EN ISO 29864:2019

Self adhesive tapes - Measurement of breaking strength and elongation at break (ISO 29864:2018)

This document specifies methods to measure the breaking strength and elongation at break of a self adhesive tape when it is subjected to a tensile force sufficient to cause it to break.
These test methods describe a procedure for testing 12 mm or 24 mm wide samples cut from supplied rolls of self adhesive tapes. Alternatively rolls of self adhesive tape up to 50 mm wide can be directly tested in their original width. In these circumstances the practical breaking strength and elongation will be typical of the manufacturer's cut edges. When newly cut sample pieces are tested, because of the better cutting of the edges, the results can be higher than would be found on commercial tape.

Klebebänder - Messung der Bruchkraft und der Reißdehnung (ISO 29864:2018)

Dieses Dokument legt Verfahren zur Messung der Bruchkraft und Reißdehnung eines Klebebandes fest, wenn dieses einer Zugkraft ausgesetzt wird, die zum Bruch des Bandes führt.
Mit diesen Prüfverfahren können Probestreifen mit einer Breite von 12 mm oder 24 mm geprüft werden, die von gelieferten Klebebandrollen abgeschnitten werden. Als Alternative können Klebebandrollen mit einer Breite bis 50 mm direkt in ihrer ursprünglichen Breite geprüft werden. Unter diesen Umständen ist die praktische Bruchkraft und Reißdehnung charakteristisch für die Schnittkanten des Herstellers. Beim Prüfen neu geschnittener Probestreifen können die Ergebnisse wegen der besseren Schnittkanten höher sein als bei handelsüblichen Bändern.

Rubans auto-adhésifs - Mesure de la résistance à la rupture et de l'allongement à la rupture (ISO 29864:2018)

Le présent document spécifie des méthodes pour mesurer la résistance à la rupture et l'allongement à la rupture d'un ruban auto-adhésif lorsqu'il est soumis à une force de traction suffisante pour provoquer sa rupture.
Ces méthodes d'essai décrivent un mode opératoire pour soumettre à l'essai des échantillons de rouleaux de ruban auto-adhésif de 12 mm ou 24 mm de largeur. Une autre solution consiste à soumettre à l'essai des rouleaux de ruban directement dans leur largeur initiale (au plus 50 mm). Dans ces conditions, la résistance et l'allongement à la rupture sont, en pratique, caractéristiques de la découpe des bords effectuée en usine. Lorsque les essais portent sur des échantillons fraîchement découpés, les résultats obtenus peuvent se révéler supérieurs à ceux qui l'auraient été en utilisant des rubans du commerce en raison de la meilleure découpe des bords.

Samolepilni trakovi - Merjenje utržne trdnosti in raztezka ob utrgu (ISO 29864:2018)

Ta dokument določa metode za merjenje utržne trdnosti in raztezka ob utrgu samolepilnega traku, kadar je izpostavljen natezni sili, ki zadostuje za pretrganje.
Te preskusne metode opisujejo postopek preskušanja 12-mm ali 24-mm širokih preskušancev, odrezanih od priloženih zvitkov samolepilnih trakov. Namesto tega lahko zvitke samolepilnega traku širine do 50 mm neposredno preizkusite v prvotni širini. V teh okoliščinah bosta utržna trdnost in raztezek taka kot v primeru tovarniško odrezanih robov. Pri preskušanju na novo razrezanih preskušancev so zaradi bolje odrezanih robov rezultati lahko boljši kot v primeru traku s prodajne police.

General Information

• Status: Published
• Publication Date: 04-Jun-2019
• Withdrawal Date: 30-Dec-2019
• ICS: 83.180 - Adhesives
• Technical Committee: CEN/TC 193 - Adhesives
• Drafting Committee: CEN/TC 193 - Adhesives
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 05-Jun-2019
• Due Date: 20-Jan-2021
• Completion Date: 05-Jun-2019
• Ref Project: SIST EN ISO 29864:2019 - Self adhesive tapes - Measurement of breaking strength and elongation at break (ISO 29864:2018)

Relations

• Replaces: EN 14410:2003 - Self adhesive tapes - Measurement of breaking strength and elongation at break
• Effective Date: 08-Aug-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2019
Nadomešča:
SIST EN 14410:2003
Samolepilni trakovi - Merjenje utržne trdnosti in raztezka ob utrgu (ISO 29864:2018)
Self adhesive tapes - Measurement of breaking strength and elongation at break (ISO
29864:2018)
Klebebänder - Messung der Bruchkraft und der Reißdehnung (ISO 29864:2018)
Rubans auto-adhésifs - Mesure de la résistance à la rupture et de l'allongement à la
rupture (ISO 29864:2018)
Ta slovenski standard je istoveten z: EN ISO 29864:2019
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 29864
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 14410:2003
English Version
Self adhesive tapes - Measurement of breaking strength
and elongation at break (ISO 29864:2018)
Rubans auto-adhésifs - Mesure de la résistance à la Klebebänder - Messung der Bruchkraft und der
rupture et de l'allongement à la rupture (ISO Reißdehnung (ISO 29864:2018)
29864:2018)
This European Standard was approved by CEN on 8 April 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 29864:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 29864:2018 has been prepared by Technical Committee ISO/TC 61 "Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 29864:2019 by
Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14410:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 29864:2018 has been approved by CEN as EN ISO 29864:2019 without any modification.

INTERNATIONAL ISO
STANDARD 29864
Second edition
2018-05
Self adhesive tapes — Measurement
of breaking strength and elongation
at break
Rubans auto-adhésifs — Mesure de la résistance à la rupture et de
l'allongement à la rupture
Reference number
ISO 29864:2018(E)
©
ISO 2018
ISO 29864:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 29864:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Significance and use . 1
5 Principle . 2
6 Apparatus . 2
6.1 Tensile testing machine . 2
6.2 Clamps . 2
6.3 Cylinders . 2
6.4 Scale . 3
6.5 Cutting tool . 3
7 Test sample and test pieces . 3
8 Procedure. 3
8.1 Testing conditions . 3
8.2 Preparation of test pieces . 4
8.3 Method A for non-filament tapes . 4
8.4 Method B for filament tapes . 4
9 Expression of results . 4
9.1 Expression of results for non-filament tapes . 4
9.2 Expression of results for filament tapes . 5
10 Test report . 5
ISO 29864:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This second edition cancels and replaces the first edition (ISO 29864:2007) of which it constitutes a
minor revision.
The changes compared to the previous edition are as follows:
— the Introduction has been editorially revised;
— the normative references in Clause 2 have been updated;
— a definition has been added for “self adhesive tape” in Clause 3;
— the text has been editorially revised to comply with the most recent editing rules.
iv © ISO 2018 – All rights reserved

ISO 29864:2018(E)
Introduction
The breaking strength of adhesive tape is of value as an indication of its uniformity and quality, and its
ability to withstand stresses during application and use.
The elongation at break of the adhesive tape is of value as an indication of its uniformity and quality
as well as a rough indication of its ability to conform to curved and irregular surfaces. It is usually
determined at the same time as the breaking strength.
The procedure specified in this document combines the determination of breaking strength and
elongation at break.
Method A is the measurement of breaking strength and elongation at break of tapes other than
filament tapes.
Method B is the measurement of breaking strength and elongation at break of filament reinforced tapes.
INTERNATIONAL STANDARD ISO 29864:2018(E)
Self adhesive tapes — Measurement of breaking strength
and elongation at break
1 Scope
This document specifies methods to measure the breaking strength and elongation at break of a self
adhesive tape when it is subjected to a tensile force sufficient to cause it to break.
These test methods describe a procedure for testing 12 mm or 24 mm wide samples cut from supplied
rolls of self adhesive tapes. Alternatively rolls of self a
...