EN 485-2:2004

Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties

This part of EN 485 specifies the mechanical properties of wrought aluminium and aluminium alloy sheet, strip and plate for general engineering applications. It applies to flat rolled products. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, etc., sheets and strips or to special applications such as aerospace, can stock, finstock, etc., which are dealt with in separate EN standards.

Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 2: Mechanische Eigenschaften

Dieser Teil der EN 485 legt die mechanischen Eigenschaften für Bleche, Bänder und Platten aus Aluminium und Aluminium-Knetlegierungen fest, die für allgemeine Verwendung besimmt sind. Er gilt für flachgewalzte Erzeugnisse. Er gilt nicht für Vorwalzbänder, Spezialerzeugnisse wie z.B. rollgeformte, geprägte oder lackierte Bänder und Bleche, oder Erzeugnisse, die für Spezialanwendungen, wie beispielsweise Luft- und Raumfahrt, Getränkedosen, Wärmeaustauscher usw. eingesetzt werden. Diese werden in gesonderten Europäischen Normen abgehandelt.

Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 2: Caractéristiques mécaniques

La présente partie de l'EN 485 spécifie les caractéristiques mécaniques des tôles, bandes et tôles épaisses en aluminium et alliages d'aluminium corroyés pour applications courantes. Elle s'applique aux produits laminés plats. Elle ne s'applique pas aux demi-produits laminés, livrés en bobines, destinés à être relaminés (ébauches pour laminage) ni aux produits spéciaux tels que profils de forme, tôles et bandes gravées, laquées, etc., ni aux produits pour applications spéciales telles que la construction aéronautique, le boîtage, les échangeurs thermiques, etc., qui sont traîtés dans des normes EN séparées.

Aluminij in aluminijeve zlitine - Pločevine, trakovi in plošče - 2. del: Mehanske lastnosti

General Information

• Status: Withdrawn
• Publication Date: 06-Jul-2004
• Withdrawal Date: 03-Apr-2007
• ICS: 77.150.10 - Aluminium products
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 7 - Sheets, strips and plates
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 04-Apr-2007
• Completion Date: 04-Apr-2007
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 87/404/EEC - Simple pressure vessels
• Directive: 89/106/EEC - Construction products
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/120 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural metallic products and ancillaries
• Mandate: M/BC/CEN/89/2 - Standardization mandate to CEN concerning supporting standards in the context of pressure vessels
• Ref Project: SIST EN 485-2:2004 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties

Relations

• Replaces: EN 485-2:1994 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
• Effective Date: 22-Dec-2008
• Replaced By: EN 485-2:2007 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2004
1DGRPHãþD
SIST EN 485-2:1998
$OXPLQLMLQDOXPLQLMHYH]OLWLQH3ORþHYLQHWUDNRYLLQSORãþHGHO0HKDQVNH
ODVWQRVWL
Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 2:
Mechanische Eigenschaften
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 2:
Caractéristiques mécaniques
Ta slovenski standard je istoveten z: EN 485-2:2004
ICS:
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 485-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 77.150.10 Supersedes EN 485-2:1994
English version
Aluminium and aluminium alloys - Sheet, strip and plate - Part 2:
Mechanical properties
Aluminium et alliages d'aluminium - Tôles, bandes et tôles Aluminium und Aluminiumlegierungen - Bänder, Bleche
épaisses - Partie 2: Caractéristiques mécaniques und Platten - Teil 2: Mechanische Eigenschaften
This European Standard was approved by CEN on 24 March 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 485-2:2004: E
worldwide for CEN national Members.

Contents
Foreword.4
1 Scope.6
2 Normative references.6
3 Tensile test.6
4 Bend test.7
5 Hardness test.7
Table 1 — Minimum material gauge and Brinell hardness values .8
6 Electrical conductivity.8
7 Stress-corrosion resistance.8
8 Exfoliation corrosion resistance (5xxx series alloys).9
9 Exfoliation corrosion resistance (7xxx series alloys).9
Table 2 — Aluminium EN AW-1080A [Al 99,8(A)] .12
Table 3 — Aluminium EN AW-1070A [Al 99,7] .13
Table 4 — Aluminium EN AW-1050A [Al 99,5] .14
Table 5 — Aluminium EN AW-1200 [Al 99,0].15
Table 6 — Alloy EN AW-2014 [Al Cu4SiMg] .16
Table 7 — Alloy EN AW-2014A [Al Cu4SiMg(A)].17
Table 8 — Alloy EN AW-2017A [Al Cu4MgSi(A)].18
Table 9 — Alloy EN AW-2024 [Al Cu4Mg1].19
Table 10 — Alloy EN AW-3003 [Al Mn1Cu].20
Table 11 — Alloy EN AW-3103 [Al Mn1].21
Table 12 — Alloy EN AW-3004 [Al Mn1Mg1] .22
Table 13 — Alloy EN AW-3005 [Al Mn1Mg0,5] .23
Table 14 — Alloy EN AW-3105 [Al Mn0,5Mg0,5] .24
Table 15 — Alloy EN AW-4006 [Al Si1Fe] .25
Table 16 — Alloy EN AW-4007 [Al Si1,5Mn] .25
Table 17 — Alloy EN AW-4015 [Al Si2Mn] .26
Table 18 — Alloy EN AW-5005 [Al Mg1(B)], alloy EN AW-5005A [Al Mg1(C)].27
Table 19 — Alloy EN AW-5040 [Al Mg1,5Mn] .28
Table 20 — Alloy EN AW-5049 [Al Mg2Mn0,8] .29
Table 21 — Alloy EN AW-5449 [Al Mg2Mn0,8(B)] .30
Table 22 — Alloy EN AW-5050 [Al Mg1,5(C)] .31
Table 23 — Alloy EN AW-5251 [Al Mg2].32
Table 24 — Alloy EN AW-5052 [Al Mg2,5] .33
Table 25 — Alloy EN AW-5154A [Al Mg3,5(A)].34
Table 26 — Alloy EN AW-5454 [Al Mg3Mn] .35
Table 27 — Alloy EN AW-5754 [Al Mg3] .36
Table 28 — Alloy EN AW-5182 [Al Mg4,5Mn0,4] .37
Table 29 — Alloy EN AW-5083 [Al Mg4,5Mn0,7] .38
Table 30 — Alloy EN AW-5383 [Al Mg4,5Mn0,9] .39
Table 31 — Alloy EN AW-5086 [Al Mg4] .40
Table 32 — Alloy EN AW-6016 [Al Si1,2Mg0,4].41
Table 33 — Alloy EN AW-6061 [Al Mg1SiCu] .41
Table 34 — Alloy EN AW-6082 [Al Si1MgMn].42
Table 35 — Alloy EN AW-7020 [Al Zn4,5Mg1].43
Table 36 — Alloy EN AW-7021 [Al Zn5,5Mg1,5].44
Table 37 — Alloy EN AW-7022 [Al Zn5Mg3Cu] .44
Table 38 — Alloy EN AW-7075 [Al Zn5,5MgCu] .45
Table 38 (concluded).46
Table 39 — Alloy EN AW-8011A [Al FeSi(A)] .47
Annex A (normative) Rules for rounding.48
Bibliography.49
Foreword
This document (EN 485-2:2004) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by January 2005, and conflicting national standards shall be withdrawn at the latest
by January 2005.
Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 "Sheet, strip and
plate" to prepare the following standard:
EN 485-2, Aluminium and aluminium alloys — Sheet, strip and plate — Part 2: Mechanical properties.
This standard is part of a set of four standards. The other standards deal with:
 Part 1: Technical conditions for inspection and delivery
 Part 3: Tolerances on dimensions and form for hot-rolled products
 Part 4: Tolerances on shape and dimensions for cold-rolled products
This document supersedes EN 485-2:1994.
Besides very slight editorial adjustments in the text and update of normative references, the following technical
changes have been made:
Clause 1: NOTE added.
Clause 2: ASTM G34-86 changed into ASTM G34-97
ASTM G66-86 changed into ASTM G66-95
Clause 5: Note added
Tables 2 to 39: Due to the introduction of new alloys, the tables have been renumbered when necessary.
New alloys: EN AW-2014A, 4015, 5005A, 5449, 5383, 6016.
Modified values or extended ranges:
EN AW-1070A: O/H111 (over 12,5 mm up to 25,0 mm) added.
EN AW-1050A: O/H111 (over 12,5 mm up to 80,0 mm) extended.
H14 (over 0,5 mm up to 1,5 mm) A modified.
50 mm
H24 (over 0,5 mm up to 1,5 mm) A modified.
50 mm
EN AW-1200: O/H111 (over 12,5 mm up to 80,0 mm) extended.
EN AW-2014: T6, T651 (over 100,0 mm up to 160,0 mm) extended.
EN AW-2017A: T4, T451 modified, T452 added.
EN AW-3103: H16 (over 4,0 mm up to 8,0 mm) added.
EN AW-5049: H112 (6,0 up to 25,0) modified.
EN AW-5052: F modified, H112 (6,0 mm up to 12,5 mm) modified.
EN AW-5454: F modified and extended.
EN AW-5754: F (over 100,0 mm up to 150,0 mm) added, H112 modified.
EN AW-5083: F modified, O/H111 (over 120,0 mm up to 300,0 mm) extended,
H112 (over 80,0 mm up to 120,0 mm) added.
EN AW-5086: H112 (6,0 mm up to 12,5 mm) modified.
EN AW-6061: T6, T651, T62 (over 150,0 mm up to 400,0 mm) extended.
EN AW-6082: T6, T651, T62 (over 175,0 mm up to 350,0 mm) added.
EN AW-7020: T6, T651, T62 (over 175,0 mm up to 250,0 mm) added.
EN AW-7075: T6, T651, T62 (over 150,0 mm up to 300,0 mm) added, T652 added.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
1 Scope
This part of EN 485 specifies the mechanical properties of wrought aluminium and aluminium alloy sheet, strip and
plate for general engineering applications.
It applies to flat rolled products.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to
special products such as corrugated, embossed, painted, etc. sheets and strips or to special applications such as
aerospace, can stock, finstock, etc. which are dealt with in separate European Standards.
The systems for designating these materials are described in EN 573-1 and EN 573-2. Their chemical composition
limits are specified in EN 573-3.
Mechanical property limits are specified for all Class A alloys, as defined in EN 573-4.
Temper designations are defined in EN 515.
NOTE Some of the products listed in the present standard can be subject to patent or patent applications, and their listing
herein does not in any way imply the granting of a licence under such patent right.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised
standard products u
...