EN ISO 6103:2005

Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Static testing (ISO 6103:2005)

ISO 6103:2005 specifies the maximum permissible values of unbalances for various grinding wheels of ISO 603-1 to ISO 603-9 and ISO 603-12 to ISO 603-16 in the as-delivered condition, with an outside diameter greater than 115 mm and maximum operating speed greater than or equal to 16 m/s. It also specifies the method for measuring the unbalance and the practical method for testing whether a grinding wheel is acceptable or not.
ISO 6103:2005 is applicable to bonded abrasive grinding wheels in the as-delivered condition. It is not applicable to diamond, cubic boron nitride or natural stone grinding wheels, or centreless control wheels, lapping and disc wheels, ball wheels or glass grinding wheels.

Schleifkörper aus gebundenem Schleifmittel - Zulässige Unwucht von Schleifscheiben im Lieferzustand - Statische Prüfung (ISO 6103:2003)

Diese Internationale Norm legt die maximal zulässigen Unwuchten für verschiedene Formen von Schleifscheiben nach ISO 603 1 bis ISO 603 9 und ISO 603 12 bis ISO 603 16 im Lieferzustand fest, mit einem Außendurchmesser von D > 115 mm und einer Arbeitshöchstgeschwindigkeit, vs ³ 16 m/s fest.
Ein Verfahren zum Messen der Unwucht ist ebenfalls festgelegt und ein geeignetes Verfahren, um zu prüfen, ob die Schleifscheibe akzeptabel ist oder nicht.
Diese Internationale Norm ist anwendbar für Schleifscheiben aus gebundenem Schleifmittel im Lieferzustand.
Diese Internationale Norm gilt nicht für
-   Schleifscheiben mit Diamant, kubischem Bornitrid oder Naturstein oder
-   Regelscheiben beim spitzenlosen Schleifen, Läpp Scheiben und Schleifscheiben mit Tragscheiben, Schleifscheiben zum Schleifen von Kugeln oder Glas.
ANMERKUNG 1   Die angegebenen Werte beziehen sich auf die Schleifscheibe selbst, unabhängig von jeder Unwucht, die in der Hilfswelle oder in der Befestigung der Scheibe auf der Hilfswelle auftreten kann. Es wird vorausgesetzt, dass diese Einzelteile zusammen mit den Flanschen oder Aufnahmeflanschen ausgewuchtet wurden und homogen sowie frei von geometrischen Fehlern sind.
ANMERKUNG 2   Die Auswirkungen der Unwucht sind die Ursache für
-   zusätzliche Belastung der Hilfswelle, der Maschine und ihrer Befestigung,
-   außergewöhnliche Abnutzung der Lager,
-   Schwingungen, die das Schleifergebnis beeinflussen, und erhöhte innere Spannungen in der Schleifscheibe und
-   fortschreitende Ermüdung des Bedieners.

Produits abrasifs agglomérés - Balourds admissibles des meules en état de livraison - Contrôle statique (ISO 6103:2005)

L'ISO 6103:2004 spécifie les valeurs maximales admissibles des balourds auxquelles doivent satisfaire, dans les conditions de livraison, les différents types de meules de l'ISO 603-1 à l'ISO 603-9 et de l'ISO 603-12 à l'ISO 603-16, de diamètre extérieur supérieur à 115 mm et de vitesse maximale de fonctionnement supérieure ou égale à 16 m/s. Elle spécifie également la méthode de mesurage du balourd et la méthode pratique pour contrôler si une meule est acceptable ou non.
L'ISO 6103:2004 est applicable aux meules à base d'abrasifs agglomérés dans les conditions de livraison. Elle ne s'applique pas aux meules à base de diamant, de nitrure de bore cubique ou en pierre naturelle, et aux meules d'entraînement sans centre, aux disques et lapidaires de rodage, aux meules à billes et aux meules pour le travail du verre.

Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Static testing (ISO 6103:2005)

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2005
• Withdrawal Date: 14-Oct-2014
• ICS: 25.100.70 - Abrasives
• Technical Committee: CEN/TC 143 - Machine tools - Safety
• Drafting Committee: CEN/TC 143/WG 2 - Stationary grinding machines and abrasive products - Safety
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 15-Oct-2014
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Ref Project: SIST EN ISO 6103:2005 - Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Static testing (ISO 6103:2005)

Relations

• Replaces: EN ISO 6103:1999 - Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Testing (ISO 6103:1999)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 6103:2014 - Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Static testing (ISO 6103:2014)
• Effective Date: 22-Oct-2014

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6103:2005
01-oktober-2005
1DGRPHãþD
SIST EN ISO 6103:2000
Bonded abrasive products - Permissible unbalances of grinding wheels as
delivered - Static testing (ISO 6103:2005)
Bonded abrasive products - Permissible unbalances of grinding wheels as delivered -
Static testing (ISO 6103:2005)
Schleifkörper aus gebundenem Schleifmittel - Zulässige Unwucht von Schleifscheiben im
Lieferzustand - Statische Prüfung (ISO 6103:2003)
Produits abrasifs agglomérés - Balourds admissibles des meules en état de livraison -
Contrôle statique (ISO 6103:2005)
Ta slovenski standard je istoveten z: EN ISO 6103:2005
ICS:
25.100.70 Brusiva Abrasives
SIST EN ISO 6103:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6103:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 6103:2005



EUROPEAN STANDARD
EN ISO 6103

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2005
ICS 25.100.70 Supersedes EN ISO 6103:1999
English version
Bonded abrasive products - Permissible unbalances of grinding
wheels as delivered - Static testing (ISO 6103:2005)
Produits abrasifs agglomérés - Balourds admissibles des
meules en état de livraison - Contrôle statique (ISO
6103:2005)
This European Standard was approved by CEN on 23 March 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6103:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 6103:2005
EN ISO 6103:2005 (E)


Foreword

This document (EN ISO 6103:2005) has been prepared by Technical Committee ISO/TC 29 "Small tools" in
collaboration with Technical Committee CEN/TC 143 "Machine tools - Safety", the secretariat of which is
held by SNV.

This document supersedes EN ISO 6103:1999.

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2005, and conflicting national standards shall be withdrawn
at the latest by October 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.


Endorsement notice

The text of ISO 6103:2005 has been approved by CEN as EN ISO 6103:2005 without any modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 6103:2005

INTERNATIONAL ISO
STANDARD 6103
Third edition
2005-04-01


Bonded abrasive products — Permissible
unbalances of grinding wheels as
delivered — Static testing
Produits abrasifs agglomérés — Balourds admissibles des meules en
état de livraison — Contrôle statique





Reference number
ISO 6103:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 6103:2005
ISO 6103:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used
...