EN 12941:1998/A1:2003

Respiratory protective devices - Powered filtering devices incorporating a helmet or a hood - Requirements, testing, marking

This European Standard specifies minimum requirements for powered filtering devices incorporating a helmet or a hood with gas, particle or combined filter(s) for respiratory protection. It does not cover devices designed for use in circumstances where there is or might be an oxygen deficiency (oxygen less than 17 % by volume). Also, it does not cover respiratory protective devices designed for escape purposes.  Laboratory and practical performance tests are included for the assessment of compliance with the requirements.

Atemschutzgeräte - Gebläsefiltergeräte mit einem Helm oder einer Haube - Anforderungen, Prüfung, Kennzeichnung

Appareils de protection respiratoire - Appareils filtrants à ventilation assistée avec casque ou cagoule - Exigences, essais, marquage

Oprema za varovanje dihal – Zaščitna čelada ali kapuca s tlačno filtracijo zraka – Zahteve, preskušanje, označevanje

General Information

• Status: Withdrawn
• Publication Date: 16-Dec-2003
• Withdrawal Date: 19-Dec-2023
• ICS: 13.340.30 - Respiratory protective devices
• Technical Committee: CEN/TC 79 - Respiratory protective devices
• Drafting Committee: CEN/TC 79/SC 8 - Powered respirators
• Directive: 2016/425 - Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment and repealing Council Directive 89/686/EEC
• Directive: 89/686/EEC - Council Directive 89/686/EEC of 21 December 1989 on the approximation of the laws of the Member States relating to personal protective equipment
• Mandate: M/031 - Standardization mandate to CEN/CENELEC concerning standards for Personal Protective Equipment
• Ref Project: SIST EN 12941:1999/A1:2004 - Respiratory protective devices - Powered filtering devices incorporating a helmet or a hood - Requirements, testing, marking

Relations

• Replaced By: EN 12941:2023 - Respiratory protective devices - Powered filtering devices incorporating a loose fitting respiratory interface - Requirements, testing, marking
• Effective Date: 27-Dec-2023
• Amends: EN 12941:1998 - Respiratory protective devices - Powered filtering devices incorporating a helmet or a hood - Requirements, testing, marking
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12941:1999/A1:2004
01-februar-2004
2SUHPD]DYDURYDQMHGLKDO±=DãþLWQDþHODGDDOLNDSXFDVWODþQRILOWUDFLMR]UDND±
=DKWHYHSUHVNXãDQMHR]QDþHYDQMH
Respiratory protective devices - Powered filtering devices incorporating a helmet or a
hood - Requirements, testing, marking
Atemschutzgeräte - Gebläsefiltergeräte mit einem Helm oder einer Haube -
Anforderungen, Prüfung, Kennzeichnung
Appareils de protection respiratoire - Appareils filtrants a ventilation assistée avec
casque ou cagoule - Exigences, essais, marquage
Ta slovenski standard je istoveten z: EN 12941:1998/A1:2003
ICS:
13.340.30 Varovalne dihalne naprave Respiratory protective
devices
SIST EN 12941:1999/A1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 12941:1998/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2003
ICS 13.340.30
English version
Respiratory protective devices - Powered filtering devices
incorporating a helmet or a hood - Requirements, testing,
marking
Appareils de protection respiratoire - Appareils filtrants à Atemschutzgeräte - Gebläsefiltergeräte mit einem Helm
ventilation assistée avec casque ou cagoule - Exigences, oder einer Haube - Anforderungen, Prüfung,
essais, marquage Kennzeichnung
This amendment A1 modifies the European Standard EN 12941:1998; it was approved by CEN on 3 November 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slova
...