iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13100-2:2019

(Main)

Non-destructive testing of welded joints in thermoplastics semi- finished products - Part 2: X-ray radiographic testing

Non-destructive testing of welded joints in thermoplastics semi- finished products - Part 2: X-ray radiographic testing

This document specifies fundamental radiographic techniques with film, which enable repeatable results to be obtained economically.
This document applies to the X-ray radiographic examination of heated tool, electrofusion, extrusion and hot gas joints in plastics materials.
It applies to joints in solid wall pipes and plates with a range of thicknesses from 5 mm to 100 mm. It only applies to pipes containing air or other gases at the time of X-ray testing.
This document does not specify acceptance levels of the indications.

Zerstörungsfreie Prüfung von Schweißverbindungen thermoplastischer Kunststoffe - Teil 2: Röntgenprüfung

Dieses Dokument legt die grundlegenden Regeln für Röntgendurchstrahlungstechniken mit Film mit dem Ziel fest, reproduzierbare Ergebnisse in wirtschaftlicher Weise zu erreichen.
Dieses Dokument gilt für die Röntgendurchstrahlungsprüfung von Heizelement , Heizwendel , Extrusions- und Warmgasverbindungen an Kunststoffmaterialien.
Es gilt für Verbindungen an Vollwandrohren und Platten im Dickebereich von 5 mm bis 100 mm. Es ist nur anwendbar für Rohre, die während der Röntgendurchstrahlungsprüfung Luft oder andere Gase enthalten.
Dieses Dokument legt keine Zulässigkeitsgrenzen für die Angaben fest.

Essais non destructifs des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 2: Contrôle radiographique par rayons X

Le présent document spécifie les techniques radiographiques fondamentales avec film qui permettent d’obtenir des résultats reproductibles de manière économique.
Le présent document s’applique au contrôle par radiographie aux rayons X d’assemblages de matières plastiques réalisés par soudage par élément chauffant, par électrofusion, par extrusion et au gaz chaud.
Il s’applique aux assemblages de tubes à paroi compacte et de plaques avec une épaisseur se situant dans la plage allant de 5 mm à 100 mm. Il s’applique uniquement aux tubes contenant de l’air ou un autre gaz au moment du contrôle aux rayons X.
Le présent document ne spécifie aucun niveau d’acceptation pour les indications.

Neporušitveno preskušanje zvarjenih spojev plastomernih polizdelkov - 2. del: Rentgensko (radiografsko) preskušanje

Ta dokument določa temeljne radiografske tehnike, ki omogočajo ekonomičen način pridobivanja ponovljivih rezultatov.
Ta dokument se uporablja za rentgensko radiografsko preiskavo spojev v plastičnih materialih, izdelanih z ogrevanim orodjem, elektrofuzijo, ekstrudiranjem in varjenjem z vročim zrakom.
Uporablja se za spoje v enojnih stenskih ceveh in ploščah z razponom debelin od 5 mm do 100 mm. Uporablja se samo za cevi, ki v času rentgenskega preskušanja vsebujejo zrak ali druge pline.
Dokument ne določa ravni sprejemanja navedb.

General Information

Status
Published
Publication Date
03-Sep-2019
Withdrawal Date
30-Mar-2020
ICS
25.160.40 - Welded joints and welds
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249/WG 16 - Welding of thermoplastics
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
04-Sep-2019
Due Date
16-Apr-2020
Completion Date
04-Sep-2019
Ref Project
SIST EN 13100-2:2019 - Non-destructive testing of welded joints in thermoplastics semi-finished products - Part 2: X-ray radiographic testing

Relations

Replaces
EN 13100-2:2004 - Non-destructive testing of welded joints in thermoplastics semi-finished products - Part 2: X-ray radiographic testing
Effective Date
08-Nov-2017

Buy Standard

EN 13100-2:2019EN 13100-2:2019
PreviousNext
Standard
EN 13100-2:2019
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13100-2:2019
01-november-2019
Nadomešča:
SIST EN 13100-2:2005
Neporušitveno preskušanje zvarjenih spojev plastomernih polizdelkov - 2. del:
Rentgensko (radiografsko) preskušanje
Non-destructive testing of welded joints in thermoplastics semi-finished products - Part 2:
X-ray radiographic testing
Zerstörungsfreie Prüfung von Schweißverbindungen thermoplastischer Kunststoffe - Teil
2: Röntgenprüfung
Essais non destructifs des assemblages soudés sur produits semi-finis en
thermoplastiques - Partie 2: Contrôle radiographique par rayons X
Ta slovenski standard je istoveten z: EN 13100-2:2019
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
83.140.01 Izdelki iz gume in polimernih Rubber and plastics products
materialov na splošno in general
SIST EN 13100-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13100-2:2019

---------------------- Page: 2 ----------------------
SIST EN 13100-2:2019


EN 13100-2
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2019
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN 13100-2:2004
English Version

Non-destructive testing of welded joints in thermoplastics
semi- finished products - Part 2: X-ray radiographic testing
Essais non destructifs des assemblages soudés sur Zerstörungsfreie Prüfung von Schweißverbindungen
produits semi-finis en thermoplastiques - Partie 2: thermoplastischer Kunststoffe - Teil 2:
Contrôle radiographique par rayons X Röntgenprüfung
This European Standard was approved by CEN on 21 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13100-2:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13100-2:2019
EN 13100-2:2019 (E)
Contents Page
European foreword . 3
1 Scope. 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols and abbreviations . 5
5 General . 6
5.1 Security measures . 6
5.2 Surface preparation and stage of manufacture . 6
5.3 Location of the weld in the radiograph . 6
5.4 Identification of radiographs .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12814-7:2024(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 7: Tensile test with waisted test specimens
kSIST FprEN 12814-7:2023

This document specifies the dimensions, the method of sampling, the preparation of the test specimens and the conditions for performing the tensile test with waisted test specimens in order to determine the tensile energy welding factor.
A tensile test with waisted specimens can be used in conjunction with other tests (e.g. bend, tensile, tensile creep, macro, etc.) to assess the performance of welded assemblies, made from thermoplastics materials.
The test is applicable to co-axial or co-planar heated tool butt welded assemblies made from thermoplastics materials filled or unfilled, but not reinforced. It is not applicable to tubular assemblies with a nominal outside diameter less than 90 mm.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16296:2021(Main)
Imperfections in thermoplastics welded joints - Quality levels
SIST EN 16296:2021

This document specifies quality levels for imperfections in thermoplastics welded joints that have cooled to ambient temperature and is applicable to material thickness above 2,0 mm.
Three quality levels are specified in order to permit application for a wide range of welded fabrication. They are designated by symbols B, C and D, where B is the most stringent. The quality levels refer to production quality and not to the fitness-for-purpose (see 3.2) of the manufactured product.
The quality level necessary are expected to be defined by the application standard or by the fabricator in conjunction with the user and/or other parties concerned. The level is expected to be prescribed before the start of production, preferably at the enquiry or order stage.
This document applies to the following thermoplastic materials in Table 1:
and to the following welding processes:
-   heated tool welding;
-   electrofusion socket welding;
-   hot gas welding using filler rod only;
-   extrusion welding;
-   solvent welding of pipes.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12814-2:2021(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test
SIST EN 12814-2:2021

This document specifies the dimensions, the method of sampling, the preparation of the test specimens and the conditions for performing the tensile test in order to determine the short-term tensile welding factor.
A tensile test can be used in conjunction with other tests (e.g. bend, tensile creep, macro) to assess the performance of welded assemblies, made from thermoplastics materials.
The test is applicable to welded semi-finished products made from thermoplastics materials filled or unfilled, but not reinforced, irrespective of the welding process used.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12814-8:2021(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
SIST EN 12814-8:2021

This document provides the requirements for the tests made on welded thermoplastics semi-finished products.
The selection of the appropriate test method(s) is made in accordance with the particular type and application of welded product.
The test results depend on the conditions of manufacture for the test specimen and on the test conditions. They can therefore only be related to the behaviour of the product or can only be used for designing a structure, if the test conditions can be related to the service conditions.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14728:2019(Main)
Imperfections in thermoplastic welds - Classification
SIST EN 14728:2019

This document specifies a system for classifying imperfections that may be encountered in thermoplastic welded joints during manufacture and provides examples of imperfections for the following welding processes:
-   heated tool butt welding;
-   heated tool socket welding;
-   electrofusion socket welding;
-   hot gas welding;
-   extrusion welding;
-   solvent socket welding.
This document does not describe imperfections that may be generated during service or imperfections present before welding, which are due to poor preparation or assembly of components (e.g. fit up). The correct preparation and assembly of components (e.g. fit up) are described in the relevant welding procedure specification (WPS).
This document is also not concerned with the search for the possible influence of these imperfections on the behaviour of joints in relation to the different types of stress to which the latter may be subjected or on methods for preventing such imperfections.
This document can be used in conjunction with EN 16296 [1] to determine the acceptance of welds.
Only imperfections giving rise to discontinuities of materials or changes in shape are taken into consideration in this document, specifying their type, their shape and their positions. This classification can be used to determine the possible origin or causes of the imperfections.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12814-4:2018/AC:2018(Corrigendum)
Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test
SIST EN 12814-4:2018/AC:2018

This document specifies the dimensions, the method of sampling and the preparation of the test specimens, and also the conditions for performing the peel test perpendicular to the weld in order to determine the peel resistance and the failure behaviour.
A peel test can be used in conjunction with other tests (e.g. tensile creep, macroscopic examination...) to assess the performance of welded assemblies, made from thermoplastics materials.
Peel tests are applicable to overlap welded assemblies made from thermoplastics materials.
The T-peel test as defined in Clause 5 will be used only for assessing welded sheet assemblies. This test is not applicable to welded test pieces containing sheets of different nominal thickness.
The decohesion test as defined in Clause 6 will be used only for assessing electrofusion joints with nominal thickness of pipe/fitting greater than 10 mm.
For socket fusion and for electrofusion socket joints with nominal outside diameter less than or equal to 90 mm, a crush test will be used, as defined in Clause 7.
The crush test can also be used for electrofusion joints with outside diameters greater than 90 mm.
The crush test for electrofusion saddle joints will be performed in accordance with ISO 13955 [1].
NOTE   A decohesion test is also defined in ISO 13954 [2].
The tests defined in this standard are not intended to be used for assessment and/or qualification of thermoplastic fittings that already have their own requirements, e.g. polyethylene fittings according to EN 1555-3 [3] and EN 12201-3 [4].

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12814-4:2018(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test
SIST EN 12814-4:2018

This document specifies the dimensions, the method of sampling and the preparation of the test specimens, and also the conditions for performing the peel test perpendicular to the weld in order to determine the peel resistance and the failure behaviour.
A peel test can be used in conjunction with other tests (e.g. tensile creep, macroscopic examination...) to assess the performance of welded assemblies, made from thermoplastics materials.
Peel tests are applicable to overlap welded assemblies made from thermoplastics materials.
The T-peel test as defined in Clause 5 will be used only for assessing welded sheet assemblies. This test is not applicable to welded test pieces containing sheets of different nominal thickness.
The decohesion test as defined in Clause 6 will be used only for assessing electrofusion joints with nominal thickness of pipe/fitting greater than 10 mm.
For socket fusion and for electrofusion socket joints with nominal outside diameter less than or equal to 90 mm, a crush test will be used, as defined in Clause 7.
The crush test can also be used for electrofusion joints with outside diameters greater than 90 mm.
The crush test for electrofusion saddle joints will be performed in accordance with ISO 13955 [1].
NOTE   A decohesion test is also defined in ISO 13954 [2].
The tests defined in this standard are not intended to be used for assessment and/or qualification of thermoplastic fittings that already have their own requirements, e.g. polyethylene fittings according to EN 1555-3 [3] and EN 12201-3 [4].

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13100-1:2017(Main)
Non destructive testing of welded joints of thermoplastics semi-finished products - Part 1: Visual examination
SIST EN 13100-1:2017

This European standard covers the visual examination of welds in thermoplastic materials. It may also be applied to visual testing of the joint prior to and during the welding.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12814-3:2014(Main)
Testing of welded joints in thermoplastics semi-finished products - Part 3: Tensile creep test
SIST EN 12814-3:2014

This European Standard specifies the dimensions, the method of sampling and the preparation of the test specimens, and the conditions for performing the tensile creep test perpendicular to the weld in order to determine the long-term tensile welding factor.
A tensile creep test may be used in conjunction with other tests (e.g. bend test, tensile test, macrographic examination,...) to assess the performance of welded assemblies, made from thermoplastics materials.
The test is applicable to welded assemblies made from thermoplastics materials filled or unfilled such as tubes and fittings, sheets, plates and profiles, but not reinforced, irrespective of the welding process used.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13100-4:2012(Main)
Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing
SIST EN 13100-4:2014

This European Standard specifies the equipment and methods for the high voltage testing of butt or overlap welded joints in thermoplastic sheets for locating through-thickness defects only. It applies to new unused constructions only.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day