EN ISO 7551:1998
(Main)Dental absorbent points (ISO 7551:1996)
Dental absorbent points (ISO 7551:1996)
Specifies requirements and test methods for dental absorbent points used in endodontic procedures.
Zahnärztliche absorbierende Spitzen (ISO 7551:1996)
In der vorliegenden internationalen Norm werden Anforderungen und Prüfmethoden für absorbierende Spitze, die keine Arzneistoffe enthalten, und die in endodontischen Behandlungsverfahren angewandt werden, festgelegt. Die Anforderungen gelten für absorbierende Spitzen, die durch ein vom Hersteller empfohlenes Sterilisationsverfahren sterilisiert wurden. Zahnärztliche absorbierende Spitzen umfaßen genormte Stifte und kegelförmige Stifte.
Cônes absorbants à usage dentaire (ISO 7551:1996)
La présente Norme internationale fixe les prescriptions et méthodes d'essai relatives aux cônes absorbants pharmaceutiquement inertes, utilisés en endodontie. Les prescriptions s'appliquent aux cônes absorbants ayant été stérilisés une fois, selon une méthode approuvée par le fabricant. Les cônes absorbants dentaires regroupent les cônes absorbants à conicité normalisée et les cônes absorbants à conicité libre. La présente Norme internationale ne fixe pas de prescriptions ou de méthodes d'essai relatives à la stérilité et/ou l'absence de risques biologiques des cônes absorbants dentaires.
Dental absorbent points (ISO 7551:1996)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7551:2000
01-januar-2000
Dental absorbent points (ISO 7551:1996)
Dental absorbent points (ISO 7551:1996)
Zahnärztliche absorbierende Spitzen (ISO 7551:1996)
Cônes absorbants a usage dentaire (ISO 7551:1996)
Ta slovenski standard je istoveten z: EN ISO 7551:1998
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
SIST EN ISO 7551:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7551:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 7551:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 7551:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 7551:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 7551:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 7551:2000
IS0
INTERNATIONAL
7551
STANDARD
First edition
1996-12-15
Dental absorbent points
CGnes absorbants ;i usage dentaire
Reference number
IS0 7551 :I 996(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 7551:2000
IS0 7551:1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 7551 was prepared by Technical Committee
lSO/TC 106, Dentistry, Subcommittee SC 1, Filling and restorative
materials.
Annex A of this International Standard is for information only.
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be
reproduced or utilized in any form or by any means, electronic or mechanical, including
photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 7551:2000
IS0 7551:1996(E)
@ IS0
Introduction
The sizes of the absorbent points specified in this International Standard
have been aligned with the corresponding sizes for obturating points
specified in IS0 6877.
Specific qualitative and quantitative requirements for freedom from
biological hazard are not included in this International Standard, but it is
recommended that in assessing possible or toxicological hazards,
7405.
reference should be made to IS0
Dental absorbent points are used in root-canal therapy to dry root canals or
to carry medicaments into the root canal. They are therefore made of fine-
grade absorbent material with a close texture to give an essentially
smooth lint-free surface. To enable insertion into a prepared root canal, the
absorbent point must have some rigidity, be essentially straight and
circular in cross-section.
---------------------- Page: 9 ----------------------
SIST EN ISO 7551:2000
This page intentionally left blank
---------------------- Page: 10 ----------------------
SIST EN ISO 7551:2000
IS0 7551:1996(E)
INTERNATIONAL STANDARD @ IS0
Dental absorbent points
1 Scope
This International Standard specifies requirements and test methods for nonmedicated absorbent points used in
endodontic procedures.
The requirements apply to absorbent points which have been sterilized once in a manner approved by the
manufacturer. Dental absorbent points include standard points and taper size points.
This International Standard does not specify requirements or test methods for sterility and/or freedom from
biological hazard of dental absorbent points.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain
registers of currently valid International Standards.
IS0 3630-I :I 992, Dental root-canal instr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.