EN ISO 8469:2006
(Main)Small craft - Non-fire-resistant fuel hoses (ISO 8469:2006)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2006)
ISO 8469:2006 specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol end diesel oil designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m.
ISO 8469:2006 applies to hoses for small craft with permanently installed fuel systems.
Specifications for fire-resistant hoses are laid down in ISO 7840.
Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige Kraftstoffschläuche (ISO 8469:2006)
Diese Internationale Norm legt die allgemeinen Anforderungen und physikalischen Prüfungen für nicht feuerwiderstandsfähige Schläuche fest, die als Benzin- und Dieselleitungen eingesetzt werden. Die Schläuche mit Innendurchmesser bis einschließlich 10 mm sind für Betriebsüberdrücke bis maximal 0,34 MPa ausgelegt, Schläuche mit größerem Innendurchmesser für Betriebsüberdrücke bis maximal 0,25 MPa, in kleinen Wasserfahrzeugen bis 24 m Rumpflänge.
Sie gilt für Schläuche auf kleinen Wasserfahrzeugen, mit fest eingebauten Kraftstoffsystemen.
Spezifikationen für feuerwiderstandsfähige Schläuche sind in ISO 7840 festgelegt.
Petits navires - Tuyaux souples non résistants au feu, pour carburant (ISO 8469:2006)
L'ISO 8469:2006 prescrit les exigences générales et les essais physiques relatifs aux tuyaux souples non résistants au feu pour le transport d'essence ou de gazole, conçus pour une pression de service n'excédant pas 0,34 MPa pour les tuyaux de diamètre intérieur inférieur ou égal à 10 mm, et 0,25 MPa pour les tuyaux de diamètre intérieur allant jusqu'à 63 mm sur les bateaux dont la coque ne dépasse pas 24 m de longueur.
Elle est applicable aux tuyaux destinés aux petits navires à installation à carburant à demeure.
Les spécifications applicables aux tuyaux souples résistant au feu sont fixées dans l'ISO 7840.
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2007
1DGRPHãþD
SIST EN ISO 8469:2000
SIST EN ISO 8469:2000/A1:2001
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2006)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2006)
Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige Kraftstoffschläuche (ISO
8469:2006)
Petits navires - Tuyaux souples non résistants au feu, pour carburant (ISO 8469:2006)
Ta slovenski standard je istoveten z: EN ISO 8469:2006
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
47.020.30 Sistemi cevi Piping systems
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 8469
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2006
ICS 47.080 Supersedes EN ISO 8469:1995
English Version
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2006)
Petits navires - Tuyaux souples non résistants au feu, pour Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige
carburant (ISO 8469:2006) Kraftstoffschläuche (ISO 8469:2006)
This European Standard was approved by CEN on 26 June 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8469:2006: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 8469:2006) has been prepared by Technical Committee ISO/TC 188
"Small craft".in collaboration with Technical Committee CEN/SS T01 "Shipbuilding and maritime
structures", the secretariat of which is held by CMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2007, and conflicting national standards
shall be withdrawn at the latest by January 2007.
This document supersedes EN ISO 8469:1995.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 8469:2006 has been approved by CEN as EN ISO 8469:2006 without any
modifications.
ANNEX ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide one means of conforming to
Essential Requirements of the New Approach Directive 94/25/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive
and has been implemented as a national standard in at least one Member State, compliance with
the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 94/25/EC
Clause(s)/sub-clause(s) Essential requirements (ERs) of EU Qualifying
of this European Directive 94/25/EC remarks/Notes
Standard
All clauses Annex I, Clause 5.1.1, Inboard Engine
Annex I, Clause 5.2.1, Fuel system, General
Annex I, Clause 5.6.1, Fire protection, General
Annex II, Components, 4
WARNING: Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 8469
Second edition
2006-07-01
Small craft — Non-fire-resistant fuel
hoses
Petits navires — Tuyaux souples non résistants au feu, pour carburant
Reference number
ISO 8469:2006(E)
©
ISO 2006
ISO 8469:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 8469:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8469 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 8469:1994), which has been technically revised.
INTERNATIONAL STANDARD ISO 8469:2006(E)
Small craft — Non-fire-resistant fuel hoses
1 Scope
This International Standard specifies general requirements and physical tests for non-fire-resistant hoses for
conveying petrol and diesel oil designed for a working pressure not exceeding 0,34 MPa for hoses with inner
diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length
up to 24 m.
It applies to hoses for small craft with permanently installed fuel systems.
Specifications for fire-resistant hoses are laid down in ISO 7840.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3:1973, Preferred numbers — Series of preferred numbers
1)
ISO 1307:— , Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and
tolerances on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817:2005, Rubber, vulcanized — Determination of the effect of liquids
ISO 7233:2006, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum
ISO 7326:1991, Rubber and plastics hoses — Assessment of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.