iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 15494:2003

(Main)

Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system - Metric series (ISO 15494:2003)

Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system - Metric series (ISO 15494:2003)

ISO 15494:2003 specifies the characteristics and requirements for components such as pipes, fittings and valves made from one of the following materials:
polybutene (PB);
polyethylene (PE);
polypropylene (PP);
intended to be used for thermoplastics piping systems in above-ground industrial applications.

Kunststoff-Rohrleitungssysteme für industrielle Anwendungen - Polybuten (PB), Polyethylen (PE) und Polypropylen (PP) - Anforderungen an Rohrleitungsteile und das Rohrleitungssystem - Metrische Reihen (ISO 15494:2003)

Diese Internationale Norm legt Eigenschaften und Anforderungen an Rohrleitungsteile wie Rohre, Formstücke und Armaturen aus einem der folgenden Werkstoffe:
¾ Polybuten (PB);
¾ Polyethylen (PE);
¾ Polypropylen (PP)
fest, die für oberirdisch verlegte Industrierohrleitungen aus thermoplastischen Kunststoffen eingesetzt werden.
Diese Norm gilt für Rohre, Formstücke, Armaturen und Zubehörteile aus PB, PE oder PP, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Kunststoffen und Werkstoffen, die abhängig von ihrer Eignung für den Transport von flüssigen und gasförmigen Fluiden sowie von festen Bestandteilen in Fluiden, u.a. für die folgenden Anwendungen vorgesehen sind:
¾ chemische Industrieanlagen;
¾ Industrieabwassertechnik;
¾ Energietechnik (Kühl- und Brauchwasser);
¾ Galvanisierungs- und Beizanlagen;
¾ Halbleiterindustrie;
¾ Futtermittelindustrie;
¾ Kläranlagen.
ANMERKUNG 1     Sofern zutreffend, gelten für besondere Anwendungen (z. B. Kläranlagen) nationale Vorschriften.
Andere Anwendungen als die oben aufgeführten sind zulässig, wenn die Anforderungen dieser Norm und/oder betreffende nationale Anforderungen erfüllt werden.
Entsprechende Vorschriften über das Brandverhalten und mögliche Explosionsgefahren gelten beim Einsatz von leicht entflammbaren Fluiden.
Die Rohrleitungsteile müssen den zu erwartenden mechanischen, thermischen und chemischen Anforderungen widerstehen und gegenüber den transportierten Fluiden beständig sein.
Eigenschaften und Anforderungen, die für alle Werkstoffe (PB, PE und PP) gelten, sind in den entsprechenden Abschnitten dieser Norm aufgeführt. Werkstoffspezifische Eigenschaften und Anforderungen sind für jeden dieser Werkstoffe in einem Anhang (siehe Tabelle 1) festgelegt.
Tabelle 1 - Werkstoffspezifische Anhänge
Werkstoff   Anhang
   Polybuten (PB)   A
   Polyethylen (PE)   B
   Polypropylen (PP)   C
ANMERKUNG 2   Rohrleitungsteile, die einer der in den Literaturhinweisen aufgeführten Produktnormen oder be

Systèmes de canalisations en matières plastiques pour les applications industrielles - Polybutène (PB), polyéthylène (PE) et polypropylène (PP) - Spécifications pour les composants et le système - Série métrique (ISO 15494:2003)

L'ISO 15494:2003 spécifie les caractéristiques et exigences des composants, tels que les tubes, les raccords et les robinets fabriqués à partir d'une des matières suivantes: polybutène (PB), polyéthylène (PE) et polypropylène (PP), destinés à être utilisés dans les systèmes de canalisations thermoplastiques pour des applications industrielles aériennes.

Cevni sistemi iz polimernih materialov za uporabo v industriji - Polibuten (PB, polietilen (PE) in polipropilen (PP) - Zahteve za dele cevovoda in cevni sistem - Metrične serije (ISO 15494 : 2003)

General Information

Status
Withdrawn
Publication Date
14-Apr-2003
Withdrawal Date
03-Nov-2015
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 23 - Thermoplastics systems for industrial applications
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
04-Nov-2015
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN ISO 15494:2003 - Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system - Metric series (ISO 15494:2003)

Relations

Replaced By
EN ISO 15494:2015 - Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) - Metric series for specifications for components and the system (ISO 15494:2015)
Effective Date
11-Nov-2015

Buy Standard

EN ISO 15494:2003EN ISO 15494:2003
PreviousNext
Standard
EN ISO 15494:2003
English language
93 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15494:2003
01-oktober-2003
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DXSRUDERYLQGXVWULML3ROLEXWHQ 3%
SROLHWLOHQ 3( LQSROLSURSLOHQ 33 =DKWHYH]DGHOHFHYRYRGDLQFHYQLVLVWHP
0HWULþQHVHULMH ,62
Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE)
and polypropylene (PP) - Specifications for components and the system - Metric series
(ISO 15494:2003)
Kunststoff-Rohrleitungssysteme für industrielle Anwendungen - Polybuten (PB),
Polyethylen (PE) und Polypropylen (PP) - Anforderungen an Rohrleitungsteile und das
Rohrleitungssystem - Metrische Reihen (ISO 15494:2003)
Systemes de canalisations en matieres plastiques pour les applications industrielles -
Polybutene (PB), polyéthylene (PE) et polypropylene (PP) - Spécifications pour les
composants et le systeme - Série métrique (ISO 15494:2003)
Ta slovenski standard je istoveten z: EN ISO 15494:2003
ICS:
23.040.01
SIST EN ISO 15494:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 15494
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2003
ICS 23.040.01
English version
Plastics piping systems for industrial applications - Polybutene
(PB), polyethylene (PE) and polypropylene (PP) - Specifications
for components and the system - Metric series (ISO
15494:2003)
Systèmes de canalisations en matières plastiques pour les Kunststoff-Rohrleitungssysteme für industrielle
applications industrielles - Polybutène (PB), polyéthylène Anwendungen - Polybuten (PB), Polyethylen (PE) und
(PE) et polypropylène (PP) - Spécifications pour les Polypropylen (PP) - Anforderungen an Rohrleitungsteile
composants et le système - Série métrique (ISO und das Rohrleitungssystem - Metrische Reihen (ISO
15494:2003) 15494:2003)
This European Standard was approved by CEN on 11 March 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15494:2003 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 15494:2003 (E)
CORRECTED  2003-07-02
Foreword
This document (EN ISO 15494:2003) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 "Plastics piping systems and ducting systems", the secretariat of which
is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by October 2003, and conflicting national
standards shall be withdrawn at the latest by October 2003.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 15494:2003 has been approved by CEN as EN ISO 15494:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2

---------------------- Page: 3 ----------------------

EN ISO 15494:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 1566-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1566-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulations, products, joints and assemblies in accordance with the applicable part of EN 1566 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1566 1 (see European foreword), this document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC C) intended to be used for or soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1455-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1455-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulation, products, joints and assemblies in accordance with the applicable part of EN 1455 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1455-1 (see European foreword), this document is applicable to solid wall piping systems made of acrylonitrile-butadiene-styrene (ABS) intended to be used for soil and waste discharge (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1401-1:2019+A1:2023(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1455-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1455-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1566-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1566-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is applicable to PVC-C pipes and fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17152-3:2022(Main)
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Conformity assessment scheme
SIST-TS CEN/TS 17152-3:2023

This document gives guidance for requirements for the assessment of conformity (AoC) of materials, compounds, formulations, products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   Annex B, Table B.1 contains a summary of tests for TT and surveillance monitoring.
In conjunction with EN 17152 1 (see European foreword) this document is applicable to boxes used for infiltration, attenuation and storage systems.

  • Technical specification
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15874-1:2013/A1:2022(Amendment)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1: Impact test (ISO 15874-1:2013/Amd 1:2022)
SIST EN ISO 15874-1:2013/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11295:2022(Main)
Plastics piping systems used for the rehabilitation of pipelines - Classification and overview of strategic, tactical and operational activities (ISO 11295:2022)
SIST EN ISO 11295:2022

This document specifies the steps of the overall process of pipeline rehabilitation, comprising:
—    information on strategic and tactical activities:
a) investigation and condition assessment of the existing pipeline;
b) pipeline rehabilitation planning.
—    information on and requirements for operational activities:
c) project specification;
d) applications of techniques;
e) documentation of the design and application process.
Definitions and classification of families of renovation and trenchless replacement techniques are provided, and their respective features described. Areas of application covered include underground drainage and sewerage networks and underground water and gas supply networks.
The following aspects are not covered by the scope of this document:
—    new construction provided as network extensions;
—    calculation methods to determine, for each viable technique, the characteristics of lining or replacement pipe material needed to secure the desired performance of the rehabilitated pipeline;
—    techniques providing non-structural pressure pipe liners;
—    techniques for local repair.
It is the responsibility of the designer to choose and design the renovation or trenchless replacement pipeline system.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1555-7:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
SIST-TS CEN/TS 1555-7:2022

This document gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
This document gives recommendations that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001.
NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065, EN IS0/IEC 17021 or EN ISO/IEC 17020, as applicable.
In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this document is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar;
b) an operating temperature of 20 °C as reference temperature.
NOTE 2 For other operating temperatures, derating coefficients can be used; see EN 1555-5.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15877-3:2009/A2:2021(Amendment)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 2 (ISO 15877-3:2009/Amd 2:2021)
SIST EN ISO 15877-3:2009/A2:2021
  • Amendment
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day