EN ISO 1518-2:2019

Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading method (ISO 1518-2:2019)

This document specifies a method for determining, using a pointed stylus loaded with a continuously increasing load, the scratch resistance of a single coating of a paint, varnish or related product, or the upper layer of a multicoat system.
This test has been found to be useful in comparing the scratch resistance of different coatings. It is most useful in providing relative ratings for a series of coated panels exhibiting significant differences in scratch resistance.
NOTE       Neither this document nor ISO 1518‑1 specifies a method using a curved stylus, which is specified in ISO 12137. The choice between the three methods will depend on the particular practical problem.

Beschichtungsstoffe - Bestimmung der Kratzbeständigkeit - Teil 2: Verfahren mit kontinuierlich ansteigender Last (ISO 1518-2:2019)

Dieses Dokument legt ein Verfahren zum Bestimmen der Widerstandsfähigkeit einer einzelnen Schicht aus einem Beschichtungsstoff oder der obersten Schicht eines Mehrschichtsystems gegen Kratzer fest, bei dem ein spitzer Stichel mit einer kontinuierlich ansteigenden Last verwendet wird.
Diese Prüfung wurde zum Vergleich der Kratzbeständigkeit unterschiedlicher Beschichtungen als nützlich befunden. Sie ist besonders geeignet, wenn bei einer Reihe beschichteter Probenplatten mit deutlich unter¬schiedlicher Kratzbeständigkeit relative Einstufungen erhalten werden sollen.
ANMERKUNG   Weder dieses Dokument noch ISO 1518 1 legen ein Verfahren mit einem gebogenen Stichel fest, das in ISO 12137 festgelegt ist. Welches der drei Verfahren gewählt wird, hängt von der jeweiligen Fragestellung ab.

Peintures et vernis - Détermination de la résistance à la rayure - Partie 2: Méthode à charge variable (ISO 1518-2:2019)

Le présent document spécifie une méthode pour la détermination, à l'aide d'un stylet pointu auquel une charge augmentant de manière continue est appliquée, de la résistance à la rayure d'une couche unique de peinture, de vernis ou de produit assimilé, ou de la couche supérieure d'un système multicouche.
Cet essai s'est avéré utile pour comparer la résistance à la rayure de différents revêtements. Il permet notamment de fournir des valeurs comparatives pour une série de panneaux revêtus présentant des différences significatives de résistance à la rayure.
NOTE       Ni le présent document ni l'ISO 1518-1 ne spécifient de méthode utilisant un stylet arrondi, celle-ci étant spécifiée dans l'ISO 12137. Le choix entre les trois méthodes va dépendre du problème pratique particulier.

Barve in laki - Ugotavljanje odpornosti proti razenju - 2. del: Metoda s stopnjevano obremenitvijo (ISO 1518-2:2019)

Ta dokument določa metodo za ugotavljanje odpornosti proti razenju enopokrivnega sistema barve, laka ali sorodnega izdelka ali zgornjega sloja večpokrivnega sistema proti razenju z ostro ošiljenim praskalom s stalnim povečanjem obremenitve.
Ta preskus se je izkazal za uporabnega pri primerjavi odpornosti proti razenju različnih premazov. Predvsem uporaben je za zagotavljanje relativnih vrednosti za serije premazanih plošč, ki se precej razlikujejo v odpornosti proti razenju.
OPOMBA: Niti ta dokument niti standard ISO 1518-1 ne določata metode z uporabo ukrivljenega praskala, ki je določena v standardu ISO 12137. Izbira ene od treh metod je odvisna od posameznega praktičnega problema.

General Information

• Status: Published
• Publication Date: 02-Jul-2019
• Withdrawal Date: 30-Jan-2020
• ICS: 87.040 - Paints and varnishes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 03-Jul-2019
• Completion Date: 03-Jul-2019
• Ref Project: SIST EN ISO 1518-2:2019 - Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading method (ISO 1518-2:2019)

Relations

• Replaces: EN ISO 1518-2:2011 - Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading method (ISO 1518-2:2011)
• Effective Date: 10-Jul-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1518-2:2019
01-september-2019
Nadomešča:
SIST EN ISO 1518-2:2011
Barve in laki - Ugotavljanje odpornosti proti razenju - 2. del: Metoda s stopnjevano
obremenitvijo (ISO 1518-2:2019)
Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading
method (ISO 1518-2:2019)
Beschichtungsstoffe - Bestimmung der Kratzbeständigkeit - Teil 2: Verfahren mit
kontinuierlich ansteigender Last (ISO 1518-2:2019)
Peintures et vernis - Détermination de la résistance à la rayure - Partie 2: Méthode à
charge variable (ISO 1518-2:2019)
Ta slovenski standard je istoveten z: EN ISO 1518-2:2019
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 1518-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1518-2:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 1518-2:2019


EN ISO 1518-2
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2019
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 1518-2:2011
English Version

Paints and varnishes - Determination of scratch resistance
- Part 2: Variable-loading method (ISO 1518-2:2019)
Peintures et vernis - Détermination de la résistance à la Beschichtungsstoffe - Bestimmung der
rayure - Partie 2: Méthode à charge variable (ISO 1518- Kratzbeständigkeit - Teil 2: Verfahren mit
2:2019) kontinuierlich ansteigender Last (ISO 1518-2:2019)
This European Standard was approved by CEN on 30 May 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1518-2:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1518-2:2019
EN ISO 1518-2:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1518-2:2019
EN ISO 1518-2:2019 (E)
European foreword
This document (EN ISO 1518-2:2019) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall
be withdrawn at the latest by January 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1518-2:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 1518-2:2019 has been approved by CEN as EN ISO 1518-2:2019 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 1518-2:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 1518-2:2019
INTERNATIONAL ISO
STANDARD 1518-2
Secon
...