Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)

ISO 868:2003 specifies a method for the determination of the indentation hardness of plastics and ebonite by means of durometers of two types: type A is used for softer materials and type D for harder materials. The method permits measurement either of the initial indentation or of the indentation after a specified period of time, or both. This method is an empirical method intended primarily for control purposes. No simple relationship exists between indentation hardness determined by this method and any fundamental property of the material tested. For specification purposes, it is recommended that ISO 48, Rubber, vulcanized or thermoplastic -- Determination of hardness (hardness between 10 IRHD and 100 IRHD), be used for the softer materials.

Plastiques et ébonite — Détermination de la dureté par pénétration au moyen d'un duromètre (dureté Shore)

L'ISO 868:2003 spécifie une méthode de détermination de la dureté par pénétration des plastiques et de l'ébonite au moyen de deux types de duromètres: le duromètre du type A est utilisé pour les produits les plus souples et le duromètre du type D pour les matériaux les plus durs. La méthode permet de mesurer soit la pénétration initiale, soit la pénétration après un temps spécifié, ou l'une et l'autre. Cette méthode est un essai empirique essentiellement conçu dans un but de contrôle. Il n'existe aucune relation simple entre la dureté par pénétration déterminée selon cette méthode et une caractéristique fondamentale quelconque du matériau soumis à l'essai. Pour les spécifications concernant les matériaux souples, il est recommandé d'utiliser l'ISO 48, Caoutchouc vulcanisé ou thermoplastique -- Détermination de la dureté (dureté comprise entre 10 DIDC et 100 DIDC).

General Information

Status
Published
Publication Date
13-Apr-2003
Current Stage
9093 - International Standard confirmed
Start Date
08-Apr-2025
Completion Date
08-Apr-2025
Ref Project

Relations

Buy Standard

Standard
ISO 868:2003 - Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) Released:4/14/2003
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 868:2003 - Plastics and ebonite -- Determination of indentation hardness by means of a durometer (Shore hardness)
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 868:2003 - Plastiques et ébonite — Détermination de la dureté par pénétration au moyen d'un duromètre (dureté Shore) Released:9/23/2003
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 868:2003 - Plastiques et ébonite -- Détermination de la dureté par pénétration au moyen d'un durometre (dureté Shore)
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


INTERNATIONAL ISO
STANDARD 868
Third edition
2003-03-01
Plastics and ebonite — Determination of
indentation hardness by means of a
durometer (Shore hardness)
Plastiques et ébonite — Détermination de la dureté par pénétration au
moyen d'un duromètre (dureté Shore)

Reference number
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2003 – All rights reserved

Contents Page
1 Scope . 1
2 Normative reference . 1
3 Principle . 1
4 Apparatus . 1
5 Test specimens . 4
6 Calibration . 4
7 Conditioning and testing atmospheres . 4
8 Procedure . 5
9 Test report . 5
©
ISO 2003 – All rights reserved iii

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 868 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical properties.
This third edition cancels and replaces the second edition (ISO 868:1985), which has been technically revised.
©
iv ISO 2003 – All rights reserved

INTERNATIONAL STANDARD ISO 868:2003(E)
Plastics and ebonite — Determination of indentation hardness by
means of a durometer (Shore hardness)
1 Scope
1.1 This International Standard specifies a method for the determination of the indentation hardness of plastics and
ebonite by means of durometers of two types: type A is used for softer materials and type D for harder materials (see
the Note to 8.2). The method permits measurement either of the initial indentation or of the indentation after a
specified period of time, or both.
NOTE The durometers and the methods specified in this International Standard are referred to as type A Shore and type D
Shore durometers and durometer methods, respectively.
1.2 This method is an empirical method intended primarily for control purposes. No simple relationship exists
between indentation hardness determined by this method and any fundamental property of the material tested. For
specification purposes, it is recommended that ISO 48, Rubber, vulcanized or thermoplastic — Determination of
hardness (hardness between 10 IRHD and 100 IRHD), be used for the softer materials.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, this publication do not
apply. However, parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent edition of the normative document indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing
3 Principle
A specified indenter is forced into the test material under specified conditions and the depth of penetration measured.
The indentation hardness is inversely related to the penetration and is dependent on the modulus of elasticity and the
viscoelastic properties of the material. The shape of the indenter, the force applied to it and the duration of its
application influence the results obtained so that there may be no simple relationship between the results obtained
with one type of durometer and those obtained with either another type of durometer or another instrument for
measuring hardness.
4Apparatus
Use either a type A or type D Shore durometer consisting of the following components:
4.1 Presser foot, with a hole of diameter 3mm± 0,5 mm centred at least 6 mm from any edge of the f
...


INTERNATIONAL ISO
STANDARD 868
Third edition
2003-03-01
Plastics and ebonite — Determination of
indentation hardness by means of a
durometer (Shore hardness)
Plastiques et ébonite — Détermination de la dureté par pénétration au
moyen d'un duromètre (dureté Shore)

Reference number
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2003 – All rights reserved

Contents Page
1 Scope . 1
2 Normative reference . 1
3 Principle . 1
4 Apparatus . 1
5 Test specimens . 4
6 Calibration . 4
7 Conditioning and testing atmospheres . 4
8 Procedure . 5
9 Test report . 5
©
ISO 2003 – All rights reserved iii

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 868 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical properties.
This third edition cancels and replaces the second edition (ISO 868:1985), which has been technically revised.
©
iv ISO 2003 – All rights reserved

INTERNATIONAL STANDARD ISO 868:2003(E)
Plastics and ebonite — Determination of indentation hardness by
means of a durometer (Shore hardness)
1 Scope
1.1 This International Standard specifies a method for the determination of the indentation hardness of plastics and
ebonite by means of durometers of two types: type A is used for softer materials and type D for harder materials (see
the Note to 8.2). The method permits measurement either of the initial indentation or of the indentation after a
specified period of time, or both.
NOTE The durometers and the methods specified in this International Standard are referred to as type A Shore and type D
Shore durometers and durometer methods, respectively.
1.2 This method is an empirical method intended primarily for control purposes. No simple relationship exists
between indentation hardness determined by this method and any fundamental property of the material tested. For
specification purposes, it is recommended that ISO 48, Rubber, vulcanized or thermoplastic — Determination of
hardness (hardness between 10 IRHD and 100 IRHD), be used for the softer materials.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, this publication do not
apply. However, parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent edition of the normative document indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing
3 Principle
A specified indenter is forced into the test material under specified conditions and the depth of penetration measured.
The indentation hardness is inversely related to the penetration and is dependent on the modulus of elasticity and the
viscoelastic properties of the material. The shape of the indenter, the force applied to it and the duration of its
application influence the results obtained so that there may be no simple relationship between the results obtained
with one type of durometer and those obtained with either another type of durometer or another instrument for
measuring hardness.
4Apparatus
Use either a type A or type D Shore durometer consisting of the following components:
4.1 Presser foot, with a hole of diameter 3mm± 0,5 mm centred at least 6 mm from any edge of the f
...


NORME ISO
INTERNATIONALE 868
Troisième édition
2003-03-01
Plastiques et ébonite — Détermination de la
dureté par pénétration au moyen d'un
duromètre (dureté Shore)
Plastics and ebonite — Determination of indentation hardness by means of
a durometer (Shore hardness)
Numéro de référence
PDF — Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de
l'ISO à l'adresse ci-après ou au comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Imprimé en Suisse
©
ii ISO 2003 – Tous droits réservés

Sommaire Page
1 Domaine d'application . 1
2 Référence normative . 1
3 Principe . 1
4 Appareillage . 1
5 Éprouvettes . 4
6 Étalonnage . 4
7 Atmosphères de conditionnement et d'essai . 5
8 Mode opératoire . 5
9 Procès-verbal d'essai . 5
©
ISO 2003 – Tous droits réservés iii

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en liaison
avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission électrotechnique
internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments de la présente Norme internationale peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne pas
avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 868 a été élaborée par le comité technique ISO/TC 61, Plastiques, sous-comité SC 2,
Propriétés mécaniques.
Cette troisième édition annule et remplace la deuxième édition (ISO 868:1985), dont elle constitue une révision
technique.
©
iv ISO 2003 – Tous droits réservés

NORME INTERNATIONALE ISO 868:2003(F)
Plastiques et ébonite — Détermination de la dureté par pénétration
au moyen d'un duromètre (dureté Shore)
1 Domaine d'application
1.1 La présente Norme internationale spécifie une méthode de détermination de la dureté par pénétration des
plastiques et de l'ébonite au moyen de deux types de duromètres: le duromètre du type A est utilisé pour les produits
les plus souples et le duromètre du type D pour les matériaux les plus durs (voir la Note de 8.2). La méthode permet
de mesurer soit la pénétration initiale, soit la pénétration après un temps spécifié, ou l'une et l'autre.
NOTE Les duromètres et les méthodes spécifiés dans la présente Norme internationale sont désignés respectivement sous le
nom de méthode au duromètre du type Shore A et méthode au duromètre du type Shore D.
1.2 Cette méthode est un essai empirique essentiellement conçu dans un but de contrôle. Il n'existe aucune
relation simple entre la dureté par pénétration déterminée selon cette méthode et une caractéristique fondamentale
quelconque du matériau soumis à l'essai. Pour les spécifications concernant les matériaux souples, il est
recommandé d'utiliser l'ISO 48, Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté (dureté
comprise entre 10 DIDC et 100 DIDC).
2Référence normative
Le document normatif suivant contient des dispositions qui, par suite de la référence qui y est faite, constituent des
dispositions valables pour la présente Norme internationale. Pour les références datées, les amendements ultérieurs
ou les révisions de cette publication ne s'appliquent pas. Toutefois, les parties prenantes aux accords fondés sur la
présente Norme internationale sont invitées à rechercher la possibilité d'appliquer l'édition la plus récente du
document normatif indiqué ci-après. Pour les références non datées, la dernière édition du document normatif en
référence s'applique. Les membres de l'ISO et de la CEI possèdent le registre des Normes internationales en
vigueur.
ISO 291:1997, Plastiques — Atmosphères normales de conditionnement et d'essai
3Principe
Un pénétreur spécifié est appliqué sur le matériau dans des conditions spécifiées et l'enfoncement est mesuré.
La dureté par pénétration est inversement proportionnelle à la pénétration et dépend du module d'élasticité et des
propriétés viscoélastiques du matériau. La forme du pénétreur, la force qui lui est appliquée et sa durée d'application
influent sur les résultats obtenus, de sorte qu'il ne peut exister de relation simple entre les résultats obtenus avec un
type de duromètre et ceux qui sont obtenus soit avec un autre type de duromètre, soit avec un autre instrument pour
mesurer la dureté.
4 Appareillage
Utiliser un duromètre soit du type Shore A, soit du type Shore D, comprenant les éléments suivants:
4.1 Pied-presseur, percé d'un trou de diamètre 3mm± 0,5 mmcentré à au moins 6 mm des bord
...


NORME ISO
INTERNATIONALE 868
Troisième édition
2003-03-01
Plastiques et ébonite — Détermination de la
dureté par pénétration au moyen d'un
duromètre (dureté Shore)
Plastics and ebonite — Determination of indentation hardness by means of
a durometer (Shore hardness)
Numéro de référence
PDF — Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de
l'ISO à l'adresse ci-après ou au comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Imprimé en Suisse
©
ii ISO 2003 – Tous droits réservés

Sommaire Page
1 Domaine d'application . 1
2 Référence normative . 1
3 Principe . 1
4 Appareillage . 1
5 Éprouvettes . 4
6 Étalonnage . 4
7 Atmosphères de conditionnement et d'essai . 5
8 Mode opératoire . 5
9 Procès-verbal d'essai . 5
©
ISO 2003 – Tous droits réservés iii

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en liaison
avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission électrotechnique
internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments de la présente Norme internationale peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne pas
avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 868 a été élaborée par le comité technique ISO/TC 61, Plastiques, sous-comité SC 2,
Propriétés mécaniques.
Cette troisième édition annule et remplace la deuxième édition (ISO 868:1985), dont elle constitue une révision
technique.
©
iv ISO 2003 – Tous droits réservés

NORME INTERNATIONALE ISO 868:2003(F)
Plastiques et ébonite — Détermination de la dureté par pénétration
au moyen d'un duromètre (dureté Shore)
1 Domaine d'application
1.1 La présente Norme internationale spécifie une méthode de détermination de la dureté par pénétration des
plastiques et de l'ébonite au moyen de deux types de duromètres: le duromètre du type A est utilisé pour les produits
les plus souples et le duromètre du type D pour les matériaux les plus durs (voir la Note de 8.2). La méthode permet
de mesurer soit la pénétration initiale, soit la pénétration après un temps spécifié, ou l'une et l'autre.
NOTE Les duromètres et les méthodes spécifiés dans la présente Norme internationale sont désignés respectivement sous le
nom de méthode au duromètre du type Shore A et méthode au duromètre du type Shore D.
1.2 Cette méthode est un essai empirique essentiellement conçu dans un but de contrôle. Il n'existe aucune
relation simple entre la dureté par pénétration déterminée selon cette méthode et une caractéristique fondamentale
quelconque du matériau soumis à l'essai. Pour les spécifications concernant les matériaux souples, il est
recommandé d'utiliser l'ISO 48, Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté (dureté
comprise entre 10 DIDC et 100 DIDC).
2Référence normative
Le document normatif suivant contient des dispositions qui, par suite de la référence qui y est faite, constituent des
dispositions valables pour la présente Norme internationale. Pour les références datées, les amendements ultérieurs
ou les révisions de cette publication ne s'appliquent pas. Toutefois, les parties prenantes aux accords fondés sur la
présente Norme internationale sont invitées à rechercher la possibilité d'appliquer l'édition la plus récente du
document normatif indiqué ci-après. Pour les références non datées, la dernière édition du document normatif en
référence s'applique. Les membres de l'ISO et de la CEI possèdent le registre des Normes internationales en
vigueur.
ISO 291:1997, Plastiques — Atmosphères normales de conditionnement et d'essai
3Principe
Un pénétreur spécifié est appliqué sur le matériau dans des conditions spécifiées et l'enfoncement est mesuré.
La dureté par pénétration est inversement proportionnelle à la pénétration et dépend du module d'élasticité et des
propriétés viscoélastiques du matériau. La forme du pénétreur, la force qui lui est appliquée et sa durée d'application
influent sur les résultats obtenus, de sorte qu'il ne peut exister de relation simple entre les résultats obtenus avec un
type de duromètre et ceux qui sont obtenus soit avec un autre type de duromètre, soit avec un autre instrument pour
mesurer la dureté.
4 Appareillage
Utiliser un duromètre soit du type Shore A, soit du type Shore D, comprenant les éléments suivants:
4.1 Pied-presseur, percé d'un trou de diamètre 3mm± 0,5 mmcentré à au moins 6 mm des bord
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.