EN 14399-5:2005
(Main)High-strength structural bolting assemblies for preloading - Part 5: Plain washers
High-strength structural bolting assemblies for preloading - Part 5: Plain washers
This part of this European Standard specifies, together with prEN 14399-1, hardened and tempered plain washers intended for assembly with large series hexagon high-strength structural bolts and nuts with threads from M12 to M36 inclusive. Washers according to this standard can be applied under the nut only.
NOTE Attention is drawn to the importance of ensuring that the washers are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to ENV 1090-1 is made.
Hochfeste planmäßig vorspannbare Schraubenverbindungen für den Metallbau - Teil 5: Flache Scheiben
Dieser Teil der europäischen Norm beschreibt, zusammen mit prEN 14399-1, vergütete flache Scheiben, welche für die Verwendung mit hochfesten Sechskantschrauben und -muttern mit großer Schlüsselweite für den Metallbau mit Gewindegrößen von M12 bis M36, vorgesehen sind. Scheiben nach dieser Norm können nur unter der Mutter verwendet werden.
ANMERKUNG Damit zufriedenstellende Ergebnisse erreicht werden können, ist auf die korrekte Anwendung der Scheiben besondere Aufmerksamkeit zu richten. Für Empfehlungen zur korrekten Anwendung wird auf ENV 1090-1 hingewiesen.
Boulonnerie de construction métallique à haute résistance apte à la précontrainte - Partie 5 : Rondelles plates
La présente partie de cette Norme européenne, avec le prEN 14399-1, spécifie les exigences applicables aux rondelles plates trempées et revenues destinées à être assemblées avec des vis et écrous hexagonaux de construction à haute résistance à surplat de série large et de diamètre de filetage de M12 et M36 inclus. Les rondelles conformes à cette présente norme ne peuvent être placées que sous l'écrou.
NOTE Il est important de s'assurer que les rondelles soient utilisées de façon correcte afin d'obtenir un résultat satisfaisant. Pour les recommandations relatives à la bonne utilisation, se référer à l'ENV 1090-1.
Visokotrdnostne strukturne vijačne zveze za prednapetje - 5. del: Ploščate podložke
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SRGORåNHHochfeste planmäßig vorspannbare Schraubenverbindungen für den Metallbau - Teil 5: Flache ScheibenBoulonnerie de construction métallique a haute résistance apte a la précontrainte - Partie 5 : Rondelles platesHigh-strength structural bolting assemblies for preloading - Part 5: Plain washers21.060.30Podložke, varovalni elementiWashers, locking elementsICS:Ta slovenski standard je istoveten z:EN 14399-5:2005SIST EN 14399-5:2005en01-maj-2005SIST EN 14399-5:2005SLOVENSKI
STANDARD
SIST EN 14399-5:2005
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14399-5March 2005ICS 21.060.30English versionHigh-strength structural bolting assemblies for preloading - Part5: Plain washersBoulonnerie de construction métallique à haute résistanceapte à la précontrainte - Partie 5 : Rondelles platesHochfeste planmäßig vorspannbareSchraubenverbindungen für den Metallbau - Teil 5: FlacheScheibenThis European Standard was approved by CEN on 30 April 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14399-5:2005: ESIST EN 14399-5:2005
EN 14399-5:2005 (E) 2 Contents page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Dimensions.6 4 Specifications and reference standards.7 5 Designation.7 6 Marking.7 Bibliography.8
SIST EN 14399-5:2005
EN 14399-5:2005 (E) 3 Foreword This document (EN 14399-5:2005) has been prepared by Technical Committee CEN /TC 185, "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the latest by September 2005. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 14399-5:2005
EN 14399-5:2005 (E) 4 Introduction This
document on structural bolting reflects the situation in Europe where two technical solutions exist t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.