge test. 55
9.3 Hydrostatic pressure test. 55
9.4 Electrical continuity and resistance tests . 56
9.5 Kerosene test. 56
9.6 Vacuum test. 56
...