iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15216:2021

(Main)

Environmental solid matrices - Determination of total dissolved solids (TDS) in water and eluates

Environmental solid matrices - Determination of total dissolved solids (TDS) in water and eluates

This document specifies a method for the determination of total dissolved solids (TDS) in water and eluates (see Annex A), provided they are not volatile under the conditions specified or that they do not release water molecules from hydration. It applies to water and eluates containing more than 100 mg/l of total dissolved solids. Samples with lower amounts of dissolved solids can be analysed by repetition of the drying step.

Feststoffe in der Umwelt - Bestimmung des Gesamtgehaltes an gelösten Feststoffen (TDS) in Wasser und Eluaten

Dieses Dokument legt ein Verfahren zur Bestimmung des Gesamtgehaltes an gelösten Feststoffen (TDS) in Wasser und Eluaten fest (siehe Anhang A), sofern sie nicht unter den angegebenen Bedingungen flüchtig sind bzw. keine Wassermoleküle aus Kristallwasser freisetzen. Das Dokument gilt für Wasser und Eluate mit einem Gesamtgehalt an gelösten Feststoffen von mehr als 100 mg/l. Proben mit niedrigeren Gehalten an gelösten Feststoffen können durch Wiederholung des Trockenschritts analysiert werden.

Matrices environnementales solides - Détermination de la concentration en matières solides dissoutes totales (TDS) de l'eau et des éluats

Le présent document spécifie une méthode permettant de déterminer la concentration en matières solides dissoutes totales (TDS) dans l’eau et les éluats (voir l’Annexe A) pourvu que ces matières ne soient pas volatiles dans les conditions spécifiées ou qu’elles ne relarguent pas de molécules d’eau d’hydratation. Il s’applique à l’eau et aux éluats contenant plus de 100 mg/l de matières solides dissoutes totales. Les échantillons contenant des quantités moindres de matières solides dissoutes peuvent être analysés en répétant l’étape de dessiccation.

Matriksi z vidika okolja - Določevanje celotnih trdnih raztopljenih snovi (TDS) v vodi in izlužkih

Ta evropski standard določa metodo za določevanje celotnih trdnih raztopljenih snovi (TDS) v vodi in izlužkih, če niso hlapni pod določenimi pogoji oziroma se pri njihovi hidrataciji ne sproščajo molekule vode. Uporablja se za vodo in izlužke, ki vsebujejo več kot 200 mg/l skupnih trdnih raztopljenih snovi. Vzorce z nižjo vsebnostjo trdnih raztopljenih snovi je mogoče analizirati s ponovitvijo postopka sušenja.

General Information

Status
Published
Publication Date
19-Oct-2021
Withdrawal Date
29-Apr-2022
ICS
13.030.20 - Liquid wastes. Sludge
Technical Committee
CEN/TC 444 - Environmental characterization
Drafting Committee
CEN/TC 444/WG 5 - Physical tests
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Oct-2021
Due Date
12-Jan-2021
Completion Date
20-Oct-2021
Ref Project
SIST EN 15216:2022 - Environmental matrices - Determination of total dissolved solids (TDS) in water and eluates

Relations

Replaces
EN 15216:2007 - Characterization of waste - Determination of total dissolved solids (TDS) in water and eluates
Effective Date
27-Oct-2021

Buy Standard

EN 15216:2022EN 15216:2022
PreviousNext
Standard
EN 15216:2022
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15216:2022
01-januar-2022
Nadomešča:
SIST EN 15216:2008
Matriksi z vidika okolja - Določevanje celotnih trdnih raztopljenih snovi (TDS) v
vodi in izlužkih
Environmental matrices - Determination of total dissolved solids (TDS) in water and
eluates
Umweltrelevante Matrizes - Bestimmung des Gesamtgehaltes an gelösten Feststoffen
(TDS) in Wasser und Eluaten
Matrices environnementales - Détermination de la concentration en matières solides
dissoutes totales (TDS) de l'eau et des éluats
Ta slovenski standard je istoveten z: EN 15216:2021
ICS:
13.030.20 Tekoči odpadki. Blato Liquid wastes. Sludge
SIST EN 15216:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 15216:2022

---------------------- Page: 2 ----------------------
SIST EN 15216:2022


EN 15216
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 13.030.20 Supersedes EN 15216:2007
English Version

Environmental solid matrices - Determination of total
dissolved solids (TDS) in water and eluates
Matrices environnementales solides - Détermination Umweltrelevante Matrizes - Bestimmung des
de la concentration en matières solides dissoutes Gesamtgehaltes an gelösten Feststoffen (TDS) in
totales (TDS) de l'eau et des éluats Wasser und Eluaten
This European Standard was approved by CEN on 11 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15216:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 15216:2022
EN 15216:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Sample storage and preparation . 5
6 Equipment . 5
7 Procedure. 6
8 Calculation of results . 6
9 Test report . 7
Annex A (informative) Performance characteristics . 8
Bibliography .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 54321:2021(Main)
Soil, treated biowaste, sludge and waste - Digestion of aqua regia soluble fractions of elements (ISO 54321:2020)
SIST EN ISO 54321:2021

This document specifies two methods for digestion of soil, treated biowaste, sludge and waste by the use of an aqua regia digestion.
Digestion with aqua regia will not necessarily accomplish total decomposition of the sample. The extracted analyte concentrations may not necessarily reflect the total content in the sample but represent the aqua regia soluble metals under the condition of this test procedure. It is generally agreed that for environmental analysis purposes, the results are fit for the intended purpose to protect the environment.
This document is applicable for the following elements:
Aluminium (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), boron (B), cadmium (Cd), calcium (Ca), chromium (Cr), cobalt (Co), copper (Cu), iron (Fe), lead (Pb), magnesium (Mg), manganese (Mn), mercury (Hg), molybdenum (Mo), nickel (Ni), phosphorus (P), potassium (K), selenium (Se), silver (Ag), sodium (Na), strontium (Sr), sulfur (S), tellurium (Te), thallium (Tl), tin (Sn), titanium (Ti), vanadium (V), and zinc (Zn).
This document can also be applied for the digestion of other elements, provided the user has verified the applicability.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17322:2020(Main)
Environmental Solid Matrices - Determination of polychlorinated biphenyls (PCB) by gas chromatography - mass selective detection (GC-MS) or electron-capture detection (GC-ECD)
SIST EN 17322:2020

This document specifies methods for quantitative determination of seven selected polychlorinated biphenyls (PCB28, PCB52, PCB101, PCB118, PCB138, PCB153 and PCB180) in soil, sludge, sediment, treated biowaste, and waste using GC-MS and GC-ECD (see Table 2).
The limit of detection depends on the determinants, the equipment used, the quality of chemicals used for the extraction of the sample and the clean-up of the extract.
Under the conditions specified in this document, lower limit of application from 1 μg/kg (expressed as dry matter) for soils, sludge and biowaste to 10 μg/kg (expressed as dry matter) for solid waste can be achieved. For some specific samples the limit of 10 μg/kg cannot be reached.
Sludge, waste and treated biowaste may differ in properties, as well as in the expected contamination levels of PCB and presence of interfering substances. These differences make it impossible to describe one general procedure. This document contains decision tables based on the properties of the sample and the extraction and clean-up procedure to be used.
NOTE   The analysis of PCB in insulating liquids, petroleum products, used oils and aqueous samples is referred to in EN 61619, EN 12766-1 and EN ISO 6468 respectively.
The method can be applied to the analysis of other PCB congeners not specified in the scope, provided suitability is proven by proper in-house validation experiments.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-4:2006(Main)
Characterization of waste - Sampling of waste materials - Part 4: Guidance on procedures for sample packaging, storage, preservation, transport and delivery
SIST-TP CEN/TR 15310-4:2007

This Technical Report describes procedures for the packaging, preservation, short-term storage and transport of both solid and liquid waste samples, including paste-like substances and sludges. Where available and appropriate for field application, requirements for specific storage conditions and/or preservation methods should be selected from the chosen analytical standard and collaboration with the testing laboratory.
NOTE 1   This Technical Report provides a shop shelf of example sampling techniques that can be selected to meet a wide range of sampling situations. For a specific situation one of the presented procedures may be appropriate.
NOTE 2   The procedures listed in this Technical Report reflect current best practice, but these are not exhaustive and other procedures may be equally relevant.

  • Technical report
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-5:2006(Main)
Characterization of waste - Sampling of waste materials - Part 5: Guidance on the process of defining the sampling plan
SIST-TP CEN/TR 15310-5:2007

This Technical Report provides guidance on process of defining of a Sampling Plan based on the objective of the testing programme. It specifically deals with the strategic decisions that are needed, based on the sampling objective.
NOTE 1   Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence).
NOTE 2    The document provides considerable detail on current best practice, but is not exhaustive.
NOTE 3   To clarify the text, the document provides a number of worked examples.

  • Technical report
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-2:2006(Main)
Characterization of waste - Sampling of waste materials - Part 2: Guidance on sampling techniques
SIST-TP CEN/TR 15310-2:2007

This Technical Report describes techniques for sampling liquid and granular waste material, including paste-like materials and sludges, found in a variety of locations. The Technical Report provides information to allow the selection and preparation of equipment and apparatus to be used in the sampling activity.
NOTE 1   This Technical Report provides a shop shelf of example sampling techniques that can be selected to meet a wide range of sampling situations. For a specific situation one of the presented procedures may be appropriate.
NOTE 2    The procedures listed in this Technical Report reflect current best practice, but these are not exhaustive and other procedures may be equally relevant.

  • Technical report
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-1:2006(Main)
Characterization of waste - Sampling of waste materials - Part 1: Guidance on selection and application of criteria for sampling under various conditions
SIST-TP CEN/TR 15310-1:2007

This Technical Report discusses the statistical principles of sampling, and provides a number of statistical tools to assist in the design of testing programmes for application to sampling under various conditions.
NOTE 1   Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence).
NOTE 2   The document provides considerable detail on current best practice, but is not exhaustive.
NOTE 3   To clarify the text, the document provides a number of worked examples.

  • Technical report
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-4:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction)
SIST EN 12457-4:2004

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 10 mm without or with limited size reduction. Note: In some cases, it could be useful to test the material with coarser particles up to 40 mm in diameter: This requires a larger amount for material and liquid.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-1:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 1: One stage batch test at a liquid to solid ratio of 2 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction)
SIST EN 12457-1:2004

This part of European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 2 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. The test procedure specified in this Standard produces an eluate which shall subsequently be characterized physically and chemically according to appropriate standard methods.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-3:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction)
SIST EN 12457-3:2004

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 2 l/kg dry matter and subsequently of 8 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. The test procedure specified in this Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-2:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 4 mm (without or with size reduction)
SIST EN 12457-2:2004

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. The test procedure specified in this Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day