prEN 590
(Main)Automotive fuels - Diesel - Requirements and test methods
Automotive fuels - Diesel - Requirements and test methods
This document specifies requirements and test methods for marketed and delivered automotive diesel fuel. It is applicable to automotive diesel fuel for use in diesel engine vehicles designed to run on automotive diesel fuel containing up to 7,0 %(V/V) Fatty Acid Methyl Ester (FAME).
NOTE For the purposes of this document, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction and the volume fraction.
Kraftstoffe - Dieselkraftstoff - Anforderungen und Prüfverfahren
Dieses Dokument legt Anforderungen an und Prüfverfahren für gelieferte und in Verkehr gebrachte Dieselkraftstoffe fest. Es ist anwendbar auf Dieselkraftstoff für die Verwendung in Kraftfahrzeugen mit Dieselmotoren, die für den Betrieb mit Dieselkraftstoff mit einem Gehalt an Fettsäure-Methylestern (FAME) von bis zu 7,0 % (V/V) ausgelegt sind.
ANMERKUNG Für die Zwecke dieses Dokuments wird zur Angabe des Massenanteils einer Substanz der Ausdruck „% (m/m)“ und für den Volumenanteil einer Substanz der Ausdruck „% (V/V)“ verwendet.
Carburants pour automobiles - Carburants pour moteur diesel (gazole) — Exigences et méthodes d'essai
Le présent document spécifie des exigences et méthodes d'essai pour le carburant pour moteur diesel (gazole) mis sur le marché et livré. Il est applicable au gazole destiné aux véhicules à moteur diesel conçus pour utiliser ce type de carburant contenant jusqu’à 7,0 % (V/V) d’esters méthyliques d’acides gras (EMAG).
NOTE Pour les besoins du présent document, les expressions « % (m/m) » et « % (V/V) » sont utilisées pour désigner respectivement les fractions massiques et les fractions volumiques.
Goriva za motorna vozila - Dizelsko gorivo - Zahteve in preskusne metode
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2024
Goriva za motorna vozila - Dizelsko gorivo - Zahteve in preskusne metode
Automotive fuels - Diesel - Requirements and test methods
Kraftstoffe - Dieselkraftstoff - Anforderungen und Prüfverfahren
Carburants pour automobiles - Carburants pour moteur diesel (gazole) - Exigences et
méthodes d'essai
Ta slovenski standard je istoveten z: prEN 590
ICS:
75.160.20 Tekoča goriva Liquid fuels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2024
ICS 75.160.20 Will supersede EN 590:2022
English Version
Automotive fuels - Diesel - Requirements and test methods
Carburants pour automobiles - Combustibles pour Kraftstoffe für Kraftfahrzeuge - Dieselkraftstoff -
moteurs diesel (gazole) - Exigences et méthodes Anforderungen und Prüfverfahren
d'essai
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 19.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 590:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Sampling . 7
5 Pump marking . 7
6 Requirements and test methods . 7
6.1 Dyes and markers . 7
6.2 Additives . 7
6.2.1 General . 7
6.2.2 Methylcyclopentadienyl manganese tricarbonyl (MMT) . 7
6.3 Fatty acid methyl ester (FAME) . 7
6.4 Other (bio-) components . 8
6.5 Particle count . 8
6.5.1 Requirements . 8
6.5.2 Test method . 9
6.6 Generally applicable requirements and related test methods . 9
6.7 Climate-dependent requirements and related test methods . 11
6.8 Precision and dispute . 13
Annex A (informative) Further information regarding particle count requirements . 15
Bibliography . 19
European foreword
This document (prEN 590:2024) has been prepared by Technical Committee CEN/TC 19 Gaseous and
liquid fuels, lubricants and related products of petroleum, synthetic and biological origin, the secretariat
of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 590:2022.
This document has originally been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association [6].
Requirements following amendment 2003/17/EC [2], 2009/30/EC [3], 2011/63/EU [4] and
2014/77/EU [5] to the European Fuels Quality Directive 98/70/EC [1], are taken into account. Dates are
included with all normative test method references for properties required by Annex II of the Fuels
Quality Directive in order to comply with the requirements of the European Commission; with the
accompanying assurance by CEN/TC 19 that any referenced updated versions will always give similar
accuracy and the same or better precision (see [4]).
The marking at the pump of this product is in line with the requirements of the Fuels Quality Directive
and the Alternative Fuels Infrastructure Directive [7].
Further significant technical changes between this document and the previous edition are EN 590:2022:
— introduction of Clause 3 “Terms and definitions”;
— inclusion of a particle count limit of 10,000 counts/ml for particles ≥ 4 μm at “the point of particle
certification” in a new Table 2 and 6.5;
— introduction of test method IP 630 procedure A and B to measure the number of particles ≥ 4 μm in
diesel fuel;
— addition of the constant pressure viscometer method (EN ISO 18335) as an alternative test method
to viscosity by EN ISO 3104;
3 3
— a reduction of the minimum density for summer grades (A, B, C) from 820,0 kg/m to 815,0 kg/m
and the displacement of the parameter to Table 1;
— addition of Annex A “Further information regarding particle count requirements”.
1 Scope
This document specifies requirements and test methods for marketed and delivered automotive diesel
fuel. It is applicable to automotive diesel fuel for use in diesel engine vehicles designed to run on
automotive diesel fuel containing up to 7,0 %(V/V) Fatty Acid Methyl Ester (FAME).
NOTE For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent
respectively the mass fraction and the volume fraction.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 116, Diesel and domestic heating fuels — Determination of cold filter plugging point - Stepwise cooling
bath method
EN 12662-1, Liquid petroleum products — Determination of total contamination — Part 1: Middle
distillates and diesel fuels
EN 12916:2024, Petroleum products — Determination of aromatic hydrocarbon types in middle distillates
— High performance liquid chromatography method with refractive index detection
EN 14078:2014, Liquid petroleum products — Determination of fatty acid methyl ester (FAME) content in
middle distillates — Infrared spectrometry method
EN 14214:2012+A2:2019, Liquid petroleum products — Fatty acid methyl esters (FAME) for use in diesel
engines and heating applications — Requirements and test methods
EN 15195:2023, Liquid petroleum products — Determination of ignition delay and derived cetane number
(DCN) of middle distillate fuels by combustion in a constant volume chamber
EN 15751, Automotive fuels — Fatty acid methyl ester (FAME) fuel and blends with diesel fuel —
Determination of oxidation stability by accelerated oxidation method
EN 16091, Liquid petroleum products — Middle distillates and fatty acid methyl ester (FAME) fuels and
blends — Determination of oxidation stability by rapid small scale oxidation test (RSSOT)
EN 16329, Diesel and domestic heating fuels — Determination of cold filter plugging point — Linear cooling
bath method
EN 16576:2014, Automotive fuels — Determination of manganese and iron content in diesel — Inductively
coupled plasma optical emission spectrometry (ICP OES) method
EN 16715:2015, Liquid petroleum products — Determination of ignition delay and derived cetane number
(DCN) of middle distillate fuels — Ignition delay and combustion delay determination using a constant
volume combustion chamber with direct fuel injection
EN 16906:2023, Liquid petroleum products — Determination of the ignition quality of diesel fuels — Fixed
compression ratio engine method
EN 16942, Fuels — Identification of vehicle compatibility — Graphical expression for consumer information
EN 17155:2018, Liquid petroleum products — Determination of indicated cetane number (ICN) of middle
distillate fuels — Primary reference fuels calibration method using a constant volume combustion chamber
EN 17306:2023, Liquid petroleum products — Determination of distillation characteristics at atmospheric
pressure — Micro-distillation
EN ISO 2160, Petroleum products — Corrosiveness to copper — Copper strip test (ISO 2160)
EN ISO 2719, Determination of flash point — Pensky-Martens closed cup method (ISO 2719)
EN ISO 3015, Petroleum and related products from natural or synthetic sources — Determination of cloud
point (ISO 3015)
EN ISO 3104, Petroleum products — Transparent and opaque liquids — Determination of kinematic
viscosity and calculation of dynamic viscosity (ISO 3104)
EN ISO 3170, Petroleum liquids — Manual sampling (ISO 3170)
EN ISO 3171, Petroleum liquids — Automatic pipeline sampling (ISO 3171)
EN ISO 3405:2019, Petroleum and related products from natural or synthetic sources — Determination of
distillation characteristics at atmospheric pressure (ISO 3405:2019)
EN ISO 3675:1998, Crude petroleum and liquid petroleum products — Laboratory determination of density
— Hydrometer method (ISO 3675:1998)
EN ISO 3924:2019, Petroleum products — Determination of boiling range distribution — Gas
chromatography method (ISO 3924:2019)
EN ISO 4259-2, Petroleum and related products — Precision of measurement methods and results — Part
2: Interpretation and application of precision data in relation to methods of test (ISO 4259-2)
EN ISO 4264, Petroleum products — Calculation of cetane index of middle-distillate fuels by the four
variable equation (ISO 4264)
EN ISO 5165:2020, Petroleum products — Determination of the ignition quality of diesel fuels — Cetane
engine method (ISO 5165:2020)
EN ISO 6245, Petroleum products — Determination of ash (ISO 6245)
EN ISO 10370, Petroleum products — Determination of carbon residue — Micro method (ISO 10370)
EN ISO 12156-1, Diesel fuel — Assessment of lubricity using the high-frequency reciprocating rig (HFRR) —
Part 1: Test method (ISO 12156-1)
EN ISO 12185:2024, Crude petroleum, petroleum products and related products — Determination of
density — Laboratory density meter with an oscillating U tube sensor (ISO 12185:2024)
EN ISO 12205, Petroleum products — Determination of the oxidation stability of middle-distillate fuels
(ISO 12205)
EN ISO 12937, Petroleum products — Determination of water — Coulometric Karl Fischer titration method
(ISO 12937)
EN ISO 13032:2012, Petroleum products —Determination of low concentration of sulfur in automotive
fuels — Energy-dispersive X-ray fluorescence spectrometric method (ISO 13032:2012)
EN ISO 13759, Petroleum products — Determination of alkyl nitrate in diesel fuels — Spectrometric method
(ISO 13759)
EN ISO 18335, Petroleum products and related products — Determination of kinematic viscosity by
calculation from the measured dynamic viscosity and density — Method by constant pressure viscometer
(ISO 18335)
EN ISO 20846:2019, Petroleum products — Determination of sulfur content of automotive fuels —
Ultraviolet fluorescence method (ISO 20846:2019)
EN ISO 20884:2019, Petroleum products — Determination of sulfur content of automotive fuels —
Wavelength-dispersive X-ray fluorescence spectrometry (ISO 20884:2019)
EN ISO 20884:20
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.