Petroleum products - Determination of boiling range distribution - Gas chromatography method (ISO 3924:2010)

ISO 3924:2010 specifies a method for the determination of the boiling-range distribution of petroleum products. The method is applicable to petroleum products and fractions with a final boiling point of 538 °C or lower at atmospheric pressure as determined by this International Standard. ISO 3924:2010 is not applicable to gasoline samples or gasoline components. The method is limited to products having a boiling range greater than 55 °C and having a vapour pressure sufficiently low to permit sampling at ambient temperature.
ISO 3924:2010 has successfully been applied to samples containing biodiesel up to 10 %.

Mineralölerzeugnisse - Bestimmung der Siedebereichsverteilung - Gaschromatographisches Verfahren (ISO 3924:2010)

Diese Internationale Norm legt ein Verfahren zur Bestimmung des Siedeverlaufes von Mineralölerzeugnissen
fest. Das Verfahren ist anwendbar auf Mineralölprodukte und Fraktionen mit einem Siedeendpunkt von 538 °C
oder niedriger bei Atmosphärendruck, wie nach dieser Internationalen Norm bestimmt. Diese Internationale
Norm ist nicht anwendbar auf Ottokraftstoff oder dessen Komponenten. Das Verfahren ist beschränkt auf
Produkte mit einem Siedebereich größer als 55 °C und mit einem Dampfdruck, der niedrig genug ist, um eine
Probenahme bei Umgebungstemperatur zu erlauben.
Dieses Verfahren wurde bereits erfolgreich auf Proben mit Gehalten an Biodiesel bis zu 10 % (V/V) angewandt.
ANMERKUNG Für die Zwecke dieses Dokuments wird zur Angabe des Massenanteils einer Substanz der Ausdruck
% (m/m)“ und für den Volumenanteil einer Substanz der Ausdruck % (V/V) verwendet.

Produits pétroliers - Détermination de la répartition dans l'intervalle de distillation - Méthode par chromatographie en phase gazeuse (ISO 3924:2010)

L'ISO 3924:2010 spécifie une méthode pour déterminer la répartition dans l'intervalle de distillation des produits pétroliers. La méthode est applicable aux produits pétroliers et aux fractions pétrolières dont le point final de distillation est inférieur ou égal à 538 °C à la pression atmosphérique quand il est déterminé selon l'ISO 3924:2010. L'ISO 3924:2010 n'est pas applicable aux échantillons d'essences ou aux composés à base d'essences. La méthode est limitée aux produits dont l'intervalle de distillation est supérieur à 55 °C et dont la pression de vapeur est suffisamment basse pour permettre un échantillonnage à la température ambiante.
L'ISO 3924:2010 a été appliquée avec succès à des échantillons contenant du biodiesel jusqu'à 10 %.

Naftni proizvodi - Določevanje destilacijskega območja - Metoda plinske kromatografije (ISO 3924:2010)

Ta mednarodni standard opredeljuje metodo za določevanje destilacijskega območja naftnih proizvodov. Metoda se uporablja za naftne proizvode in frakcije s končnim vreliščem 538°C ali nižjim pri atmosferskem tlaku, kot določa ta mednarodni standard. Ta mednarodni standard se ne uporablja za vzorce goriva ali sestavine goriva. Metoda je omejena na proizvode, ki imajo vrelišče višje od 55°C in imajo dovolj nizek parni tlak, da omogoča vzorčenje pri temperaturi prostora. Metoda je bila uspešno uporabljena za vzorce, ki vsebujejo biodizel do 10 %.

General Information

Status
Withdrawn
Publication Date
14-Feb-2010
Withdrawal Date
04-Oct-2016
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
05-Oct-2016

Relations

Buy Standard

Standard
EN ISO 3924:2010
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2010
1DIWQLSURL]YRGL'RORþHYDQMHGHVWLODFLMVNHJDREPRþMD0HWRGDSOLQVNH
NURPDWRJUDILMH ,62
Petroleum products - Determination of boiling range distribution - Gas chromatography
method (ISO 3924:2010)
Mineralölerzeugnisse - Bestimmung der Siedebereichsverteilung -
Gaschromatographisches Verfahren (ISO 3924:2010)
Produits pétroliers - Détermination de la répartition dans l'intervalle de distillation -
Méthode par chromatographie en phase gazeuse (ISO 3924:2010)
Ta slovenski standard je istoveten z: EN ISO 3924:2010
ICS:
75.080 Naftni proizvodi na splošno Petroleum products in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 3924
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2010
ICS 75.080
English Version
Petroleum products - Determination of boiling range distribution -
Gas chromatography method (ISO 3924:2010)
Produits pétroliers - Détermination de la répartition dans Mineralölerzeugnisse - Bestimmung der
l'intervalle de distillation - Méthode par chromatographie en Siedebereichsverteilung - Gaschromatographisches
phase gazeuse (ISO 3924:2010) Verfahren (ISO 3924:2010)
This European Standard was approved by CEN on 13 February 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3924:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 3924:2010) has been prepared by Technical Committee CEN/TC 19 "Gaseous and
liquid fuels, lubricants and related products of petroleum, synthetic and biological origin" the secretariat of
which is held by NEN, in collaboration with Technical Committee ISO/TC 28 "Petroleum products and
lubricants".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2010, and conflicting national standards shall be withdrawn at
the latest by August 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
INTERNATIONAL ISO
STANDARD 3924
Third edition
2010-02-15
Petroleum products — Determination of
boiling range distribution — Gas
chromatography method
Produits pétroliers — Détermination de la répartition dans l'intervalle de
distillation — Méthode par chromatographie en phase gazeuse

Reference number
ISO 3924:2010(E)
©
ISO 2010
ISO 3924:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved

ISO 3924:2010(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Principle.2
5 Reagents and materials .2
6 Apparatus.4
7 Sampling.6
8 Preparation of apparatus.6
9 Calibration.9
10 Procedure.12
11 Calculation .13
12 Expression of results.13
13 Precision.14
14 Test report.15
Annex A (informative) Calculation of ISO 3405-equivalent data .16
Annex B (informative) Accelerated analysis .18
Annex C (informative) Boiling points of non-normal alkane hydrocarbons .20
Bibliography.24

ISO 3924:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3924 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 19, Gaseous and liquid fuels, lubricants and related products of petroleum, synthetic and biological
origin, in collaboration with Technical Committee ISO/TC 28, Petroleum products and lubricants, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
[3] [4]
This method is harmonized with the analogous IP 406 and ASTM D2887 methods.
This third edition cancels and replaces the second edition (ISO 3924:1999), to which two additional
informative annexes, Annexes A and B, have been added and some updating on definitions has been
incorporated. (The Annex A in ISO 3924:1999 has become Annex C in this revised edition.) Annex A basically
contains a table for a correlation of certain data with those obtained using the ISO 3405 method and some
extra wording to the basic procedure, without changing the scope. With this information, the revised ISO 3924
becomes an updated document, describing the method actually in practice without changing the basic
procedure. The data presented in Annex A allow a reference in modern, global specifications, such as for
aviation fuels. This underlines the fact that availability of these chemical data in an ISO method supports their
use in these specific fields.
Also, because ISO 3924 is extensively used and referenced in many fuel specifications and there is a
requirement for a faster method, Annex B describes a method that, without any instrumental adaptation,
reduces the analysis time by a factor 5.

iv © ISO 2010 – All rights reserved

INTERNATIONAL STANDARD ISO 3924:2010(E)

Petroleum products — Determination of boiling range
distribution — Gas chromatography method
WARNING — The use of this International Standard may involve hazardous materials, operations and
equipment. This International Standard does not purport to address all of the safety problems
associated with its use. It is the responsibility of the user of this International Standard to establish
appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
1 Scope
This International Standard specifies a method for the determination of the boiling-range distribution of
petroleum products. The method is applicable to petroleum products and fractions with a final boiling point of
538 °C or lower at atmospheric pressure as determined by this International Standard. This International
Standard is not applicable to gasoline samples or gasoline components. The method is limited to products
having a boiling range greater than 55 °C and having a vapour pressure sufficiently low to permit sampling at
ambient temperature.
The method has successfully been applied to samples containing biodiesel up to 10 %.
NOTE For the purposes of this International Standard, the term “% (m/m)” is used to represent the mass fraction of a
material.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3170:2004, Petroleum liquids — Manual sampling
ISO 3171:1988, Petroleum liquids — Automatic pipeline sampling
ISO 3405:2000, Petroleum products — Determination of distillation characteristics at atmospheric pressure
ISO 4259:2006, Petroleum products — Determination and application of precision data in relation to methods
of test
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
initial boiling point
IBP
temperature corresponding to the retention time at which a net area count equal to 0,5 % of the total sample
a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.