iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 818-2:1996+A1:2008

(Main + Amendment)

Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain slings - Grade 8

Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain slings - Grade 8

This part of EN 818 specifies the requirements related to safety for short link chains, grade 8, of medium tolerance for use in chain slings according to EN 818-4 and for general lifting purposes. They are electrically welded round steel short link chains, heat treated and tested and complying with the general conditions of acceptance in EN 818-1.
The range of nominal sizes of chain covered by this Part of EN 818 is from 4 mm to 45 mm.
The hazards covered by this Part of EN 818 are identified in clause 4.
The bases for calculation of tabulated values for dimensions, working load limits and mechanical properties are given in annex A.
Annex B gives information on weight/metre of chain.
Annex C gives an example of a designation system for chains.

Kurzgliedrige Rundstahlketten für Hebezwecke - Sicherheit - Teil 2: Mitteltolerierte Rundstahlketten für Anschlagketten - Güteklasse 8

Chaînes de levage à maillons courts - Sécurité - Partie 2: Chaînes de tolérance moyenne pour élingues en chaînes - Classe 8

!La présente partie de l’EN 818 spécifie les prescriptions relatives à la sécurité pour les chaînes de levage à maillons courts de classe 8, de tolérance moyenne utilisées dans les élingues en chaîne conformément à l’!EN 818-4:1996+A1" et pour les applications générales de levage". Il s'agit de chaînes à maillons courts en acier rond soudé électriquement, soumises à un traitement thermique, testées et conformes aux conditions générales de réception de l'!EN 818-1:1996+A1".
La gamme de dimensions nominales des chaînes couvertes par la présente partie de l'EN 818 va de 4 mm à 45 mm.
Les phénomènes dangereux couverts par la présente partie de l'EN 818 sont définis dans l'article 4.
Les bases pour le calcul des valeurs relatives aux dimensions, aux charges maximales d'utilisation et aux propriétés mécaniques, indiquées dans les tableaux, sont données dans l'annexe A.
L'annexe B donne une information sur la masse des chaînes.
L'annexe C donne un exemple de système de désignation des chaînes.

Kratkočlene okrogle verige za dvigovalne namene - Varnost - 2. del: Verige za obesne verige srednje tolerance - Kakovostni razred 8

General Information

Status
Published
Publication Date
01-Apr-2008
ICS
53.020.30 - Accessories for lifting equipment
Technical Committee
CEN/TC 168 - Chains, ropes, webbing, slings and accessories - safaty
Drafting Committee
CEN/TC 168 - Chains, ropes, webbing, slings and accessories - safaty
Current Stage
9020 - Submission to 2 Year Review Enquiry - Review Enquiry
Start Date
15-Apr-2024
Completion Date
15-Apr-2024
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 818-2:1999+A1:2008 - Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain slings - Grade 8

Relations

Merged From
EN 818-2:1996 - Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain slings - Grade 8
Effective Date
19-Jan-2023
Merged From
EN 818-2:1996/prA1 - Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain slings - Grade 8
Effective Date
19-Jan-2023

Buy Standard

EN 818-2:1999+A1:2008EN 818-2:1999+A1:2008
PreviousNext
Standard
EN 818-2:1999+A1:2008
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 818-2:1999+A1:2008
01-julij-2008
.UDWNRþOHQHRNURJOHYHULJH]DGYLJRYDOQHQDPHQH9DUQRVWGHO9HULJH]D
REHVQHYHULJHVUHGQMHWROHUDQFH.DNRYRVWQLUD]UHG
Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain
slings - Grade 8
Kurzgliedrige Rundstahlketten für Hebezwecke - Sicherheit - Teil 2: Mitteltolerierte
Rundstahlketten für Anschlagketten - Güteklasse 8
Chaînes de levage à maillons courts - Sécurité - Partie 2: Chaîne de tolérance moyenne
pour élingues en chaînes - Classe 8
Ta slovenski standard je istoveten z: EN 818-2:1996+A1:2008
ICS:
53.020.30 Pribor za dvigalno opremo Accessories for lifting
equipment
SIST EN 818-2:1999+A1:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 818-2:1996+A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2008
ICS 53.020.30 Supersedes EN 818-2:1996
English Version
Short link chain for lifting purposes - Safety - Part 2: Medium
tolerance chain for chain slings - Grade 8
Chaînes de levage à maillons courts - Sécurité - Partie 2: Kurzgliedrige Rundstahlketten für Hebezwecke - Sicherheit
Chaîne de tolérance moyenne pour élingues en chaînes - - Teil 2: Mitteltolerierte Rundstahlketten für Anschlagketten
Classe 8 - Güteklasse 8
This European Standard was approved by CEN on 7 March 1996 and includes Amendment 1 approved by CEN on 10 February 2008.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 818-2:1996+A1:2008: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 818-2:1996+A1:2008 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 !Terms and definitions".5
4 Hazards .6
5 Safety requirements .6
5.1 General.6
5.2 Dimensions.6
5.2.1 Nominal size of chain, d .6
n
5.2.2 Tolerance on material diameter (except at the weld).6
5.2.3 Weld diameter .7
5.2.4 Length dimensionally affected by welding .7
5.2.5 Pitch and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13411-3:2022(Main)
Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
SIST EN 13411-3:2023

This document deals with the requirements for the ferrule-securing of eyes and endless loops.
It also deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops.
This document applies to the ferrule-securing of eye terminations formed either by a Flemish eye or turn-back eye and covers ferrules made of non-alloy carbon steel and aluminium.
This document applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60 mm diameter conforming to EN 12385-4, lift ropes conforming to EN 12385-5 and spiral strand ropes conforming to EN 12385-10.
Type testing of ferrule-secured systems and manufacturing quality control requirements are also specified.
This document deals with all significant hazards, hazardous situations, and events relevant to this particular steel wire rope termination when used as intended and under conditions of use which are foreseeable by the manufacturer.
This document applies to terminations of steel wire ropes with ferrules and ferrule-securing which are manufactured after the date of this publication.
NOTE   One design of ferrule-secured turn-back eye termination using an oval aluminium ferule which satisfies the requirements of this document when securing ropes having rope grades up to and including 1960 is given for information in Annex A.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-7:2021(Main)
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
SIST EN 13411-7:2021

This document specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts.
This document covers those symmetric wedge sockets intended for use at temperatures between −20 °C and 100 °C.
This document only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A.
The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A.
This document deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
The hazards covered by this document are identified in Clause 4.
This document applies to symmetric wedge sockets, which are manufactured after the date of its publication.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-9:2021(Main)
Terminations for steel wire ropes - Safety - Part 9: Solid thimbles
SIST EN 13411-9:2021

This document specifies the minimum requirements for solid thimbles made of steel or cast iron for terminations of stranded steel wire ropes.
This document is applicable to ferrule-secured terminations with solid thimbles in combination with ferrules (see EN 13411-3), that have an efficiency factor KT of at least 0,9, and to spliced terminations with solid thimbles (see EN 13411-2), that have an efficiency factor KT of at least 0,8, which are used as accessories for steel wire ropes, such as slings or wire rope assemblies, having a lifting, lowering or load-bearing effect in hoisting equipment.
Examples of designs of solid thimbles which meet the requirements of this standard are given in informative Annexes B and C.
Round thimbles (thimble with rotational symmetry around the bore) are not subject to this document.
This document is applicable to ferrule-secured terminations that are manufactured after the date of publication of this document.
Hazards that are dealt with in this document are listed in Clause 4.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3266:2010/A1:2015(Amendment)
Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010/Amd 1:2015)
SIST EN ISO 3266:2010/A1:2016

2014-04-02 GVN: Draft for // ENQ received at ISO/CS (see ISO notification in dataservice on 2014-04-01).

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-8:2011(Main)
Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging
SIST EN 13411-8:2012

This European Standard specifies the minimum requirements for swage terminals and the securing of such terminals by a swaging process to carbon steel rope conforming to EN 12385-4 and EN 12385-5, spiral strand rope conforming to EN 12385-10 and stainless steel stranded rope.
This European Standard is not applicable to spiral rope incorporating full lock wires - see EN 12385-10 -, nor ropes with coverings and /or fillings (see 3.6.3 of EN 12385-2:2002+A1:2008).
This European Standard is applicable to swaged terminations that have a terminal efficiency factor, KT, of at least 0,9 and are used as part of a wire rope accessory such as a sling, or wire rope assembly that performs a raising, lowering, hauling or supporting function on lifting machinery.
This European Standard is applicable to terminals of the following types that are made of carbon or stainless steel:
-   open swage socket;
-   closed swage socket;
-   swage terminal with thread;
-   swage terminal end stop.
This European Standard deals with all significant hazards, hazardous situations and events relevant to swaged terminations, when used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4).
This European Standard applies to swaged terminations which are manufactured after the date of its publication.
This European Standard is not applicable to swaged terminations used for anchoring ropes to winch drums.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3266:2010(Main)
Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010)
SIST EN ISO 3266:2010

ISO 3266:2010 specifies the general characteristics, performance and critical dimensions necessary for interchangeability and compatibility with other components, of forged steel eyebolts grade 4 for general lifting purposes. These eyebolts can be used for axial and inclined loading.
ISO 3266:2010 specifies the dimensions of the eyes of eyebolts permitting direct connection with shackles of the same working load limit as those defined in ISO 2415. These dimensions also allow designs with a larger eye which can permit direct connection with sling hooks of similar working load limit.
ISO 3266:2010 covers all significant hazards, hazardous situations and events relevant to eyebolts grade 4.
ISO 3266:2010 is applicable to eyebolts grade 4 for use in the temperature range of -20 ºC to 200 ºC.
ISO 3266:2010 is not applicable to eyebolts which are not forged in one piece.
ISO 3266:2010 is not applicable to forged steel eyebolts grade 4 manufactured before the date of its publication as an International Standard.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1492-2:2000+A1:2008(Main)
Textile slings - Safety - Part 2: Roundslings made of man-made fibres for general purpose use
SIST EN 1492-2:2001+A1:2009

This European Standard specifies the requirements related to safety, including methods of rating and testing roundslings up to 40 tonnes working load limit (in straight lift) and two-, three-, and four-leg roundsling assemblies, with or without fittings, made of polyamide, polyester and polypropylene.
The roundslings covered by this Part of EN 1492 are intended for general purpose lifting operations, i.e. when used for lifting objects, materials or goods which require no deviations from the requirements, safety factors or WLL’s specified. Lifting operations not covered by this standard include the lifting of persons, potentially dangerous materials such as molten metal and acids, glass sheets, fissile materials, nuclear reactors and where special conditions apply.
Roundslings conforming to this European Standard are suitable for use and storage in the following temperature ranges:
a)   polyester and polyamide: -40 °C to 100 °C,
b)   polypropylene: -40 °C to 80 °C
This European Standard does not apply to the types of roundsling indicated below:
a)   roundslings designed for securing or lashing of cargoes to each other on pallets and platforms or in vehicles;
b)   slings of tubular webbing without filling.
This European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the use of roundslings when carried out in accordance with the instructions and specifications given by the manufacturer or authorized representative.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1677-5:2001+A1:2008(Main)
Components for slings - Safety - Part 5: Forged steel lifting hooks with latch - Grade 4
SIST EN 1677-5:2001+A1:2009

This Part of EN 1677 specifies requirements for forged steel lifting hooks of grade 4 having latch and eye up to 31,5 t WLL, mainly for use in:
-   chain slings according to EN 818-5
-   steel wire rope slings according to prEN 13414-1:1998
-   textile slings according to EN 1492-1, EN 1492-2.
intended for lifting objects, materials or goods.
This Part of EN 1677 does not apply to hand forged hooks.
The hazards covered by this Part of EN 1677 are identified in clause 4.
Annex A gives the bases for calculation of hook dimensions.
Annex B gives an example of a designation system for hooks of grade 4.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1492-4:2004+A1:2008(Main)
Textile slings - Safety - Part 4: Lifting slings for general service made from natural and man-made fibre ropes
SIST EN 1492-4:2004+A1:2009

This European Standard specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless slings, with or without fittings, made of sisal, hemp and manila 3- and 4-strand laid construction natural fibre ropes and polyamide, polyester and polypropylene 3- and 4-strand laid construction and 8-strand plaited construction man-made fibre ropes having a reference number in the range of 16 to 48 inclusive.
The fibre rope slings covered by this part of EN 1492 are intended for general purpose lifting operations, i.e. when used for lifting objects, materials or goods which require no deviations from the requirements, safety factors or working load limits specified. Lifting operations not covered by this standard would include the lifting of persons, potentially dangerous materials such as molten metal and acids, glass sheets, fissile materials, nuclear reactors and where special conditions apply.
Fibre rope slings conforming to this European Standard are suitable for use and storage in the following temperature ranges:
a) polyester and polyamide -40 °C to 100 °C,
b) manila, sisal, hemp and polypropylene -40 °C to 80 °C.
This European Standard does not apply to fibre rope sling assemblies rated by the trigonometric method.
This European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the use of fibre rope slings when carried out in accordance with the instructions and specification given by the manufacturer or authorized representative.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1677-4:2000+A1:2008(Main)
Components for slings - Safety - Part 4: Links, Grade 8
SIST EN 1677-4:2001+A1:2009

This part of EN 1677 specifies requirements for forged or welded steel master links, intermediate master links, master link assemblies and lower terminal links of grade 8 up to 132 t WLL, mainly for use in:
-   chain slings according to EN 818-4
-   steel wire rope slings
-   textile slings according to EN 1492-1:2000, EN 1492-2:2000.
intended for lifting objects, materials or goods.
This Part of EN 1677 does not apply to hand forged links.
The hazards covered by this Part of EN 1677 are identified in clause 4.
Annex ZA gives the relationship with EU-Directives.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day