EN 10222-4:1998/A1:2001

Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (TC Res C 1/2000) (CC/000331)
2013: Originator of XML version: first setup pilot of CCMC in 2012

Schmiedestücke aus Stahl für Druckbehälter - Teil 4: Schweißgeeignete Feinkornbaustähle mit hoher Dehngrenze

Pièces forgées en acier pour appareils à pression - Partie 4: Aciers soudables à grains fins avec limite d'élasticité élevée

Jekleni izkovki za tlačne posode - 4. del: Variva drobnozrnata jekla z veliko dogovorno napetostjo tečenja

General Information

• Status: Withdrawn
• Publication Date: 24-Jul-2001
• Withdrawal Date: 11-Apr-2017
• ICS: 77.140.30 - Steels for pressure purposes
• ICS: 77.140.85 - Iron and steel forgings
• Technical Committee: ECISS/TC 111 - Steel castings and forgings
• Drafting Committee: ECISS/TC 28 - Steel forgings
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 12-Apr-2017
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 10222-4:2000/A1:2002 - Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength

Relations

• Replaced By: EN 10222-4:2017 - Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
• Effective Date: 19-Apr-2017
• Amends: EN 10222-4:1998 - Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 10222-4:2000/A1:2002
01-september-2002
-HNOHQLL]NRYNL]DWODþQHSRVRGHGHO9DULYDGUREQR]UQDWDMHNOD]YHOLNR
GRJRYRUQRQDSHWRVWMRWHþHQMD
Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof
strength
Schmiedestücke aus Stahl für Druckbehälter - Teil 4: Schweißgeeignete
Feinkornbaustähle mit hoher Dehngrenze
Pieces forgées en acier pour appareils a pression - Partie 4: Aciers soudables a grains
fins avec limite d'élasticité élevée
Ta slovenski standard je istoveten z: EN 10222-4:1998/A1:2001
ICS:
77.140.30
77.140.85
SIST EN 10222-4:2000/A1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 10222-4:1998/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2001
ICS 77.140.30; 77.140.85
English version
Steel forgings for pressure purposes - Part 4: Weldable fine
grain steels with high proof strength
Pièces forgées en acier pour appareils à pression - Partie Schmiedestücke aus Stahl für Druckbehälter - Teil 4:
4: Aciers soudables à grains fins avec limite d'élasticité Schweißgeeignete Feinkornbaustähle mit hoher
élevée Dehngrenze
This amendment A1 modifies the European Standard EN 10222-4:1998; it was approved by CEN on 20 April 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10222-4:1998/A1:2001 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 10222-4:1998/A1:2001 (E)
Foreword
This Amendment EN 10222-4:1998/A1:2001 to the EN 10222-4:1998 has been prepared by Technical Committee ECISS/TC
28 "Steel forgings", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by
endorsement, at the latest by January 2002, and conflicting national standards shall be withdrawn at the latest by January 2002.
This Amendment to the European Standard EN 10222-4:1998 has been prepared under a mandate given to CEN by the
European Commission and the European Free Trade Association, and supports essential requir
...